Sony DC-VQ11 Manual

Sony Batterioplader DC-VQ11

Læs nedenfor 📖 manual på dansk for Sony DC-VQ11 (4 sider) i kategorien Batterioplader. Denne guide var nyttig for 22 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/4

Fuse Replacement

If this unit is not working properly, check to see if the fuse has blown out.

If the fuse has blown out, replace it in the following way.

1 Twist the end of the plug and remove it.

2 Remove the blown out fuse.

3 Insert the new fuse and twist the end of the plug and tighten.

Notes

• Replace the fuse with a fuse of the same rating (4 A, 125 V).

• If the car’s cigarette lighter socket is dirty with ash, etc., the plug part will

become hot due to a poor connection. Be sure to clean it before using.

• When replacing the fuse, do not substitute anything for the specified fuse.

• If the fuse blows again soon after replacement, consult your nearest Sony

dealer.

Please contact your car dealer about the polarity that your car is grounded

or the voltage of your car battery, etc.

When the CHARGE lamp flashes

If a problem occurs during charging, the CHARGE lamp flashes and

WARNING appears on the display.

Check through the following chart.

To remove the battery pack

Slide the battery pack in the direction of the arrow,then lift it straight out.

To Check Charging

While charging, you can check the charging time on the display. After

starting charging in a minute, BATTERY LIFE lights up on the display.

Press DISPLAY CHANGE while charging.

Each time you press DISPLAY CHANGE, the display changes as follows.

Notes

• The time display shows the approximate time when charging at 10°C -

30°C. The time display may differ from the actual charging time

depending on using conditions and circumstances.

• The time display may show “– – – –” in the following cases. However, the

unit is not malfunctioning.

– The remaining battery time is less than 5 minutes.

– There is a difference between the displayed time and actual charging

time. Even if this happens, continue charging.

• Full charge requires about 1 hour after normal charge is completed. If you

remove the battery pack between normal charge and full charge, the

charging time may not be displayed properly in the next charging.

• If the charging time is not displayed properly, fully charge the battery

pack. The charging time will be displayed properly.

• When you attach a fully charged battery pack to this unit, “TIME TO CHG

FULL 1h” may appear on the display. However, the unit is not

malfunctioning.

• The remaining battery time may not be displayed depending on using

conditions and circumstances of your video camera recorder and of the

battery. See “About the remaining time” for more details.

• You may wait for a while after pressing DISPLAY CHANGE until the

display shows the time indication.

• To display the remaining battery time of a new battery, attach it to your

video camera recorder and use it for about 20 seconds. Then, charge the

battery with this unit.

To Operate Video Equipment

See illustration .C

Use the supplied DK-115 connecting cord.

For details of the connection, refer to the instruction manual of your video

equipment.

1 Set the mode change switch to VCR/CAMERA.

2 Connect the DC cord to the cigarette lighter socket.

3 Connect the connecting cord to the DC OUT connector of thisA

unit.

4 Connect the connecting plate to the video equipment.B

When using the connecting cord

While pressing the connecting plate , slide it to the left.B

To remove the connecting plate, slide it to the right while sliding the

battery release lever to the right.C

Notes

• If you set the mode change switch to CHARGE while operating the video

equipment, the power supply to the video equipment stops.

• You cannot charge the battery pack attached to this unit while supplying

the power to the video equipment.

• Keep this unit away from the video equipment if the picture is disturbed.

English

Specifications

Power requirements 12/24 V DC

(12/24 V, only for negative groundedcars)

Output voltage DC OUT:

4.2 V, 1.8 A in operating mode

Battery charge terminal:

4.2 V, 1.5 A in charge mode

Application Sony battery pack NP-FS11/FS21/FS31/F10/

F20/F30

Operating temperature 0°C to 40°C (32°F to 104°F)

Storage temperature –20°C to 60°C (–4°F to 140°F)

Dimensions Approx. 85 × × 45 79 mm (w/h/d)

(33/8 1×13/16 3 ×1/8 inches)

including projecting parts

Mass Approx. 240 g (8.0 oz)

Supplied accessories Connecting cord DK-115 (1)

Design and specifications are subject to change without notice.

This mark indicates that this product is a genuine

accessory for Sony video products. When purchasing

Sony video products, Sony recommends that you

purchase accessories with this “GENUINE VIDEO

ACCESSORIES” mark.

Identifying the parts

See illustration .A

1Mode change switch

2CHARGE lamp

3DISPLAY CHANGE button

4DC OUT connector

5Terminal shutter

6Display window

Display window

7“InfoLITHIUM” indicator

8WARNING indicator

9TIME TO CHG (charge) indicator

q; Time indicator

qa BATTERY LIFE (battery remaining time) indicator

qs VCR/CAMERA indicator

qd Full charge indicator

qf Remaining battery indicator

To Charge the Battery Pack

See illustration .B

1 Set the mode change switch to CHARGE.

2 Connect the power cord to the cigarette lighter socket.

The beep sounds and the display window lights up.

3 Install the battery pack.

Charging begins. When the remaining battery indicator becomes

and the CHARGE lamp lights up, normal charge is completed. For full

charge, which allows you to use the battery slightly longer than “normal

charge”, leave the battery pack attached until the CHARGE lamp goes

out.

Remove the battery pack when required. It can be used even if the

charging is not completed.

Remaining battery indicator

Normal charge Full charge

To Install the battery pack

1 Place the battery pack on this unit with the

b b

b mark facing the

terminal shutter.

2 Slide the battery pack in the direction of the arrow.

Press the battery pack until the terminal shutter enters completely into

this unit.

Note

When you install the battery pack, be sure not to strike it to the terminal of

the DC adaptor/charger.

Charging time

The following table shows the charging time for the battery pack which is

discharged completely.

• Approximate minutes to charge an empty battery pack fully ( ).Full charge

• Approximate minutes in parentheses indicate the time when you charge

normally ( ).Normal charge

• To ascertain the battery life, refer to the instruction manual of the video

equipment which you use.

• The charging time may differ depending on the condition of the battery

pack or the temperature of the environment.

Notes

• When the mode change switch is set to VCR/CAMERA during charging,

charging stops.

• If the CHARGE lamp does not light or flash, check that the battery pack is

correctly attached to the DC adaptor/charger. If it is not attached, it will

not be charged.

Battery pack Charging time

NP-F10 105 (45)

NP-F20 135 (75)

NP-F30 165 (105)

Battery pack Charging time

NP-FS11 110 (50)

NP-FS21 150 (90)

NP-FS31 195 (135)

Thank you for purchasing the Sony DC adaptor/charger.

Before operating the unit, please read this manual thoroughly and retain it

for future reference.

The DC-VQ11 car battery charger (only for negative (–) grounded cars) can

be used by connecting to the cigarette lighter socket of a car as follows:

• to charge a lithium ion type battery pack.

The following functions are available with the “InfoLITHIUM” battery

pack:

– Quickly charging

– Remaining charge time display and remaining battery time display

• to supply power to the Sony video equipment using the connecting cord

(supplied).

What is the “InfoLITHIUM”

The “InfoLITHIUM” is a lithium ion battery pack which can exchange data

with compatible electronic equipment about its battery consumption. Sony

recommends that you use the “InfoLITHIUM” battery pack with electronic

equipment having the mark.

“InfoLITHIUM” is a trademark of Sony Corporation.

WARNING

To prevent fire or shock hazard, do not expose the unit to rain or moisture.

To avoid electrical shock, do not open the cabinet.

Refer servicing to qualified personnel only.

Notes on Use

About the remaining battery time

While charging the battery pack, this unit will show the remaining battery

time with your video equipment, etc. on the following conditions.

• Using the “InfoLITHIUM” battery pack

• Using the electronic equipment having the mark

Make sure that you use the battery pack having the mark.

Consult the operating instructions supplied with your video equipment if it

is applied to “InfoLITHIUM”.

If you use this battery pack with electronic equipment not having the

mark, the remaining battery capacity will not be indicated in minutes.*

* The indication may not be accurate depending on the condition and environment

which the equipment is used under

Charging

Use only a lithium ion type battery pack. This unit cannot be used to charge

a Ni-Cd/Nickel hydrogen type battery pack.

• Attach the battery pack firmly.

• Charge the battery pack on a flat surface without vibration.

Charging temperature

The temperature range for charging is 0°C to 40°C (32°F to 104°F).

However, to provide maximum battery efficiency, the recommended

temperature range when charging is 10°C to 30°C (50°F to 86°F).

Others

• Use this car battery charger only for cars which use a 12 or 24 volt battery.

• There are cars which are negatively grounded and there are others which

are positively grounded.

This car battery charger is for negatively grounded cars only.

• Use the unit with leaving the car engine going. If you use the unit with the

car engine stopped, the car battery may become unusable.

• This unit is not disconnected form the power source as long as it is

connected to the cigarette lighter socket of a car.

• Unplug the car battery cord from the cigarette lighter socket when not in

use. To disconnect the cord, pull it out by the plug. Never pull the cord

itself.

• Do not operate the unit with a damaged cord or if it has been dropped or

damaged.

• Be sure that nothing metallic comes into contact with the metal parts of

the unit or connecting plate. If it does, a short may occur and the unit may

be damaged.

• Always keep the metal contacts clean.

• Do not disassemble or convert the unit.

• Do not apply mechanical shock or drop the unit.

• While the unit is in use, it gets warm. But this is normal.

• Keep the unit away from AM receivers, because it will disturb AM

reception.

• When charging the battery pack, attach the battery pack to the unit firmly.

• Attach the battery pack to the unit straight. If the battery pack is not

installed in an appropriate position, the jack part of the unit may be

damaged.

• To protect the battery pack, remove the battery pack from the unit within

24 hours after the charging is completed.

• Do not place the unit in a location where it will be in direct sunlight such

as on the dashboard.

If any difficulty should arise, unplug the unit and contact your nearest Sony

dealer.

• The remaining time until

normal charge is completed

• The time is not displayed after

normal charge is completed

•The remaining battery time

when the battery pack being

charged is attached to your

“InfoLITHIUM” electronic

equipment

The time is not displayed when the

remaining battery time is less than 5

minutes.

• The remaining time until full

charge is completed

• The time is not displayed after

full charge is completed

WARNING

To prevent fire or shock hazard, do not

expose the unit to rain or moisture.

CAUTION

You are cautioned that any changes or modifications not expressly

approved in this manual could void your authority to operate this

equipment.

Note:

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio

communications.

However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

Owner’s Record

The model and serial numbers are located on the bottom of the unit.

Record the serial number in the space provided below.

Refer to these numbers whenever you call upon your Sony dealer regarding

this product.

Model No. DC-VQ11 Serial No.

DC Adaptor/Charger

Operating Instructions

Mode d’emploi

Manual de instrucciones

3-058-917- (1)11

DC-VQ11

To remove

WARNING BATTERY LIFE

TIME TO CHG

NORMAL FULL h m

VCR/CAMERA

DISPLAY

CHANGE

DISPLAY

CHANGE

DISPLAY

CHANGE

BATTERY LIFE

TIME TO CHG

NORMAL m

TIME TO CHG

FULL h m

Please contact your nearest Sony dealer in connection with the product

with the problem.

Remove the battery pack from this unit, then install the same battery

pack again.

If the CHARGE lamp flashes

again:

Install another battery pack.

If the CHARGE lamp lights and

does not flash again:

If the CHARGE lamp goes out

because the charging time has

passed, there is no problem.

If the CHARGE lamp flashes

again:

The problem is with this unit.

If the CHARGE lamp lights and

does not flash again:

If the CHARGE lamp goes out

because the charging time has

passed, the problem is with the

battery pack first installed.

Produkt Specifikationer

Mærke:	Sony
Kategori:	Batterioplader
Model:	DC-VQ11
Vægt:	240 g
Opbevaringstemperatur (T-T):	-20 - 60 °C
Driftstemperatur (T-T):	0 - 40 °C
Dimensioner (BxDxH):	85 x 45 x 79 mm
Udgangsspænding:	12 V