Sky-Watcher SynScan Wi-Fi Adapter Manual
Sky-Watcher
Kamerastativ
SynScan Wi-Fi Adapter
Læs nedenfor 📖 manual på dansk for Sky-Watcher SynScan Wi-Fi Adapter (2 sider) i kategorien Kamerastativ. Denne guide var nyttig for 14 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/2
1. Connect to a Skywatcher Telescope Mount
Attach the SynScan Wi-Fi Adapter(RJ45 Jack) to the “Hand Control” port(RJ12 or RJ45
Jack) on the mount via:
• Supplied RJ12-to-RJ45 cable
• Supplied RJ45-to-RJ45 cable
• Original SynScan hand control cable
2. Connect to a Smartphone
1) Download the “SynScan” app from App Store or Google Play onto your smartphone.
2) Connect the adapter to a Skywatcher telescope mount and turn the power on.
3) Choose “SynScan_WiFi_####” in the Wi-Fi list available on your smartphone.
4) On an iOS device, wait up to 1 minute until the Wi-Fi icon appears in the notication
bar.
5) Open the SynScan app on your smartphone and tap on the “Connect” button at the
top, your SynScan App will setup connection to the adapter and the mount.
3. Congure the Adapter
In your SynScan app, tap Settings > WiFi Setting.
• Check “Modify Access Point” to
- Enable/Disable the Access Point Mode.
- Change the SSID(Name of the access point)
- Add or remove password for accessing the adapter’s Wi-Fi access point.
• Check “Modify Station” to
- Enable/Disable the Station Mode
- Enter the SSID of the Wi-Fi access point (router) to which the adapter will connect.
- Enter the password for the designated Wi-Fi access point (router).
- Enter a static IP. Note: This is not recommended for general users, using DHCP is prefered in most case.
Tap “Apply” button to conrm setting. You might need to restart the mount and/or
re-connect to the correct Wi-Fi network on your smartphone.
Important: In most case, users should use either “Access Point Mode” or “Station
Mode”, DONOT enable both of them.
4.Factory Reset
If you forget the password of the adapter’s access point, the adapter will need to be
reset to factory default for accessing.
The adapter can be reset to factory default after powered up and not accessed for 1
hour.
5. Using Access Point Mode or Station Mode
• is easier to use. Access Point Mode
• Station Mode needs extra conguration, but it:
- Allows a smart phone accessing to internet while controlling the telescope mount.
- Consumes less power.
Produkt Specifikationer
| Mærke: | Sky-Watcher |
| Kategori: | Kamerastativ |
| Model: | SynScan Wi-Fi Adapter |
Har du brug for hjælp?
Hvis du har brug for hjælp til Sky-Watcher SynScan Wi-Fi Adapter stil et spørgsmål nedenfor, og andre brugere vil svare dig
Kamerastativ Sky-Watcher Manualer
15 Juli 2024
Kamerastativ Manualer
- Kamerastativ SilverCrest
- Kamerastativ Sony
- Kamerastativ Braun
- Kamerastativ Easypix
- Kamerastativ Pyle
- Kamerastativ Hama
- Kamerastativ Laserliner
- Kamerastativ Bresser
- Kamerastativ Rollei
- Kamerastativ DJI
- Kamerastativ Swarovski
- Kamerastativ GoPro
- Kamerastativ Celestron
- Kamerastativ Zhiyun
- Kamerastativ Rode
- Kamerastativ Sachtler
- Kamerastativ Arkon
- Kamerastativ Ravelli
- Kamerastativ Freefly
- Kamerastativ Proaim
- Kamerastativ Manfrotto
- Kamerastativ Joby
- Kamerastativ Magnus
- Kamerastativ Neewer
- Kamerastativ Easyrig
- Kamerastativ Sevenoak
- Kamerastativ Miller
- Kamerastativ Square Jellyfish
- Kamerastativ SmallRig
- Kamerastativ Robus
- Kamerastativ Sunpak
- Kamerastativ Libec
- Kamerastativ Celly
- Kamerastativ Velbon
- Kamerastativ Auray
- Kamerastativ Stalco
- Kamerastativ Vanguard
- Kamerastativ IOptron
- Kamerastativ E-Image
Nyeste Kamerastativ Manualer
20 November 2024
17 November 2024
17 November 2024
17 November 2024
19 Oktober 2024
18 Oktober 2024
24 September 2024
5 September 2024
5 September 2024
5 September 2024