Sitecom WL-610 Manual

Sitecom Router WL-610

Læs nedenfor 📖 manual på dansk for Sitecom WL-610 (65 sider) i kategorien Router. Denne guide var nyttig for 17 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/65

Wireless Network UMTS Router 54G

WL-610

Full manual

Sitecom Wireless Network UMTS Router 54G WL-610

1. Table of Contents

1. TABLE OF CONTENTS ....................................................................................... 2

2. INTRODUCTION ............................................................................................. 4

2.1

HANK YOU

.......................................................................................................4

2.2

EATURES

.........................................................................................................4

2.3

INIMUM

EQUIREMENTS

......................................................................................5

2.4

ACKAGE

ONTENT

..............................................................................................5

3. HARDWARE INSTALLATION ........................................................................... 6

3.1

ANEL

AYOUT

....................................................................................................6

3.1.1 Top panel .................................................................................................6

3.1.2 Rear Panel ................................................................................................7

3.2

ROCEDURE FOR

ARDWARE

NSTALLATION

..................................................................8

3.2.1 Decide where to place your Wireless Broadband Router ..................................8

3.2.2 Setup LAN connection ................................................................................8

3.2.3 Setup WAN connection ...............................................................................8

3.2.4 Power on ..................................................................................................8

4 NETWORK SETTINGS AND SOFTWARE INSTALLATION.................................... 10

4.1

AKE

ORRECT

ETWORK

ETTINGS FOR YOUR

PC.................................................10

5 CONFIGURING WIRELESS BROADBAND ROUTER ............................................ 12

5.1

TART

UP AND

OG IN

.........................................................................................12

5.2

TART

UP AND

OG IN

.........................................................................................13

5.2.1 LAN Settings ...........................................................................................14

5.2.2 Device Status ..........................................................................................16

5.2.3 Internet Status ........................................................................................17

5.2.4 DHCP Client status ...................................................................................18

5.2.5 System Log.............................................................................................19

5.2.6 Statistic ..................................................................................................20

6 RUN SETUP WIZARD ....................................................................................... 21

6.1

WAN

ETUP

..............................................................................................21

6.2

ETUP

.................................................................................................23

7 WIRELESS SETTINGS ...................................................................................... 26

7.1

IRELESS

ASIC

ETTINGS

..................................................................................26

7.2

DVANCED

IRELESS

ETTINGS

............................................................................28

7.3

IRELESS

ECURITY

PTIONS

...............................................................................30

Please check www.sitecom.com for up to date drivers & utilities, manuals and support

7.3.1 WEP Encryption .......................................................................................30

7.3.2 802.1x only.............................................................................................32

7.3.3 WPA Pre-shared key.................................................................................33

7.3.4 WPA Radius.............................................................................................34

7.4

CCESS

ONTROL

..............................................................................................35

8 FIREWALL SETTINGS ...................................................................................... 36

8.1

DMZ.............................................................................................................36

8.2

TTACK

...................................................................................................38

8.3

CCESS

ONTROL

..............................................................................................39

8.4

URL

LOCK

.....................................................................................................41

9 ADVANCED SETTINGS ..................................................................................... 42

9.1

ORT

ORWARDING

............................................................................................42

9.2

IRTUAL

ERVER

...............................................................................................44

9.3

PECIAL

PPLICATIONS

.......................................................................................46

9.4

ALG

ETTINGS

.................................................................................................48

9.5

ETTINGS

...............................................................................................49

9.6

S .............................................................................................................50

10 TOOLBOX ...................................................................................................... 53

10.1

IMEZONE

.....................................................................................................54

10.2

EMOTE

ANAGEMENT

......................................................................................55

10.3

IRMWARE

PGRADE

.........................................................................................57

10.4

ACKUP

ETTINGS

...........................................................................................58

10.5

ESET

(

RESTART

)

THE ROUTER

.............................................................................59

10.6

DDNS .........................................................................................................60

APPENDIX A ...................................................................................................... 61

GLOSSARY ......................................................................................................... 62

Sitecom Wireless Network UMTS Router 54G WL-610

2. Introduction

2.1 Thank you

Thank you for buying the Sitecom Wireless Network UMTS Router 54G WL-610. This Wireless

Broadband Router is a cost-effective IP Sharing Router that enables multiple users to share

the Internet through an ADSL or cable modem. Simply configure your Internet connection

settings in the Wireless Broadband Router and connect your PC to the LAN port and you're

ready to share files and access the Internet.

The Wireless Network UMTS Router is embedded with a IEEE 802.11g/b access point that

allows you to build up a wireless LAN. Besides, it also provides two USB ports which let you

easily share a 3G/UMTS dongle.

2.2 Features

• High Internet Access throughput (50M)

• Allow multiple users to share a single Internet line

• Supports up to 253 users

• Provides two USB port for connection through 3G/UMTS

• Internet Access via Cable, xDSL or 3G modem

• Allow you to share your files via FTP or Network Neighborhood

• Access Private LAN Servers from the Public Network

• Equipped with four LAN ports (10/100M) and one WAN port (10/100M)

• Provides IEEE 802.11g/b wireless LAN access point

• Support DHCP (Server/Client) for easy setup

• Support advanced features such as: Special Applications, DMZ, Virtual Servers,

Access Control, Firewall

• Allows you to monitor the routers status such as: DHCP Client Log, System Log,

Security Log and Device/Connection Status

• Easy to use Web-based GUI for configuration and management purposes

• Remote Management allows configuration and upgrades from a remote site (over the

Internet)

Please check www.sitecom.com for up to date drivers & utilities, manuals and support

2.3 Minimum Requirements

• One External xDSL (ADSL) or Cable modem with an Ethernet port (RJ-45)

• Network Interface Card (NIC) for each Personal Computer (PC)

• PCs with a Web-Browser (Internet Explorer 6.0 or higher, or Netscape Navigator 7.2

or higher)

2.4 Package Content

• One 4-port Wireless Broadband router unit

• One Quick Installation Guide

• One User Manual CD

• One Power Adapter

• CAT-5 UTP Fast Ethernet Cable

Note:

The WAN “idle timeout” auto-disconnect function may not work due to abnormal activities of

some network application software, computer virus or hacker attacks from the Internet. For

example, some software sends network packets to the Internet in the background, even

when you are not using the Internet. So please turn off your computer when you are not

using it. This function also may not work with some ISP. So please make sure this function

can work properly when you use this function in the first time, especially your ISP charge you

by time used.

Sitecom Wireless Network UMTS Router 54G WL-610

3. Hardware Installation

3.1 Panel Layout

3.1.1 Top panel

LED Function Color Status Description

POWER Power indication

Green On Power is being applied to this product.

On The corresponding WAN or LAN port is

linked.

Link/

Modem Link Status Green

Blinking The corresponding WAN or LAN port is

sending or receiving data.

On Wireless LAN had been enabled

WLAN Wireless Activity

Orange

Blinking Sending or receiving data via wireless.

Blinking The corresponding WAN or LAN port is

sending or receiving data.

100Mbps

Data Rate Green

On Data is transmitting in 100Mbps on the

corresponding LAN port.

USB1/2 USB Device Orange

On The USB Device is connected.

Sitecom Wireless Network UMTS Router 54G WL-610

4 Network Settings and Software Installation

To use this product correctly, you have to properly configure the network settings of your

computers and install the attached setup program into your MS Windows platform (Windows

2000/XP).

4.1 Make The Correct Network Settings for your PC

The default IP address of this product is 192.168.0.1, and the default subnet mask is

255.255.255.0. These addresses can be changed on your need, but the default values are

used in this manual. If the TCP/IP environment of your computer has not yet been configured,

you can refer to to configure it. For example, Appendix A

1. configure IP as 192.168.0.100, subnet mask as 255.255.255.0 and gateway as

192.168.0.1, or more easier,

2. configure your computers to load TCP/IP setting automatically, that is, via DHCP

server of this product.

After installing the TCP/IP communication protocol, you can use the ping command to check

if your computer has successfully connected to this product. The following example shows

the ping procedure for Windows 95 platforms. First, execute the command ping

ping 192.168.0.1

If the following messages appear:

Pinging 192.168.0.1 with 32 bytes of data:

Reply from 192.168.0.1: bytes=32 time=1ms TTL=64

a communication link between your computer and this product has been successfully

established. Otherwise, if you get the following messages,

Pinging 192.168.0.1 with 32 bytes of data:

Request timed out.

There must be something wrong in your installation procedure. You have to check the

following items in sequence:

1. Is the Ethernet cable correctly connected between this product and your computer?

Tip: The LAN LED of this product and the link LED of network card on your computer

must be lighted.

2. Is the TCP/IP environment of your computers properly configured?

Please check www.sitecom.com for up to date drivers & utilities, manuals and support

Tip: If the IP address of this product is 192.168.0.1, the IP address of your computer must

be 192.168.0.X and default gateway must be 192.168.0.1.

Sitecom Wireless Network UMTS Router 54G WL-610

5 Configuring Wireless Broadband Router

This product provides a Web based configuration scheme which can be configured by your

Web browser, such as Netscape Communicator or Internet Explorer. This approach can be

adopted in any MS Windows, Macintosh or UNIX based platforms.

5.1 Start-up and Log in

Activate your browser, and disable the proxy or add the IP address of this product into

the exceptions. Then, type this product’s IP address in the Location (for Netscape) or

Address (for IE) field and press ENTER. For example: . http://192.168.0.1

After the connection is established, you will see the web user interface of this product. There

are two appearances of web user interface: for general users and for system administrator.

To log in as an administrator, enter your login name and password (default: admin/admin)

and click . If the password is correct, the web appearance will be changed into OK

administrator configure mode. As listed in its main menu, there are several options for

system administration.

Please check www.sitecom.com for up to date drivers & utilities, manuals and support

Note:

The default IP-address for this router is: 192.168.0.1

5.2 Start-up and Log in

The Status section allows you to monitor the current status of your router. You can use the

Status page to monitor: the connection status of the Broadband router's WAN/LAN interfaces,

Sitecom Wireless Network UMTS Router 54G WL-610

the current firmware and hardware version numbers, any illegal attempts to access your

network, and information on all DHCP client PCs currently connected to your network.

5.2.1 LAN Settings

The LAN Port screen below allows you to specify a private IP address for your router’s LAN

ports as well as a subnet mask for your LAN segment.

Parameters Default Description

IP address This is the router’s LAN port IP address (Your LAN 192.168.0.1

clients default gateway IP address)

IP Subnet Mask Specify a Subnet Mask for your LAN segment 255.255.255.0

802.1d Spanning Tree If 802.1d Spanning Tree function is enabled, this Disabled

router will use the spanning tree protocol to

prevent network loops.

DHCP Server You can enable or disable the DHCP server. By Enabled

Enabling DHCP server the router will

automatically give your LAN clients an IP

address.

Lease Time The DHCP when enabled will temporarily give Forever

Sitecom Wireless Network UMTS Router 54G WL-610

5.2.2 Device Status

View the Broadband router’s current configuration settings. The Device Status displays the

configuration settings you’ve configured in the Wizard / Basic Settings / Wireless

Settings section.

Parameters Description

Device Status This page displays the Broadband router LAN port’s current LAN

IP Address Subnet Mask and . It also shows whether the

DHCP Server function is enabled/disabled.

Please check www.sitecom.com for up to date drivers & utilities, manuals and support

5.2.3 Internet Status

View the Broadband router’s current Internet connection status and other related

information.

Parameters Description

Internet Connection This page displays whether the WAN port is connected to a

Cable/DSL connection. It also displays the router’s WAN port:

WAN IP Subnet Mask address, , and ISP as well as Gateway

the and being used. Primary DNS Secondary DNS

Below the WAN Status you’ll find the WWAN Status, which

displays the 3G connection information: address, WAN IP

Subnet Mask, and ISP Gateway as well as the Primary DNS

and being used. Secondary DNS

Sitecom Wireless Network UMTS Router 54G WL-610

5.2.4 DHCP Client status

View your LAN client's information that is currently linked to the Broadband router's DHCP

server

Parameters Description

Active DHCP Client This page shows all DHCP clients (LAN PCs) currently connected

to your network. The “Active DHCP Client Table” displays the IP

address and the address and Time Expired of each LAN MAC

Client. Use the button to get the most updated Refresh

situation

Please check www.sitecom.com for up to date drivers & utilities, manuals and support

5.2.5 System Log

View the operation log of the system.

Parameters Description

System Log This page shows the current system log of the Broadband router.

It displays any event occurred after system start up.

At the bottom of the page, the system log can be saved

< > to a local file for further processing or the system log Save

can be cleared < > or it can be refreshed < > to Clear Refresh

get the most updated situation. When the system is powered

down, the system log will disappear if not saved to a local file.

Sitecom Wireless Network UMTS Router 54G WL-610

5.2.6 Statistic

View the statistics of packets sent and received on WAN, LAN and Wireless LAN.

Parameters Description

Statistics Shows the counters of packets sent and received on WAN, LAN

and Wireless LAN.

Please check www.sitecom.com for up to date drivers & utilities, manuals and support

6 Run Setup Wizard

You can choose between setting up the WAN port for a normal Cable or xDSL connection, or

run the 3G setup and setup the USB port for use with a 3G USB modem. Follow the steps in

chapter 6.1 for WAN and the steps in chapter 6.2 for 3G.

6.1 Run WAN Setup

• Click to configure the router. Wizard

• The will now be displayed; check that the modem is connected and Setup wizard

click . Next

• Select your country from the list. Country

• From select your internet provider. Click . Service, Next

Sitecom Wireless Network UMTS Router 54G WL-610

• Depending on the chosen provider, you may need to enter your user name and

password, MAC address or hostname in the following window. After you have entered

the correct information, click . Next

• Click to complete the configuration. APPLY

• The router will now save the settings and restart, please wait 60 seconds and you will

be transferred back to the status window. The configuration is complete.

Please check www.sitecom.com for up to date drivers & utilities, manuals and support

• Wait for about 10 seconds to allow the router to connect to the Internet.

6.2 Run 3G Setup

• Click to configure the router. Wizard

• The will now be displayed; check that the modem is connected and Setup wizard

click . Next

• Select your country from the list. Country

• From select 3G Setup. Click . Service, Next

Sitecom Wireless Network UMTS Router 54G WL-610

• Depending on your provider, you may need to enter your user name, password and

PIN code in the following window. After you have entered the correct information,

click . Next

• Click to complete the configuration. APPLY

Please check www.sitecom.com for up to date drivers & utilities, manuals and support

• The router will now save the settings and restart, please wait 60 seconds and you will

be transferred back to the status window. The configuration is complete.

• Wait for about 10 seconds to allow the router to connect to the Internet.

Sitecom Wireless Network UMTS Router 54G WL-610

7 Wireless Settings

7.1 Wireless Basic Settings

You can set parameters that are used for the wireless stations to connect to this router. The

parameters include Mode, ESSID, Channel Number and Associated Client.

Parameters Description

Mode It allows you to set the AP to AP, Station, Bridge or WDS mode.

Band It allows you to set the AP fix at 802.11b or 802.11g mode. You also

can select B+G mode to allow the AP select 802.11b and 802.11g

connection automatically.

ESSID This is the name of the wireless LAN. All the devices in the same

wireless LAN should have the same ESSID. Default ESSID for this

device is: Sitecom

Channel Number The channel used by the wireless LAN. All devices in the same wireless

LAN should use the same channel.

WLAN MAC This is the MAC address used by the Wireless interface of this AP when

it is in the station mode.

Clone MAC Click the “Clone MAC” button will copy the MAC address of your PC,

which you are using to configure the AP, to the WLAN MAC.

MAC address If you want to bridge more than one networks together with wireless

LAN, you have to set this access point to “AP Bridge-Point to Point

mode”, “AP Bridge-Point to Multi-Point mode” or “AP Bridge-WDS

mode”. You have to enter the MAC addresses of other access points

that join the bridging.

Please check www.sitecom.com for up to date drivers & utilities, manuals and support

Set Security Click the “Set Security” button, then a “WDS Security Settings” will pop

up. You can set the security parameters used to bridge access points

together here when your AP is in AP Bridge modes.

Sitecom Wireless Network UMTS Router 54G WL-610

7.2 Advanced Wireless Settings

You can set advanced wireless LAN parameters of this router. The parameters include

Authentication Type, Fragment Threshold, RTS Threshold, Beacon Interval, and Preamble

Type. You should not change these parameters unless you know what effect the changes will

have on this router.

Parameters Description

Authentication Type There are two authentication types: "Open System" and "Shared

Key". When you select "Open System", wireless stations can

associate with this wireless router without WEP encryption. When

you select "Shared Key", you should also setup WEP key in the

"Encryption" page and wireless stations should use WEP encryption

in the authentication phase to associate with this wireless router. If

you select "Auto", the wireless client can associate with this wireless

router by using any one of these two authentication types.

Fragment Threshold "Fragment Threshold" specifies the maximum size of a packet during

the fragmentation of data to be transmitted. If you set this value too

low, it will result in bad performance.

RTS Threshold When the packet size is smaller the RTS threshold, the wireless

router will not use the RTS/CTS mechanism to send this packet.

Beacon Interval The interval of time that this wireless router broadcast a beacon.

Beacon is used to synchronize the wireless network.

Data Rate The “Data Rate” is the rate this access point uses to transmit data

packets. The access point will use the highest possible selected

Please check www.sitecom.com for up to date drivers & utilities, manuals and support

transmission rate to transmit the data packets.

Preamble Type The “Long Preamble” can provide better wireless LAN compatibility

while the “Short Preamble” can provide better wireless LAN

performance.

Broadcast ESSID If you enable “Broadcast ESSID”, every wireless station located

within the coverage of this access point can discover this access point

easily. If you are building a public wireless network, enabling this

feature is recommended. Disabling “Broadcast ESSID” can provide

better security.

IAPP If you enable “IAPP”, it will allow wireless station roaming between

IAPP enabled access points within the same wireless LAN.

802.11g Protection This is also called CTS Protection. It is recommended to enable the

protection mechanism. This mechanism can decrease the rate of

data collision between 802.11b and 802.11g wireless stations. When

the protection mode is enabled, the throughput of the AP will be a

little lower due to many of frame traffic should be transmitted.

Click < at the bottom of the screen to save the above configurations. You can now Apply>

configure other advance sections or start using the router.

Sitecom Wireless Network UMTS Router 54G WL-610

7.3 Wireless Security Options

This Access Point provides complete wireless LAN security functions, include WEP, IEEE

802.11x, IEEE 802.11x with WEP, WPA with pre-shared key and WPA with RADIUS. With

these security functions, you can prevent your wireless LAN from illegal access. Please make

sure your wireless stations use the same security function.

7.3.1 WEP Encryption

When you select 64-bit or 128-bit WEP key, you have to enter WEP keys to encrypt data. You

can generate the key by yourself and enter it. You can enter four WEP keys and select one of

them as default key. Then the router can receive any packets encrypted by one of the four

keys.

Parameters Description

Key Length You can select the WEP key length for encryption, 64-bit or 128-bit. Larger

WEP key length will provide higher level of security, but the throughput will

be lower.

Key Format You may select to select ASCII Characters (alphanumeric format) or

Hexadecimal Digits (in the "A-F", "a-f" and "0-9" range) to be the WEP Key.

For example: ASCII Characters: guest

12345abcde Hexadecimal Digits:

Default Key Select one of the four keys to encrypt your data. Only the key you select it

Please check www.sitecom.com for up to date drivers & utilities, manuals and support

in the "Default key" will take effect.

Key1 - Key4 The WEP keys are used to encrypt data transmitted in the wireless network.

Fill the text box by following the rules below.

64-bit WEP: input (in the " ", " " and " " 10-digit Hex values A-F a-f 0-9

range) or 5-digit ASCII character as the encryption keys.

: input (in the " ", " " and " " 128-bit WEP 26-digit Hex values A-F a-f 0-9

range) or 13-digit ASCII characters as the encryption keys.

Click < at the bottom of the screen to save the above configurations. You can now Apply>

configure other advance sections or start using the router (with the advance settings in

place)

Sitecom Wireless Network UMTS Router 54G WL-610

7.3.2 802.1x only

IEEE 802.1x is an authentication protocol. Every user must use a valid account to login to this

Access Point before accessing the wireless LAN. The authentication is processed by a RADIUS

server. This mode only authenticates users by IEEE 802.1x, but it does not encrypt the data

during communication.

Parameters Description

RADIUS Server IP address The IP address of external RADIUS server.

RADIUS Server Port The service port of the external RADIUS server.

RADIUS Server Password The password used by external RADIUS server.

Click < at the bottom of the screen to save the above configurations. You can now Apply>

configure other advance sections or start using the router (with the advance settings in

place)

Please check www.sitecom.com for up to date drivers & utilities, manuals and support

7.3.3 WPA Pre-shared key

Wi-Fi Protected Access (WPA) is an advanced security standard. You can use a pre-shared

key to authenticate wireless stations and encrypt data during communication. It uses TKIP or

CCMP (AES) to change the encryption key frequently. So the encryption key is not easy to be

broken by hackers. This can improve security very much.

Parameters Description

WPA (TKIP) TKIP can change the encryption key frequently to enhance the

wireless LAN security.

WPA2 (AES) This use CCMP protocol to change encryption key frequently. AES can

provide high level encryption to enhance the wireless LAN security.

WPA2 Mixed This will use TKIP or AES based on the other communication peer

automatically.

Pre-shared Key Format You may select to select Passphrase (alphanumeric format) or

Hexadecimal Digits (in the “A-F”, “a-f” and “0-9” range) to be the

Pre-shared Key. For example: Passphrase: iamguest

: Hexadecimal Digits 12345abcde

Pre-shared Key The Pre-shared key is used to authenticate and encrypt data

transmitted in the wireless network. Fill the text box by following the

rules below. Hex WEP: input 64-digit Hex values (in the “A-F”, “a-f”

and “0-9” range) or at least 8 character pass phrase as the

pre-shared keys.

Sitecom Wireless Network UMTS Router 54G WL-610

7.3.4 WPA Radius

Wi-Fi Protected Access (WPA) is an advanced security standard. You can use an external

RADIUS server to authenticate wireless stations and provide the session key to encrypt data

during communication. It uses TKIP or CCMP (AES) to change the encryption key frequently.

This can improve security very much.

Parameters Description

WPA (TKIP) TKIP can change the encryption key frequently to enhance the

wireless LAN security.

WPA2 (AES) This use CCMP protocol to change encryption key frequently.

AES can provide high level encryption to enhance the wireless

LAN security.

WPA2 Mixed This will use TKIP or AES based on the other communication

peer automatically.

RADIUS Server IP address The IP address of external RADIUS server.

RADIUS Server Port The service port of the external RADIUS server.

RADIUS Server Password The password used by external RADIUS server.

Click < at the bottom of the screen to save the above configurations. You can now Apply>

configure other advance sections or start using the router (with the advance settings in

place)

Please check www.sitecom.com for up to date drivers & utilities, manuals and support

7.4 Access Control

This wireless router provides MAC Address Control, which prevents the unauthorized MAC

Addresses from accessing your wireless network.

Parameters Description

Enable wireless access control Enable wireless access control

Add MAC address into the list Fill in the "MAC Address" and "Comment" of the wireless

station to be added and then click "Add". Then this

wireless station will be added into the "Current Access

Control List" below. If you find any issues before adding

it and want to retype again. Just click "Clear" and both

"MAC Address" and "Comment" fields will be cleared.

Remove MAC address from the list If you want to remove some MAC address from the

"Current Access Control List ", select the MAC addresses

you want to remove in the list and then click "Delete

Selected". If you want remove all MAC addresses from

the table, just click "Delete All" button. Click "Reset" will

clear your current selections.

Click < at the bottom of the screen to save the above configurations. You can now Apply>

configure other advance sections or start using the router (with the advance settings in

place)

Sitecom Wireless Network UMTS Router 54G WL-610

8 Firewall Settings

The Broadband router provides extensive firewall protection by restricting connection

parameters, thus limiting the risk of hacker attack, and defending against a wide array of

common Internet attacks. However, for applications that require unrestricted access to the

Internet, you can configure a specific client/server as a Demilitarized Zone (DMZ).

Note Enable Apply: To enable the Firewall settings select and click

8.1 DMZ

If you have a local client PC that cannot run an Internet application (e.g. Games) properly

from behind the NAT firewall, then you can open the client up to unrestricted two-way

Internet access by defining a DMZ Host. The DMZ function allows you to re-direct all packets

going to your WAN port IP address to a particular IP address in your LAN. The difference

between the virtual server and the DMZ function is that the virtual server re-directs a

particular service/Internet application (e.g. FTP, websites) to a particular LAN client/server,

whereas DMZ re-directs all packets (regardless of services) going to your WAN IP address to

a particular LAN client/server.

Please check www.sitecom.com for up to date drivers & utilities, manuals and support

Parameters Description

Enable DMZ Enable/disable DMZ

Note:

If there is a conflict between the Virtual Server and the DMZ setting, then Virtual Server

function will have priority over the DMZ function.

Public IP Address The IP address of the WAN port or any other Public IP addresses

given to you by your ISP

Client PC IP Address Input the IP address of a particular host in your LAN that will receive

all the packets originally going to the WAN port/Public IP address

above

Note:

You need to give your LAN PC clients a fixed/static IP address for DMZ to work properly.

You can now configure other advance sections or start using the router (with the advance

settings in place)

Sitecom Wireless Network UMTS Router 54G WL-610

8.2 DoS Attack

The Broadband router's firewall can block common hacker attacks, including Denial of

Service, Ping of Death, Port Scan and Sync Flood. If Internet attacks occur the router can log

the events.

Parameters Description

Ping of Death Protections from Ping of Death attack

Discard Ping From WAN The router’s WAN port will not respond to any Ping requests

Port Scan Protection the router from Port Scan.

Sync Flood Protection the router from Sync Flood attack.

Click < at the bottom of the screen to save the above configurations. You can now Apply>

configure other advance sections or start using the router (with the advance settings in

place)

Please check www.sitecom.com for up to date drivers & utilities, manuals and support

8.3 Access Control

If you want to restrict users from accessing certain Internet applications/services (e.g.

Internet websites, email, FTP etc.), then this is the place to set that configuration. Access

Control allows users to define the traffic type permitted in your LAN. You can control which PC

client can have access to these services.

Parameters Description

Deny If you select “Deny” then all PCs will be allowed to access

Internet accept for the PCs in the list below.

Allow If you select “Allow” then all PCs will be denied to access

Internet accept for the PCs in the list below.

Filter client PCs by IP Fill in “IP Filtering Table” to filter PC clients by IP.

Add PC You can click Add PC to add an access control rule for users by

IP addresses.

Remove PC If you want to remove some PC from the "IP Filtering Table",

select the PC you want to remove in the table and then click

"Delete Selected". If you want remove all PCs from the table,

just click "Delete All" button.

Filter client PC by MAC Check “Enable MAC Filtering” to enable MAC Filtering.

Add PC Fill in “Client PC MAC Address” and “Comment” of the PC that is

Sitecom Wireless Network UMTS Router 54G WL-610

allowed to access the Internet, and then click “Add”. If you find

any typo before adding it and want to retype again, just click

"Reset" and the fields will be cleared.

Remove PC If you want to remove some PC from the "MAC Filtering Table",

select the PC you want to remove in the table and then click

"Delete Selected". If you want to remove all PCs from the table,

just click the "Delete All" button. If you want to clear the

selection and re-select again, just click “Reset”.

You can now configure other advance sections or start using the router (with the advance

settings in place)

Please check www.sitecom.com for up to date drivers & utilities, manuals and support

8.4 URL Block

You can block access to some Web sites from particular PCs by entering a full URL address or

just keyword of the Web site.

Parameters Description

Enable URL Blocking Enable/disable URL Blocking

Add URL Keyword Fill in “URL/Keyword” and then click “Add”. You can enter the full

URL address or the keyword of the web site you want to block.

If you find any typo before adding it and want to retype again,

just click "Reset" and the field will be cleared.

Remove URL Keyword If you want to remove some URL keyword from the "Current

URL Blocking Table", select the URL keyword you want to

remove in the table and then click "Delete Selected". If you

want remove all URL keyword from the table, just click "Delete

All" button. If you want to clear the selection and re-select

again, just click “Reset”.

You can now configure other advance sections or start using the router (with the advance

settings in place)

Please check www.sitecom.com for up to date drivers & utilities, manuals and support

Note:

You need to give your LAN PC clients a fixed IP address for Port Forwarding to work properly.

Type This is the protocol type to be forwarded. You can choose to

forward “TCP” or “UDP” packets only or select “both” to forward

both “TCP” and “UDP” packets.

Port Range The range of ports to be forward to the private IP.

Comment The description of this setting.

Add Port Forwarding Fill in the "Private IP", “Type”, “Port Range” and "Comment" of

the setting to be added and then click "Add". Then this Port

Forwarding setting will be added into the "Current Port

Forwarding Table" below. If you find any typo before adding it

and want to retype again, just click "Clear" and the fields will be

cleared.

Remove Port Forwarding If you want to remove some Port Forwarding settings from the

“Current Port Forwarding Table", select the Port Forwarding

settings you want to remove in the table and then click "Delete

Selected". If you want remove all Port Forwarding settings from

the table, just click "Delete All" button. Click "Reset" will clear

your current selections.

Sitecom Wireless Network UMTS Router 54G WL-610

9.2 Virtual Server

Use the Virtual Server function when you want different servers/clients in your LAN to handle

different service/Internet application type (e.g. Email, FTP, Web server etc.) from the

Internet. Computers use numbers called port numbers to recognize a particular

service/Internet application type. The Virtual Server allows you to re-direct a particular

service port number (from the Internet/WAN Port) to a particular LAN private IP address and

its service port number. (See Glossary for an explanation on Port number)

Parameters Description

Enable Virtual Server Enable Virtual Server.

Private IP This is the LAN client/host IP address that the Public Port number

packet will be sent to.

Note:

You need to give your LAN PC clients a fixed/static IP address for Virtual Server to work

properly.

Private Port This is the port number (of the above Private IP host) that the below

Public Port number will be changed to when the packet enters your

LAN (to the LAN Server/Client IP)

Type Select the port number protocol type (TCP, UDP or both). If you are

unsure, then leave it to the default both protocols.

Please check www.sitecom.com for up to date drivers & utilities, manuals and support

Public Port Enter the service (service/Internet application) port number from the

Internet that will be re-directed to the above Private IP address host

in your LAN

Note:

Virtual Server function will have priority over the DMZ function if there is a conflict between

the Virtual Server and the DMZ settings.

Comment The description of this setting.

Add Virtual Server Fill in the "Private IP", "Private Port", "Type", “Public Port” and

"Comment" of the setting to be added and then click "Add". Then this

Virtual Server setting will be added into the "Current Virtual Server

Table" below. If you find any typo before adding it and want to retype

again, just click "Clear" and the fields will be cleared.

Remove Virtual Server If you want to remove some Virtual Server settings from the “Current

Virtual Server Table", select the Virtual Server settings you want to

remove in the table and then click "Delete Selected". If you want

remove all Virtual Server settings from the table, just click "Delete

All" button. Click "Reset" will clear your current selections.

Click < at the bottom of the screen to save the above configurations. You can now Apply>

configure other advance sections or start using the router (with the advance settings in

place)

Sitecom Wireless Network UMTS Router 54G WL-610

9.3 Special Applications

Some applications require multiple connections, such as Internet games, video conferencing,

Internet telephony and others. In this section you can configure the router to support

multiple connections for these types of applications.

Parameters Description

Enable Trigger Port Enable the Special Application function.

Trigger Port This is the out going (Outbound) range of port numbers for this

particular application.

Trigger Type Select whether the outbound port protocol is “TCP”, “UDP” or both.

Public Port Enter the In-coming (Inbound) port or port range for this type of

application (e.g. 2300-2400, 47624)

Note:

Individual port numbers are separated by a comma (e.g. 47624, 5775, 6541 etc.). To input

a port range use a “dash” to separate the two port number range (e.g. 2300-2400)

Public Type Select the Inbound port protocol type: “TCP”, “UDP” or both

Comment The description of this setting.

Please check www.sitecom.com for up to date drivers & utilities, manuals and support

Popular applications This section lists the more popular applications that require

multiple connections. Select an application from the Popular

Applications selection. Once you have selected an application,

select a location (1-10) in the Copy to selection box and then click

the button. This will automatically list the Public Ports Copy to

required for this popular application in the location (1-10) you’d

specified.

Add Special Application Fill in the "Trigger Port", "Trigger Type”, “Public Port”, "Public Type",

"Public Port" and "Comment" of the setting to be added and then

click "Add". Then this Special Application setting will be added into

the "Current Trigger-Port Table" below. If you find any typo before

adding it and want to retype again, just click "Clear" and the fields

will be cleared.

Remove If you want to remove some Special Application settings from the

“Current Trigger-Port Table", select the Special Application settings

you want to remove in the table and then click "Delete Selected". If

you want remove all Special Application settings from the table,

just click "Delete All" button. Click "Reset" will clear your current

selections.

Example: Special Applications

If you need to run applications that require multiple connections, then specify the port

(outbound) normally associated with that application in the "Trigger Port" field. Then select

the protocol type (TCP or UDP) and enter the public ports associated with the trigger port to

open them up for inbound traffic.

Example:

Trigger

Port

Trigger

Type Public Port Public Type Comment

1 28800 UDP 2300-2400, 47624 TCP MSN Game Zone

2 6112 UDP 6112 UDP Battle.net

In the example above, when a user trigger’s port 28800 (outbound) for MSN Game Zone then

the router will allow incoming packets for ports 2300-2400 and 47624 to be directed to that

user. Note: Only one LAN client can use a particular special application at a time.

Sitecom Wireless Network UMTS Router 54G WL-610

9.4 ALG Settings

You can select applications that need “Application Layer Gateway” to support.

Parameters Description

Enable You can select to enable “Application Layer Gateway”, then the router will

let that application correctly pass though the NAT gateway.

Please check www.sitecom.com for up to date drivers & utilities, manuals and support

9.5 UPnP Settings

With UPnP, all PCs in you Intranet will discover this router automatically. So you do not have

to do any configuration for your PC and can access the Internet through this router easily.

Parameters Default Description

UPnP Feature You can Enable or Disable UPnP feature here. After you Disable

enable the UPnP feature, all client systems that

support UPnP, like Windows XP, can discover this

router automatically and access the Internet through

this router without any configuration. The NAT

Traversal function provided by UPnP can let

applications that support UPnP smoothly connect to

Internet sites without any incompatibility problem due

to the NAPT port translation.

Sitecom Wireless Network UMTS Router 54G WL-610

9.6 QoS

The QoS can let you classify Internet application traffic by source/destination IP address and

port number. You can assign priority for each type of application and reserve bandwidth for

it. The packets of applications with higher priority will always go first. Lower priority

applications will get bandwidth after higher priority applications get enough bandwidth. This

can let you have a better experience in using critical real time services like Internet phone,

video conference …etc. All the applications not specified by you are classified as rule name

“Others”. The rule with a smaller priority number has a higher priority; the rule with a larger

priority number has a lower priority. You can adjust the priority of the rules by moving them

up or down.

Note:

If the total assigned bandwidth of higher priority applications is larger than the maximum

bandwidth provided by the WAN port, the other applications will not get any bandwidth.

Parameters Description

Enable/Disable QoS You can check “Enable QoS” to enable QoS function for the

WAN port. You also can uncheck “Enable QoS” to disable

QoS function for the WAN port.

Add a QoS rule into the table Click “Add” then you will enter a form of the QoS rule.

Click “Apply” after filling out the form and the rule will be

Please check www.sitecom.com for up to date drivers & utilities, manuals and support

added into the table.

Remove QoS rules from the table If you want to remove some QoS rules from the table,

select the QoS rules you want to remove in the table and

then click "Delete Selected". If you want remove all QoS

rules from the table, just click "Delete All" button. Click

"Reset" will clear your current selections.

Edit a QoS rule Select the rule you want to edit and click “Edit”, then you

will enter the detail form of the QoS rule. Click “Apply”

after editing the form and the rule will be saved.

Adjust QoS rule priority You can select the rule and click “Move Up” to make its

priority higher. You also can select the rule and click “Move

Down” to make its priority lower.

Edit QoS Rule:

You can assign packet classification criteria by its local IP range, remote IP range, traffic type,

protocol, local port range and remote port range parameters. The parameters that you leave

as blank will be ignored. The priority of this rule will be applied to packets that match

classification criteria of this rule. You can limit bandwidth consumed by packets that match

this rule or guarantee bandwidth required by packets that match this rule.

Parameters Description

Rule Name The name of this rule.

Bandwidth You can assign the download or upload bandwidth by the unit of Kbps

(1024 bit per second). You can limit the maximum bandwidth

consumed by this rule by selecting “Maximum”. You also can reserve

enough bandwidth for this rule by selecting “Guarantee”.

Local IP Address Enter the local IP address range of the packets that this rule will apply

to. If you assign 192.168.0.3 – 192.168.0.5, it means 3 IP addresses:

192.168.0.3, 192.168.0.4 and 192.168.0.5

Local Port Range Enter the local port range of the packets that this rule will apply to.

You can assign a single port number here or assign a range of port

numbers by assigning the first port number and the last port number

of the range. The two numbers are separated by a dash “-“, for

example “101-150” means from port number 100 to port number

150 – the range of 50 port numbers.

Remote IP Address Enter the remote IP address range of the packets that this rule will

apply to. If you assign 192.168.2.3 – 192.168.2.5, it means 3 IP

addresses: 192.168.2.3, 192.168.2.4 and 192.168.2.5

Remote Port Range Enter the remote port range of the packets that this rule will apply to.

Please check www.sitecom.com for up to date drivers & utilities, manuals and support

10 Toolbox

You can change the password required to log into the broadband router's system web-based

management. By default, there is no password. So please assign a password to the

Administrator as soon as possible, and store it in a safe place. Passwords can contain 0 to 12

alphanumeric characters, and are case sensitive.

Parameters Description

Current Password Enter your current password for the remote management

administrator to login to your Broadband router.

New Password Enter your new password

Confirmed Password Enter your new password again for verification purposes

Note:

If you forget your password, you’ll have to reset the router to the factory default (password

is admin) with the reset button (see router’s back panel).

Click < at the bottom of the screen to save the above configurations. You can now Apply>

configure other advance sections or start using the router (with the advance settings in

place)

Sitecom Wireless Network UMTS Router 54G WL-610

10.1 Timezone

The Time Zone allows your router to reference or base its time on the settings configured

here, which will affect functions such as Log entries and Firewall settings.

Parameter Description

Set Time Zone Select the time zone of the country you are currently in. The

router will set its time based on your selection.

Time Server Address The router default the “Time Server Address” is

“192.43.244.18”

Enable Daylight Savings The router can also take Daylight savings into account. If you

wish to use this function, you must check/tick the enable box

to enable your daylight saving configuration (below).

Start Daylight Savings Time Select the period in which you wish to start daylight Savings

Time

End Daylight Savings Time Select the period in which you wish to end daylight Savings

Time

Click < at the bottom of the screen to save the above configurations. You can now Apply>

configure other advance sections or start using the router (with the advance settings in place)

Please check www.sitecom.com for up to date drivers & utilities, manuals and support

10.2 Remote Management

The remote management function allows you to designate a host in the Internet the ability to

configure the Broadband router from a remote site. Enter the designated host IP Address in

the Host IP Address field.

Parameters Description

Host Address This is the IP address of the host in the Internet that will have

management/configuration access to the Broadband router from a remote

site. This means if you are at home and your home IP address has been

designated the Remote Management host IP address for this router

(located in your company office), then you are able to configure this router

from your home. If the Host Address is left 0.0.0.0 this means anyone can

access the router’s web-based configuration from a remote location,

providing they know the password.

Click the box to enable the Remote Management function. Enabled

Note:

When you want to access the web-based management from a remote site, you must enter

the router’s WAN IP address (e.g. 10.0.0.1) into your web-browser followed by port number

8080, e.g. 10.0.0.1:8080 (see below). You’ll also need to know the password set in the

Password Setting screen in order to access the router’s web-based management.

Sitecom Wireless Network UMTS Router 54G WL-610

Port The port number of remote management web interface.

Enabled Select “Enabled” to enable the remote management function.

Click < at the bottom of the screen to save the above configurations. You can now Apply>

configure other advance sections or start using the router (with the advance settings in

place)

Please check www.sitecom.com for up to date drivers & utilities, manuals and support

10.3 Firmware Upgrade

This page allows you to upgrade the router’s firmware.

Parameters Description

Firmware Upgrade This tool allows you to upgrade the Broadband router’s system

firmware. To upgrade the firmware of your Broadband router, you

need to download the firmware file to your local hard disk, and enter

that file name and path in the appropriate field on this page. You can

also use the Browse button to find the firmware file on your PC.

Once you’ve selected the new firmware file, click < at the bottom of the screen to Apply>

start the upgrade process. (You may have to wait a few minutes for the upgrade to complete).

Once the upgrade is complete you can start using the router.

Sitecom Wireless Network UMTS Router 54G WL-610

10.4 Backup Settings

The Backup screen allows you to save ( ) the router’s current configuration setting. Backup

Saving the configuration settings provides an added protection and convenience should

problems occur with the router and you have to reset to factory default. When you save the

configuration setting (Backup) you can re-load the saved configuration into the router

through the selection. If extreme problems occur you can use the Restore Restore to

Factory Defaults selection, this will set all configurations to its original default settings (e.g.

when you first purchased the router).

Parameters Description

Configuration Tools Use the " " tool to save the Broadband router current Backup

configuration to a file named "config.bin" on your PC. You can then

use the " " tool to restore the saved configuration to the Restore

Broadband router. Alternatively, you can use the "Restore to

Factory Defaults" tool to force the Broadband router to perform a

power reset and restore the original factory settings.

Please check www.sitecom.com for up to date drivers & utilities, manuals and support

10.5 Reset (restart) the router

You can reset the router’s system should any problem exist. The reset function essentially

Re-boots your router’s system.

Note:

Your settings will NOT be changed by the system-reboot.

Sitecom Wireless Network UMTS Router 54G WL-610

10.6 DDNS

DDNS allows you to map the static domain name to a dynamic IP address. You must get an

account, password and your static domain name from the DDNS service providers. This

router supports DynDNS, TZO and other common DDNS service providers.

Parameters Description

Enable/Disable Enable/Disable the DDNS function of this router

Provider Select a DDNS service provider

Domain name Your static domain name that use DDNS

Account/E-mail The account that your DDNS service provider assigned to you

Password/Key The password you set for the DDNS service account above

Click < at the bottom of the screen to save the above configurations. You can now Apply>

configure other advance sections or start using the router (with the advance settings in

place)

Please check www.sitecom.com for up to date drivers & utilities, manuals and support

Appendix A

How to manually find your PC’s IP and MAC address

1) In Window’s open the Command Prompt program

2) Type and <enter> ipconfig /all

• Your PC’s IP address is the one entitled IP address (e.g. 192.168.0.100)

• The router’s IP address is the one entitled Default Gateway (e.g. 192.168.0.1)

• Your PC’s MAC Address is the one entitled Physical Address (e.g.

00-13-D3-33-8D-45)

Sitecom Wireless Network UMTS Router 54G WL-610

Glossary

Default Gateway (Router): Every non-router IP device needs to configure a default

gateway’s IP address. When the device sends out an IP packet, if the destination is not on the

same network, the device has to send the packet to its default gateway, which will then send

it out towards the destination.

DHCP: Dynamic Host Configuration Protocol. This protocol automatically gives every

computer on your home network an IP address.

DNS Server IP Address: DNS stands for Domain Name System, which allows Internet

servers to have a domain name (such as www.Broadbandrouter.com) and one or more IP

addresses (such as 192.34.45.8). A DNS server keeps a database of Internet servers and

their respective domain names and IP addresses, so that when a domain name is requested

(as in typing "Broadbandrouter.com" into your Internet browser), the user is sent to the

proper IP address. The DNS server IP address used by the computers on your home network

is the location of the DNS server your ISP has assigned to you.

DSL Modem: DSL stands for Digital Subscriber Line. A DSL modem uses your existing phone

lines to transmit data at high speeds.

Ethernet: A standard for computer networks. Ethernet networks are connected by special

cables and hubs, and move data around at up to 10/100 million bits per second (Mbps).

Idle Timeout: Idle Timeout is designed so that after there is no traffic to the Internet for a

pre-configured amount of time, the connection will automatically be disconnected.

IP Address and Network (Subnet) Mask: IP stands for Internet Protocol. An IP address

consists of a series of four numbers separated by periods, that identifies a single, unique

Internet computer host in an IP network. Example: 192.168.0.1. It consists of 2 portions:

the IP network address, and the host identifier.

The IP address is a 32-bit binary pattern, which can be represented as four cascaded decimal

numbers separated by “.”: aaa.aaa.aaa.aaa, where each “aaa” can be anything from 000 to

255, or as four cascaded binary numbers separated by “.”:

bbbbbbbb.bbbbbbbb.bbbbbbbb.bbbbbbbb, where each “b” can either be 0 or 1.

A network mask is also a 32-bit binary pattern, and consists of consecutive leading

1’s followed by consecutive trailing 0’s, such as

11111111.11111111.11111111.00000000. Therefore sometimes a network mask can also

be described simply as “x” number of leading 1’s.

Please check www.sitecom.com for up to date drivers & utilities, manuals and support

When both are represented side by side in their binary forms, all bits in the IP address that

correspond to 1’s in the network mask become part of the IP network address, and the

remaining bits correspond to the host ID.

For example, if the IP address for a device is, in its binary form,

11011001.10110000.10010000.00000111, and if its network mask is,

11111111.11111111.11110000.00000000

It means the device’s network address is

11011001.10110000.10010000.00000000, and its host ID is,

00000000.00000000.00000000.00000111. This is a convenient and efficient method for

routers to route IP packets to their destination.

ISP Gateway Address: (see ISP for definition). The ISP Gateway Address is an IP address

for the Internet router located at the ISP's office.

ISP: Internet Service Provider. An ISP is a business that provides connectivity to the Internet

for individuals and other businesses or organizations.

LAN: Local Area Network. A LAN is a group of computers and devices connected together in

a relatively small area (such as a house or an office). Your home network is considered a LAN.

MAC Address: MAC stands for Media Access Control. A MAC address is the hardware

address of a device connected to a network. The MAC address is a unique identifier for a

device with an Ethernet interface. It is comprised of two parts: 3 bytes of data that

corresponds to the Manufacturer ID (unique for each manufacturer), plus 3 bytes that are

often used as the product’s serial number.

NAT: Network Address Translation. This process allows all of the computers on your home

network to use one IP address. Using the broadband router’s NAT capability, you can access

the Internet from any computer on your home network without having to purchase more IP

addresses from your ISP.

Port: Network Clients (LAN PC) uses port numbers to distinguish one network

application/protocol over another. Below is a list of common applications and protocol/port

numbers:

Application Protocol

Port Number

Telnet TCP 23

Produkt Specifikationer

Mærke:	Sitecom
Kategori:	Router
Model:	WL-610

Har du brug for hjælp?

Hvis du har brug for hjælp til Sitecom WL-610 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Router Sitecom Manualer

Sitecom AC750 WLR-5002UK Manual

2 Oktober 2024

Sitecom wl 607 wireless router 54g Manual

23 September 2024

Sitecom wl 611 300n router Manual

22 September 2024

Sitecom WL-535 Manual

19 September 2024

Sitecom dc 210 wired router Manual

19 September 2024

Sitecom WL-122 Manual

14 September 2024

Sitecom WL-540 Manual

29 August 2024

Sitecom WLR-5002 Manual

26 August 2024

Sitecom WL-114 V2 Manual

19 August 2024

Sitecom wireless network modem router mimo xr Manual

19 August 2024

Router Manualer

Nyeste Router Manualer

WyreStorm EXP-SW-0401-H2 Manual

22 Marts 2025

TP-Link Archer BE550 Pro Manual

9 Marts 2025

Devolo WiFi 6 Router 3600 5G LTE Manual

6 Marts 2025

Huawei E5785-320 Manual

23 Februar 2025

Huawei E5785-330 Manual

23 Februar 2025

Xiaomi Router AX3000T Manual

22 Februar 2025

Huawei E5180 Manual

20 Februar 2025

Digital Forecast Bridge RS 16*16 Manual

20 Februar 2025

Teltonika RUTM52 Manual

12 Februar 2025

Teltonika RUTM51 Manual

12 Februar 2025