Shimano SM-EW90-B Manual

Shimano Ikke kategoriseret SM-EW90-B

Læs nedenfor 📖 manual på dansk for Shimano SM-EW90-B (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 13 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

Junction [A]

IMPORTANT NOTICE

•Contact the place of purchase or a distributor for information on

installation, adjustment, and replacement of the products which are not

found in the user's manual. A dealer's manual for professional and

experienced bicycle mechanics is available on our website (https://si.

shimano.com).

•The Bluetooth® word mark and logos are registered trademarks owned

by the Bluetooth SIG, Inc. and any use of such marks by SHIMANO INC.

is under license. Other trademarks and trade names are those of their

respective owners.

For safety, be sure to read this “user's manual”

thoroughly before use, follow it for correct use, and

store it so that it can be referenced at any time.

The following instructions must be observed at all times in order to

prevent personal injury and physical damage to equipment and

surroundings. The instructions are classified according to the degree of

danger or damage which may occur if the product is used incorrectly.

DANGER Failure to follow the instructions will result

in death or serious injury.

WARNING Failure to follow the instructions could

result in death or serious injury.

CAUTION

Failure to follow the instructions could

cause personal injury or physical damage

to equipment and surroundings.

Important safety information

WARNING

•Do not disassemble or modify the product. This may cause the product

to not operate correctly, and you may suddenly fall and be seriously

injured.

•When operating the shifting switch, be careful not to allow your

fingers to be caught in the derailleur. The powerful motor which

drives the electronic gear shifting derailleur will operate

without stopping until the shifting position is reached.

Notice

•Be sure to attach dummy plugs to any unused E-TUBE ports.

•Do not keep connecting and disconnecting the small waterproof

connector. It may impair the function.

•Be careful not to get water into the E-TUBE ports.

•The components are designed to be fully waterproofed to withstand

wet weather riding conditions; however, do not deliberately place them

into water.

•Do not clean the bicycle with a high-pressure washer. If water gets into

any of the components, operating problems or rusting may result.

•Handle the components carefully, and avoid subjecting them to strong

shock.

•Do not use the thinners or harsh solvents to clean the products. Such

solvents may damage the surface.

•Contact the place of purchase for updates of the component software.

The most up-to-date information is available on the SHIMANO website.

•Products are not guaranteed against natural wear and deterioration

from normal use and aging.

•For maximum performance we highly recommend SHIMANO lubricants

and maintenance products.

This device complies with part 15 of the FCC Rules. Operation is subject

to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may

cause undesired operation.

Regular inspections before riding the bicycle

Before riding the bicycle, check the following items. If any problems are

found, consult your place of purchase or a distributor.

•Is junction [A] fully secured?

•Is there sufficient charge remaining in the battery?

•Is there any noticeable damage to the electric wires?

Names of parts

Button

LED window for button

LED window for remaining battery display

Junction [A] E-TUBE port

Connection method

Bluetooth® LE connection

The firmware versions for Bluetooth® LE connection-compatible devices

are shown below.

•BM-DN100 and BT-DN110: Ver. 4.2.3 or later

•EW-WU111 and EW-WU101: Ver. 4.1.1 or later

Before setting up a connection, turn on Bluetooth LE on the smartphone/

tablet.

1. Start E-TUBE PROJECT and set it to listen for Bluetooth LE signals.

2. Press the junction [A] button until the green LED and red LED start

blinking alternately. The bicycle side is ready to connect. The unit

name is displayed on the E-TUBE PROJECT screen.

* Release the mode switch or button as soon as the bicycle side is ready

to be connected. If the mode switch or button is held down for any

longer, a different mode will be activated.

3. Select the unit name displayed on screen.

* When disconnecting, cancel the Bluetooth LE connection from the

smartphone/tablet. (The bicycle will switch from the connection mode

to the normal operation mode.)

How to operate

Switching operation modes

Operation differs depending on the combined unit.

0.5 seconds

or more

3 seconds or

Hold down

External type: SM-BMR1, SM-BMR2, built-in type: SM-BTR2

RD protection reset mode

Adjustment mode

Shift mode

To end adjustment mode or RD protection reset mode, press for 0.5

seconds or more.

For the setting procedure, contact your place of purchase or a distributor.

0.5 seconds

or more

2 seconds or

Hold down

External type: BM-DN100, built-in type: BT-DN110

Adjustment mode

5 seconds or

RD protection reset mode

Bluetooth LE connection mode

Shift mode

To end adjustment mode or RD protection reset mode, press for 0.5

seconds or more.

For the setting procedure, contact your place of purchase or a distributor.

Selecting / confirming the shift mode

Double click the button to switch the shift mode.

The LED changes as shown in the figure below each time the shift mode

switches. To confirm the current shift mode, continue to hold a shifting

switch connected to junction [A] for 0.5 seconds or more. After the

junction [A] LED window displays the battery level, the LED window will

show the current shift mode, as shown in the figure below.

LED display when selecting / conﬁrming shift mode

Manual shift

Shift mode 1

Shift mode 2

Green (2 seconds)Remaining battery

display LED:

Red (2 seconds)Button LED:

Flashing green (twice)Remaining battery

display LED:

Flashing red (twice)Button LED:

Flashing green (3 times)Remaining battery

display LED:

Flashing red (3 times)Button LED:

About the RD protection function

* Rotate the front chainwheel while restoring operation after the RD

protection function has activated.

In order to protect the system when the bicycle falls and is subjected to a

strong impact, the RD protection function will activate and momentarily

sever the connection between the motor and the link, impairing the

proper function of the rear derailleur. When this happens, hold the

junction [A] button down for 5 seconds or more. This will restore the

connection between the motor and the link, and clear the RD protection

function for the rear derailleur. When recovery cannot be performed via

button operations, it may be possible by hand. Check with the place of

purchase in advance.

Press and hold

button

Red Flashing red RD protection

reset

Button (push)

Requires approximately 5 seconds

Complete

Red

When the button LED is lit red, the rear derailleur will not shift. Press the

button until the button LED turns off.

Checking the battery level display

Press and hold a shifting switch connected to junction [A] for 0.5 seconds

or more. The LED window for showing the remaining battery display will

illuminate according to the figure below. After that, the current shift

mode is displayed.

100% 25%

Green (2 seconds)

Flashing green

(5 times)

Red (2 seconds)

Flashing red

(5 times)

50%

* When the battery level is low, the front derailleur stops operating

first, then the rear derailleur. When the battery is completely drained,

the derailleurs are fixed at the last gear position. It is recommended

to charge the battery as soon as possible when the battery indicator

lights red.

UM-7FE0B-000 User's Manual

Please note: specifications are subject to change for improvement without notice. (English)

One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003

High Tech Campus 92, 5656 AG Eindhoven, The Netherlands Phone: +31-402-612222

Roebuck Way, Knowlhill, Milton Keynes, Buckinghamshire, MK5 8HL, United Kingdom

3-77 Oimatsu-cho, Sakai-ku, Sakai City, Osaka 590-8577, Japan

Produkt Specifikationer

Mærke:	Shimano
Kategori:	Ikke kategoriseret
Model:	SM-EW90-B

Har du brug for hjælp?

Hvis du har brug for hjælp til Shimano SM-EW90-B stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Shimano Manualer

Shimano BR-M8120 Manual

7 Oktober 2024

Shimano SL-RV400-6R Manual

7 Oktober 2024

Shimano SL-RV300-6R Manual

6 Oktober 2024

Shimano ST-2400-R Manual

6 Oktober 2024

Shimano CN-HG901-11 Manual

6 Oktober 2024

Shimano DH-T785 Manual

4 Oktober 2024

Shimano CLARIS 2400 ST-R240-R Manual

1 Oktober 2024

Shimano SL-RV300-7R Manual

1 Oktober 2024

Shimano SL-RV400-LN Manual

1 Oktober 2024

Shimano SL-RV400-7R Manual

1 Oktober 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg KIT6PX Manual

23 December 2024

Smeg KIT6CX Manual

23 December 2024

Smeg GTA-6 Manual

23 December 2024

Lucide Casper i 79166/19/12 Manual

23 December 2024

Lucide Merlina 78193/30/66 Manual

23 December 2024

Lucide Pippa 77583/81/30 Manual

23 December 2024

Lucide Pia 45380/04/30 Manual

23 December 2024

Lucide Pia 45280/01/30 Manual

23 December 2024

Lucide Anaka 45179/03/30 Manual

23 December 2024

Lucide Zych 45156/01/97 Manual

23 December 2024