Shimano SL-M780-L Manual

Shimano Cykel tilbehør SL-M780-L

Læs nedenfor 📖 manual på dansk for Shimano SL-M780-L (1 sider) i kategorien Cykel tilbehør. Denne guide var nyttig for 5 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/1

SM-BB70 / SM-BB71-41A

FC-M785

38-26T

104 / 64 mm

165, 170, 175, 180 mm

48.8 mm

68, 73 mm

BC1.37 (68, 73mm)

40-28T

104 / 64 mm

165, 170, 175, 180 mm

48.8 mm

68, 73 mm

BC1.37 (68, 73mm)

Tightening torque:

0.08 N·m {0.7 in. lbs.}

1. Install the pin plate to the newly-

assembled shifting lever unit.

* Insert the projections on the pin

plate into the holes in the shifting

lever unit as shown in the

illustration.

2. Align the shifting lever unit and the

bracket, and then secure with the

four shifting lever unit mounting

screws.

* Install the M5 bolt spacer before

securing the screws.

3. Tighten the unit fixing bolt.

4. Install the adjustment barrel.

5. Install the indicator unit by following the assembly procedure

given in “Replacement of the indicator unit”.

* There is no pin plate installed to the SL-M780-I.

• Install the shifting lever in a position

where it will not obstruct brake operation

and gear shifting operation.

• Do not use in a combination which

causes brake operation to be obstructed.

Note:

When installing the components to carbon frame/handle bar

surfaces, verify with the manufacturer of the carbon frame/parts for

their recommendation on tightening torque in order to prevent over

tightening that can cause damage to the carbon material and/or

under tightening that can cause lack of fixing strength for the

components.

Note:

The mode converter cannot be switched while the lever is at the

lowest position. Be sure to operate lever (A) one or more times

before switching. Do not turn the mode converter by force, otherwise

it may break.

Mode converter

Mode select switch

Lever (A)

Model number

Normal type

Top route type

Front chainwheel tooth difference

Front derailleur installation band diameter

Chainstay angle (a)

Front Derailleur

One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003

Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: +31-341-272222

3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan

* Service Instructions in further languages are available at :

http://techdocs.shimano.com

Please note: specifications are subject to change for improvement without notice. (English)

This service instruction explains how to use and maintain the

Shimano bicycle parts which have been used on your new bicycle.

For any questions regarding your bicycle or other matters which

are not related to Shimano parts, please contact the place of

purchase or the bicycle manufacturer.

General Safety Information

WARNING

“Maintenance interval depends on the usage and riding circumstances. Clean regularly the chain

with an appropriate chaincleaner. Never use alkali based or acid based solvents such as rust

cleaners. If those solvent be used chain might break and cause serious injury.”

• In order to obtain good gear shifting performance, this chain has a forward side and a reverse side, and the

sides are marked so that the chain will face the correct way when installed. The proper design performance

will be obtained when the chain is installed so that it faces the correct way. If it is installed so that it faces the

opposite way, the chain may come off and the bicycle may fall over and serious injury may occur as a result.

• Use the reinforced connecting pin only for connecting the narrow type of chain.

• If connecting pins other than reinforced connecting pins

are used, or if a reinforced connecting pin or tool which is

not suitable for the type of chain is used, sufficient

connection force may not be obtained, which could cause

the chain to break or fall off.

• If it is necessary to adjust the length of the chain due to a

change in the number of sprocket teeth, make the cut at

some other place than the place where the chain has

been joined using a reinforced connecting pin. The chain will be damaged if it is cut at a place

where it has been joined with a reinforced connecting pin.

• Be careful not to let the cuffs of your clothes get caught in the chain while riding, otherwise you

may fall off the bicycle.

• Check that the tension of the chain is correct and that the chain is not damaged. If the tension is

too weak or the chain is damaged, the chain should be replaced. If this is not done, the chain may

break and cause serious injury.

• The two left crank arm mounting bolts should be tightened alternately in stages rather than each bolt being fully tightened all at

once. Use a torque wrench to check that the final tightening torques are within the range of 12 - 14 N·m. Furthermore, after riding

approximately 100 km (60 miles), use a torque wrench to re-check the tightening torques. It is also important to periodically check

the tightening torques. If the tightening torques are too weak or if the mounting bolts are not tightened alternately in stages, the left

crank arm may come off and the bicycle may fall over, and serious injury may occur as a result.

• Check that there are no cracks in the crank arms before riding the bicycle. If there are any cracks, the crank arm may break and you

may fall off the bicycle.

• If the inner cover is not installed correctly, the axle may rust and become damaged, and the bicycle may fall over and serious injury

may occur as a result.

• Obtain and read the service instructions carefully prior to installing the parts. Loose, worn or damaged parts may cause the

bicycle to fall over and serious injury may occur as a result. We strongly recommend only using genuine Shimano replacement

parts.

• Obtain and read the service instructions carefully prior to installing the parts. If adjustments are not carried out correctly, the

chain may come off and this may cause you to fall off the bicycle which could result in serious injury.

• Read these Technical Service Instructions carefully, and keep them in a safe place for later reference.

• If the chain is on the smallest or intermediate chainring, there is the danger of injury from the tips of the teeth on the largest

chainring.

Note

• In addition, if pedaling performance does not feel normal, check this once more.

• Before riding the bicycle, check that there is no play or looseness in the connection. Also, be sure to retighten the crank arms and

pedals at periodic intervals.

• When installing the pedals, apply a small amount of grease to the threads to prevent the pedals from sticking. Use a torque wrench

to securely tighten the pedals. Tightening torque: 35 - 55 N·m {305 - 479 in. lbs.}. The right-hand crank arm has a right-hand thread,

and the left-hand crank arm has a left-hand thread.

• If a squeaking noise is heard coming from the bottom bracket axle and the left crank arm connector, apply grease to the connector

and then tighten it to the specified torque.

• Use a neutral detergent to clean the crank arm and the bottom bracket. Using alkaline or acidic detergents may cause discoloration.

• Do not wash the bottom bracket with high-pressure jets of water.

• If you feel any looseness in the bearings, the bottom bracket should be replaced.

• If gear shifting operations do not feel smooth, wash the derailleur and lubricate all moving parts.

• If the amount of looseness in the links is so great that adjustment is not possible, you should replace the derailleur.

• You should periodically wash the chainrings in a neutral detergent and then lubricate them again. In

addition, cleaning the chain with neutral detergent and lubricating it can be an effective way of extending

the useful life of the chainrings and the chain.

• If the chain keeps coming off the chainrings during use, replace the chainrings and the chain.

• When the chain is in the position shown in the illustration, the chain may contact the front chainrings or

front derailleur and generate noise. If the noise is a problem, shift the chain onto the next-larger rear

sprocket or the one after.

• For frames with suspension, the chain stay angle will vary depending on whether the bicycle is being

ridden or not being ridden. When the bicycle is not being ridden and the chain is positioned on the

largest/larger chainring and on the smallest sprocket, the chain guide outer plate of the front derailleur may

touch the chain.

• The cuffs of your clothing may get dirty from the chain while riding.

• Apply grease to the left and right adapters before installing them.

• For smooth operation, use the specified outer casing and the bottom bracket cable guide.

• The front derailleur is for double front chainwheels only. It cannot be used with triple front chainwheels, as the

shifting points will not match.

• When installing the top route type, choose a frame that has three outer casing holders as shown in the illustration at right.

• Use an outer casing which still has some length to spare even when the handlebars are turned all the way to both sides.

Furthermore, check that the shifting lever does not touch the bicycle frame when the handlebars are turned all the way.

• A special grease is used for the gear shifting cable. Do not use DURA-ACE grease or other types of grease, otherwise they may

cause deterioration in gear shifting performance.

• Grease the inner cable and the inside of the outer casing before use to ensure that they slide properly.

• Operation of the levers related to gear shifting should be made only when the front chainwheel is turning.

• If the brake fluid used in the oil disc brakes is of a type which tends to adhere to the plastic parts of the shifting lever, this may

cause the plastic parts to crack or become discolored. Therefore, you should make sure that the brake fluid does not adhere to

these plastic parts. The mineral oil which is used in SHIMANO disc brakes does not cause cracking or discoloration if it adheres to

plastic parts, but such parts should be cleaned with alcohol beforehand to prevent foreign particles from adhering.

• Do not disassemble the indicator and shifting lever unit, as this may damage them or cause mis-operation.

• Be sure to read the service instructions for the Rear Drive System in conjunction with these service instructions (SL-M780-I).

• Parts are not guaranteed against natural wear or deterioration resulting from normal use.

• For maximum performance we highly recommend Shimano lubricants and maintenance products.

• For any questions regarding methods of installation, adjustment, maintenance or operation, please contact a professional bicycle

dealer.

Outer casing holders

Front

chainrings

Rear

sprockets

SI-5MZ0A-001 Technical Service Instructions

Specifications

X = Available

Installation band diameters:

S (28.6 mm), M (31.8 mm), L (34.9 mm)

When using the S, M size, use an

installation band with a diameter of 28.6

mm, 31.8mm and install it to a L size

adapter.

Chainstay angle

Chainwheel

Model number

Chainwheel tooth combination

Bolt circle diameter

Crank arm length

Chain line

Bottom bracket shell width

Thread dimensions

Applicable bottom bracket

SI-5MZ0A-001-00

Front Drive System (2x10)

Series XT (2x10)

SL-M780-L / SL-M780-IL

OT-SP41

FD-M785 / FD-M785-E2 / FD-M786 / FD-M786-D

FC-M785

CN-HG94

SM-SP17

Shifting lever

Outer casing

Front derailleur

Front chainwheel

Chain

Bottom bracket cable guide

In order to realize the best performance, we recommend that the following combination be used.

(1) Check whether the width of the bottom bracket

shell is 68 mm or 73 mm.

(2) Next, install the adapter while referring to the

illustrations.

Band Type Bracket Type

68 mm

Spacer

2.5 mm

68 mm BB mount-type

bracket

73 mm 73 mm

Installation of the Front Chainwheel

Follow the procedure in the figure.

1, 2 Use the special tool TL-FC32/36 to install the right adapter

(counterclockwise thread) and the left adapter (clockwise

thread).

Tightening torque: 35 - 50 N·m {305 - 435 in. lbs.}

Note : Spacers may be necessary depending on the bottom

bracket shell width. For details, refer to "Spacer

installation method”.

3Insert the right crank unit.

4Set section A of the left crank into the axle of the right crank

unit where the groove is wide.

5Use the TL-FC16/18 to tighten the cap.

Tightening torque: 0.7 - 1.5 N·m {6 - 13 in. lbs.}

6Push in the stopper plate and check that the plate pin is

securely in place, and then tighten the bolt of the left crank

arm. (5 mm Allen key)

Note : Each of the bolts should be evenly and equally

tightened to 12 - 14 N·m {106 - 122 in. lbs.}.

■Spacer installation method

Reinforced Connecting Pin

Link Pin Link Pin

Chain toolChain

10-speed super narrow

chain for

MTB

Reinforced

connecting pin

TL-CN32

TL-CN23

TL-CN27

with groove (3)

with groove (2)

* If using a bottom bracket shell having a width of

68 mm which is a band type, an 1.8 mm spacer

and a 0.7 mm spacer can be used together

instead of a 2.5 mm spacer.

Attach the same outer end cap to the cut end of the outer casing.

Outer end cap

Cutting the outer casing

When cutting the outer casing, cut the opposite end to the end with

the marking. After cutting the outer casing,

make the end round so that the inside of the

hole has a uniform diameter.

CAUTION

Chain length

Add 2 links (with the chain on both

the largest sprocket and the large

chainring).

Largest sprocket Large chainring

Chain

To shift from the smaller chainring to the larger chainring

(Lever A)

When lever (A) is pressed once, there is a shift of one step from the

smaller chainring to the larger chainring.

Example:

From smaller chainring to larger chainring.

To shift from the larger chainring to the smaller chainring

(Lever B)

When lever (B) is pressed once, there is a shift of one step from the

larger chainring to the smaller chainring.

Example:

From larger chainring to smaller chainring.

Gear shifting operation

The INSTANT RELEASE mechanism makes fast releasing possible because cable tension is released immediately when a lever is

depressed. This release lever is equipped with a 2-way release mechanism which allows release operations to be carried out by either

pushing or pulling the lever.

Both lever (A) and lever (B) always return to the initial position when they are released after shifting.

When operating one of the levers, always be sure to turn the crank arm at the same time.

Lever (A) initial position Lever (B)

• 2-WAY RELEASE

Install the inner hole cover by turning it as

shown in the illustration until it stops.

Do not turn it any further than this, otherwise

it may damage the thread on the cover.

Operate lever A once to set it to the middle position. Switch the

mode converter to the 2x (double mode) position.

Inner hole cover

Tightening torque :

3 N·m {27 in. lbs.}

4 mm Allen key

Use a handlebar grip with a maximum

outer diameter of 32 mm.

Installation of the shifting lever

Connecting and securing the inner cable

Switch the mode converter to the 3x (triple mode) position, and then

check the lowest position. Operate lever B two times or more to set

the lever to the lowest position. Remove the inner hole cover, and

install the cable.

Inner hole cover

Inner cable

Lever (B)

Refer to the FD-M785 / M785-E2 / M786 / M786-D (Front

Derailleur) Service Instructions for details on installing the

front derailleur and SIS adjustment.

Applicable chain line 48.8 mm

FD-M785

14T

S, M, L

66° - 69°

44-38T

FD-M785-E2

12T

–

66° - 69°

40-38T

FD-M786

14T

S, M, L

66° - 69°

44-38T

FD-M786-D

14T

–

66° - 69°

44-38T

Note:

Do not force the mode select switch to turn. If you force it to turn, it

will break.

Mode converter

Mode select switch

Stopper plate

Plate pin

Push up

Note :

Set the stopper plate in the right direction as shown

in illustration.

(A)

TL-FC16

TL-FC32 Wide groove area

Inner cover

Replacement and reassembly of the

indicator unit and shifting lever unit

Carry out disassembly and reassembly only when replacing the

indicator unit and the shifting lever unit.

1. Operate lever B two times or more to set the lever to the lowest

position.

2. Remove the indicator fixing screws (a) and (b) which are securing

the indicator unit, and then lift up the lens of the indicator unit to

disengage the catch as shown in the illustration. Then remove the

indicator unit.

* Do not mix up screws (a) and (b).

If they are mixed up, damage may result.

1. Operate lever B two times or more to set the lever to the lowest

position.

2. Check that the indicator needle is at the right edge. (Fig. 1)

3. Install the indicator unit by first engaging the catch, and then

secure it by tightening indicator fixing screws (a) and (b).

4. Check the operation. If the indicator unit does not operate

correctly, reassemble while paying particular attention to steps 1

and 2.

■Replacement of the indicator unit

■Replacement and reassembly of the shifting lever unit

Indicator fixing screw

Catch

1. Loosen the cable fixing bolt (nut) of the front derailleur, and then

pull the inner cable out of the shifting lever unit in the same way

as when installing the inner cable.

2. Remove the indicator unit by following the disassembly procedure

given in “Replacement of the indicator unit”.

3. Remove the adjustment barrel.

4. Remove the unit fixing bolt.

5. Remove the four shifting lever unit mounting screws, and then

remove the shifting lever unit as shown in the illustration.

* Be careful not to mix up screws A, B, and C.

6. Remove the pin plate from the shifting lever unit.

M5 bolt spacer

Pin plate

Unit fixing bolt (M5 x 9.5 mm)

Adjustment barrel

■For details on reassembly without the indicator and

reassembly of the bracket band (SM-SL78), refer to the

Service Instructions for the rear drive system.

Pin plate

Tightening torque:

2.5 N·m {22 in. lbs.}

Tightening torque:

0.15 N·m {1.3 in. lbs.}

Fig. 1

Shifting lever mounting screw

(Small)

Shifting lever mounting screw

(Large)

Shifting lever mounting screw

(Large)

Tightening torque:

0.5 N·m {4 in. lbs.}

Tightening torque:

0.15 N·m {1.3 in. lbs.}

Produkt Specifikationer

Mærke:	Shimano
Kategori:	Cykel tilbehør
Model:	SL-M780-L

Har du brug for hjælp?

Hvis du har brug for hjælp til Shimano SL-M780-L stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Cykel tilbehør Shimano Manualer

Shimano FD-M8000-L Manual

4 Oktober 2024

Shimano FD-M6020-L Manual

30 September 2024

Shimano SM-RT70 Manual

16 September 2024

Shimano SM-CA70 Manual

14 September 2024

Shimano PD-M324 Manual

11 September 2024

Shimano Deore XT PD-M8120 Manual

6 September 2024

Shimano SL-3S41E Manual

5 September 2024

Shimano ST-M4000-L Manual

13 August 2024

Shimano FD-M8000-H Manual

13 August 2024

Shimano FD-M8025-H Manual

8 August 2024

Cykel tilbehør Manualer

Nyeste Cykel tilbehør Manualer

Knog Oi Luxe Manual

26 September 2024

Lezyne Trigger Drive CO2 Manual

24 September 2024

Giant Downtown Manual

14 September 2024

Knog Milk Man Manual

13 September 2024

Thule Lock Kit Manual

13 September 2024

Abus WBA65 Manual

5 September 2024

Topeak PRESSURE-RITE SHOCK ADAPTER Manual

5 September 2024

Funn Ripper Manual

2 September 2024

Funn Mamba Manual

2 September 2024

Basil Bremen Manual

31 August 2024