Shimano SC-M9051 Manual

Shimano Ikke kategoriseret SC-M9051

Læs nedenfor 📖 manual på dansk for Shimano SC-M9051 (12 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 20 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/12
System Information
Display
IMPORTANT NOTICE
•Contact the place of purchase or a distributor for information on
installation, adjustment, and replacement of the products which are not
found in the user's manual. A dealer's manual for professional and
experienced bicycle mechanics is available on our website (https://si.
shimano.com).
•The Bluetooth® word mark and logos are registered trademarks owned
by the Bluetooth SIG, Inc. and any use of such marks by SHIMANO INC.
is under license. Other trademarks and trade names are those of their
respective owners.
For safety, be sure to read this “user's manual”
thoroughly before use, follow it for correct use, and
store it so that it can be referenced at any time.
The following instructions must be observed at all times in order to
prevent personal injury and physical damage to equipment and
surroundings. The instructions are classified according to the degree of
danger or damage which may occur if the product is used incorrectly.
DANGER Failure to follow the instructions will result
in death or serious injury.
WARNING Failure to follow the instructions could
result in death or serious injury.
CAUTION
Failure to follow the instructions could
cause personal injury or physical damage
to equipment and surroundings.
Important safety information
WARNING
•Do not disassemble or modify the product. This may cause the product
to not operate correctly, and you may suddenly fall and be seriously
injured.
•When operating the shift switch, be careful not to allow your
fingers to be caught in the derailleur. The powerful motor which
drives the electronic gear shifting derailleur will operate
without stopping until the shifting position is reached.
Notice
•If using a system information display, use it together as a set with one
of the following units.
External type: BM-DN100, built-in type: BT-DN110
•Be sure to attach dummy plugs to any unused E-TUBE ports. If water
gets into any of the components, operating problems or rusting may
result.
•Do not keep connecting and disconnecting the small waterproof
connector. It may impair the function.
•Be careful not to get water into the E-TUBE ports.
•The components are designed to be fully waterproofed to withstand
wet weather riding conditions; however, do not deliberately place them
into water.
•Do not clean the bicycle with a high-pressure washer. If water gets into
any of the components, operating problems or rusting may result.
•Handle the components carefully, and avoid subjecting them to strong
shock.
•Do not use thinner or other solvents to clean the products. Such solvents
may damage the surface.
•Contact the place of purchase for updates of the component software.
The most up-to-date information is available on the SHIMANO website.
•Disconnect the Bluetooth LE connection when not using E-TUBE
PROJECT for smartphones/tablets. Using a system information display
without disconnecting the Bluetooth LE connection could increase
battery consumption.
•Products are not guaranteed against natural wear and deterioration
from normal use and aging.
•For maximum performance we highly recommend SHIMANO lubricants
and maintenance products.
Regular inspections before riding the bicycle
Before riding the bicycle, check the following items. If any problems are
found, consult your place of purchase or a distributor.
•Is the system information display securely installed to the handlebar?
•Is there sufficient charge remaining in the battery?
•Is there any noticeable damage to the electric wires?
•Are the dummy plugs attached to any unused E-TUBE ports?
Names of parts
Some items may not be able to be displayed or selected,
depending on the connected components and software version.
For information on the items available with the product being
used, contact the place of purchase.
Display
Charge socket A B C D
E-TUBE port
Mode switch
ABattery level
BFront derailleur Gear position
CRear derailleur Gear position/RD protection reset mode
DSuspension setting
EOperation mode
A. Battery level
Display Battery level
81% - 100%
61% - 80%
41% - 60%
26% - 40%
1% - 25%*1*2*3
0%*3
*1 When the battery level is low, the operation of the suspension will be
limited to the lock release direction. The operation of the rear
suspension is restricted first, then that of the front suspension in the
same manner.
*2 When the battery level drops below 5%, the operation of the front
derailleur is restricted.
*3 When the battery level decreases further, both the suspensions and
derailleurs cease operating, with the derailleurs fixed at the last
shifted position. The battery indicator blinks for 2 seconds at the time
of input operation. It is recommended to charge the battery as soon
as possible.
B. Front derailleur Gear position
The gear position of the front derailleur is displayed.
Display Gear position
Largest chainring
Middle chainring
Smallest chainring
* In the case of double specification, only the largest chainring and
smallest chainring are displayed.
C. Rear derailleur Gear position/RD protection reset mode
Display Details
Number The gear position of the rear derailleur is displayed.
RD protection reset will operate.
D. Suspension setting
Three types of front and rear suspension combinations can be configured.
Display Details
If the suspension settings are already configured, one of the
settings can be selected from the screen indications. *1*2
If the suspension settings are not configured, the
suspensions are not connected, or the battery level is
running low, the display will be blank.
*1 Suspension settings are configured in E-TUBE PROJECT. For details,
consult your place of purchase or a distributor.
*2 Depending on the type of suspension, settings may be factory
configured at the time of shipment. Check the indications displayed
on the system information display screen, and if the arrows are
displayed, be sure to check the setting details.
E. Operation mode
Displays the operation mode.
Display Mode Details
Front derailleur/rear
derailleur
adjustment
Adjustment setting is done in this
mode. For the setting procedure,
contact your place of purchase or a
distributor.
Manual shift Gears are shifted manually in this
mode.
Shift mode 1 The shift mode set in E-TUBE
PROJECT can be used.
Shift mode 2
Functions
Cycle computer connection
The system information display transmits the following four types of
information to cycle computers or receivers that are compatible with
ANT+™ or Bluetooth® LE connections:
•Gear position information (front and rear)
•Di2 battery level information
•Adjustment mode information
•D-FLY channel switch information
For information on which of the above is displayed, refer to the manual
for your cycle computer or receiver.
* You can check the latest functions by using E-TUBE PROJECT to
update the software. Please contact your place of purchase for
details.
E-TUBE PROJECT connection
E-TUBE PROJECT for smartphones/tablets may be used if a Bluetooth LE
connection is established with a smartphone/tablet.
Connection method
Cycle computer connection
To connect, the cycle computer needs to be in “connection mode.” For
information on how to put the cycle computer into connection mode,
refer to the manual for your cycle computer.
1. Put the cycle computer into connection mode.
2. Perform gear shifting operations.
If you cannot connect after performing gear shifting operations,
perform the following operations.
In the case of an external battery
Check that the electric wires are connected to the system information
display, then remove and remount the external battery.
In the case of a built-in battery
Check that the electric wires are connected to the system information
display, then remove the electric wires from the system information
display and reconnect them. (Connection communication begins
approximately 30 seconds after the battery is reinstalled or the electric
wire is reconnected to the system information display.)
3. Connection is complete.
Check on the cycle computer to see if connection has been successful.
If connection cannot be performed in the way described above, refer to
the manual for your cycle computer.
For information on how to show the number of gears or the Di2 battery
level, refer to the manual for the cycle computer.
E-TUBE PROJECT connection
Before setting up a connection, turn on Bluetooth LE on the smartphone/
tablet.
1. Start E-TUBE PROJECT and set it to listen for Bluetooth LE signals.
UM-7GC0C-000 User's Manual

Produkt Specifikationer

Mærke: Shimano
Kategori: Ikke kategoriseret
Model: SC-M9051

Har du brug for hjælp?

Hvis du har brug for hjælp til Shimano SC-M9051 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Shimano Manualer

Shimano

Shimano BR-M8120 Manual

7 Oktober 2024
Shimano

Shimano SL-RV400-6R Manual

7 Oktober 2024
Shimano

Shimano SL-RV300-6R Manual

6 Oktober 2024
Shimano

Shimano ST-2400-R Manual

6 Oktober 2024
Shimano

Shimano CN-HG901-11 Manual

6 Oktober 2024
Shimano

Shimano DH-T785 Manual

4 Oktober 2024
Shimano

Shimano CLARIS 2400 ST-R240-R Manual

1 Oktober 2024
Shimano

Shimano SL-RV300-7R Manual

1 Oktober 2024
Shimano

Shimano SL-RV400-LN Manual

1 Oktober 2024
Shimano

Shimano SL-RV400-7R Manual

1 Oktober 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg

Smeg KIT6PX Manual

23 December 2024
Smeg

Smeg KIT6CX Manual

23 December 2024
Smeg

Smeg GTA-6 Manual

23 December 2024
Lucide

Lucide Casper i 79166/19/12 Manual

23 December 2024
Lucide

Lucide Merlina 78193/30/66 Manual

23 December 2024
Lucide

Lucide Pippa 77583/81/30 Manual

23 December 2024
Lucide

Lucide Pia 45380/04/30 Manual

23 December 2024
Lucide

Lucide Pia 45280/01/30 Manual

23 December 2024
Lucide

Lucide Anaka 45179/03/30 Manual

23 December 2024
Lucide

Lucide Zych 45156/01/97 Manual

23 December 2024