Sony DCC-FMT3 Manual

Sony Ikke kategoriseret DCC-FMT3

Læs nedenfor 📖 manual på dansk for Sony DCC-FMT3 (4 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 4 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/4

2Connect the stereo mini plug to the headphone jack on the portable

audio device.

If your portable audio device has separate settings for headphone and LINE

OUT, set the portable audio device to the headphone setting. Sound may be

distorted if it is connected to LINE OUT.

3Insert this transmitter (this unit) into the cigarette lighter socket.

4Start playback on the portable audio device.

Notes

• Do not activate any bass boost or equalizer function on the portable audio

device. Refer to the operating instructions supplied with the portable audio

device.

• Set the volume control of the portable audio device as high as possible, but

not so high that the audio signal becomes distorted. If sound is still low,

turn the volume up on the car radio.

5Route the antenna cable inside the car for best audio reception from

this unit.

The method to install the antenna cable will depend on your car

type. Find the position that provides the best reception, and then

install the cable.

<Example of installation in a car with its FM radio antenna built-

in the rear window, or its rod antenna mounted on the rear of the

car body>

Notes

• Route the antenna cable close to the car antenna. This may help to improve

the reception from this unit.

• For details about the car radio antenna, refer to the car operating

instructions.

About the antenna cable magnet

The antenna cable is supplied with a magnet attached at the end. It

is used to anchor the cable to a metal part of the car, such as a

passenger’s seat rail (see illustration below). The magnet at the end

of the antenna cable is to anchor the antenna’s best reception

position and prevents it being moved, for example, when

passengers get in or out of the car.

To use the antenna cable magnet, do the following.

1Route the antenna cable where the best reception from this unit is

obtained.

2Attach the magnet at the end of the antenna cable to a metal part of the

car, such as a passenger’s seat rail, to anchor the antenna cable in place

(see illustration below).

<Example of attaching the antenna cable magnet to a passen-

ger’s seat rail>

Use the above basic example as a general guideline. Adjust the antenna for

the best reception, depending on your car.

3If the reception from this unit becomes worse after attaching the magnet at

the end of the antenna cable to a passenger’s seat rail, etc., in step 2,

revert to a previous position (to best reception) in step 1, without using

the magnet (without attaching it to a passenger’s seat rail, etc.).

Notes

• Be careful to line the cable so that it will not interfere with driving, become

entangled with passenger movements, or be damaged by seat adjustments,

etc.

• If the magnet is attached near movable objects, such as doors or seat rails,

make sure that the antenna cable does not become entangled. This may

cause the wire to break.

• Do not leave floppy disks or personal credit cards with magnetic coding

near the antenna cable magnet.

2-636-433- (2)11

Operating Instructions

Mode d’emploi

Manual de instrucciones

Car FM Stereo

Transmitter

DCC-FMT3

For customers who purchased this product in the USA

Please register this product on line at

http://www.sony.com/productregistration.

Proper registration will enable us to send you periodic mailings about new

products, services, and other important announcements.

Registering your product will also allow us to contact you in the unlikely

event that the product needs adjustment or modification. Thank you.

English

WARNING

To reduce the risk of fire or electric shock, do not expose this

apparatus to rain or moisture.

To avoid electrical shock, do not open the cabinet. Refer servicing to qualified

personnel only.

Do not install the appliance in a confined space, such as a bookcase or built-in

cabinet.

To reduce the risk of fire or electric shock, do not place objects filled with

liquids, such as vases, on the apparatus.

You are cautioned that any changes or modifications not expressly approved in

this manual could void your authority to operate this equipment.

Note

This device complies with Part 15 of the FCC rules and RSS-210 of the IC rules.

Operation is subject to the following two conditions: (1) this device may not

cause interference, and (2) this device must accept any interference, including

interference that may cause undesired operation of the device.

If the reception from this unit declines

If the reception from this unit declines, even though it was good at the frequency

set in the beginning, solve the problem referring to the following remedies,

according to your circumstances.

After setup, reception from this unit declines while driving.

c FM broadcast reception may be poor in certain locations, such as

underground parking, behind tall buildings, etc. If the car radio and this unit

were set up in such a location; due to poor FM broadcast reception, the

frequency you set for this unit may be already occupied. If so, the occupying

FM broadcast station is received when its reception conditions improve (as

you drive) resulting in interference with this unit’s same set frequency. In

this case, reset the car radio and this unit to another open frequency in a

location where the FM broadcast reception is better.

Reception from this unit is disrupted when you move to a new

location.

c FM broadcast reception conditions vary from one location to another. After

setting an open frequency in one location, as you move to other areas, that

frequency may become occupied by a broadcast station’s signal. In this case,

reset the frequency on both the car radio and this unit to another open

frequency.

Interference or noise occurs.

c Other FM broadcasts or non-licensed broadcastings in a city area may

interfere with the reception of the frequency set for this unit. In this case, set

the car radio and this unit to a less-influenced frequency.

Notes

• Do not attempt to connect this unit, or to operate this unit, a portable audio

device, or a car radio while driving or waiting at a traffic signal. Park in a safe

place first.

• Plug securely into the cigarette lighter socket.

• This unit may not fit, depending on the location or shape of the cigarette lighter

socket.

• Route the antenna cable and the audio cable (with the stereo mini plug at its

end) in a manner that does not interfere with your driving, and is out of the

reach of children.

• Install this unit in a manner that will not hinder the airbag function in an

emergency.

Fuse replacement

If this unit does not work correctly, check the fuse in the cigarette lighter plug.

If the fuse is blown, replace it.

1Pull this unit out of the cigarette lighter socket.

2Detach the end of the plug by turning it counter-clockwise.

3Take out the fuse.

4Check the fuse.

If the fuse is blown, go to Step 5.

If no fuse is blown, go to Step 6.

5Install a new fuse.

Use a fuse of the correct amperage, as stated on the fuse compartment of this

unit (1 A, 125 V, 20 mm).

6Insert the fuse.

7Reattach the end of the plug by turning it clockwise firmly.

Notes

• Use of a higher amperage fuse may cause serious damage or fire.

• Do not use a piece of wire instead of a fuse.

• If the replaced fuse blows again, consult your dealer.

Precautions

• Do not attempt to connect this unit, or to operate this unit, a portable audio

device, or a car radio while driving or waiting at a traffic signal. Park in a safe

place first.

• Unplug this unit from the cigarette lighter socket whenever the engine of the

car is not running. Depending on the car type, even if the ignition key is off, the

power supply may not turn off automatically. In this case, this may cause

unnecessary car battery consumption.

• When not in use, unplug this unit from the cigarette lighter socket and store in a

safe place where it will not interfere with your driving or become entangled in

parts of the car interior (seat, door, etc.).

• Be sure to fully secure the portable audio device connected to the unit to avoid

moving when braking.

• Route the antenna cable or signal cable properly so that they will not interfere

with your driving or become entangled in parts of the car interior (seat, door,

etc.).

• Never yank or pull the antenna cable or signal cable. This may cause

malfunctions or wire breaks.

• Do not drop or hit the unit. This may cause malfunctions.

• This unit may become warm while using. This is not a malfunction.

Troubleshooting

Should any problem persist after you have made the following checks, consult

your nearest Sony dealer.

There is no sound from the portable audio device to the car radio.

❒This unit is not fully plugged into the cigarette lighter socket.

c Insert this unit correctly and securely.

❒This unit is not fully connected to the portable audio device.

c Connect this unit correctly and securely.

❒The transmission frequency of the unit and the FM car radio do not coincide.

c Set both the unit and the FM car radio to the same frequency.

❒There is no sound from the connecting portable audio device.

c Start playback on the portable audio device.

c Set the volume control of the portable audio device as high as possible but

not so high that the audio signal becomes distorted.

The volume is low.

❒The volume of the portable audio device is set too low.

c Set the volume control of the portable audio device as high as possible but

not so high that the audio signal becomes distorted.

If sound is still low, turn the volume up on the car radio.

The sound is distorted.

❒The input signal is too high.

c If you connected to the LINE OUT jack on the portable audio device,

disconnect and reconnect to the headphone jack.

❒The bass boost function on the portable audio device is on.

c Cancel the bass boost function.

Noise is generated.

❒The frequency of the unit does not coincide with the FM car radio.

c Set the unit and the FM car radio to the same frequency.

❒The reception from this unit is not good.

c Route the antenna cable for the unit inside the car. Position the antenna close

to the car antenna, or stabilize the antenna cable with the magnet to the

passenger’s seat rail, and so on. This may help to improve the reception

from this unit.

❒The FM car radio receives a broadcast signal.

c Select an empty frequency (a non-broadcast frequency, indicated by a static

hissing sound).

❒The selected frequency is occupied or the signal is jammed.

c Select another open or frequency which is less influenced by jamming (a

non-broadcast frequency, indicated by a static hissing sound).

The sound is interrupted.

❒The signal is jammed locally.

c Select another frequency which is less influenced by jamming (a non-

broadcast frequency, indicated by a static hissing sound).

The POWER lamp does not light.

❒This unit is not completely plugged into the cigarette lighter socket.

c Insert this unit correctly and securely.

❒Depending on the car type, the engine must be started for electric current to

flow to the cigarette lighter socket.

c Start the engine.

❒The fuse is blown.

c Replace the fuse.

Fuse

Cigarette lighter

plug

End of the

plug

to tighten

to remove

Portable audio

device

AVERTISSEMENT

Pour éviter tout risque d’incendie ou de choc électrique, n’exposez

pas l’appareil à la pluie ou à l’humidité.

Pour éviter tout choc électrique, n’ouvrez pas le boîtier. Confiez l’entretien à un

technicien qualifié exclusivement.

N’installez pas l’appareil dans un espace confiné, tel qu’une bibliothèque ou une

armoire encastrée.

Pour éviter tout risque d’incendie ou de choc électrique, ne placez pas d’objets

remplis de liquide, tels que des vases, sur l’appareil.

Nous vous mettons en garde contre le fait que tout changement ou modification

non expressément approuvé dans le présent manuel peut invalider votre droit à

utiliser cet appareil.

Remarque

Cet appareil est conforme à la partie 15 de la réglementation FCC et à la règle IC

RSS-210.

Son utilisation est autorisée seulement aux conditions suivantes : (1) il ne doit pas

produire de brouillage et (2) l’utilisateur du dispositif doit être prêt à accepter tout

brouillage radioeléctrique reçu, même si ce brouillage est susceptible de

compromettre le fonctionnement du dispositif.

Caractéristiques

Cet appareil vous permet d’écouter des programmes avec des appareils audio

portables par l’intermédiaire d’un autoradio FM. La musique provenant d’appareils

portables tels qu’un lecteur HDD, une mémoire flash, un MD ou CD

WALKMAN*, etc., est transmise à l’autoradio du véhicule par les ondes radio FM.

Son clair et stable

• Avec le câble d’antenne émetteur flexible, il est possible de transmettre une onde

radio FM stable dans n’importe quelle voiture. Le câble d’antenne émetteur flexible

dispose d’un aimant permettant de le relier à une partie métallique de la voiture.

• Une sélection numérique des fréquences, au lieu d’une sélection analogique,

permet une transmission plus stable et claire.

Utilisation facile grâce à la molette de sélection des fréquences

Choix de 12 fréquences radio FM (canaux) pour la transmission.

Format compact

Le format compact de cet appareil vous permet de l’utiliser sur l’allume-cigare.

Il est conçu de sorte à ne présenter une partie saillante que dans une direction,

ainsi lorsqu’il est installé, il peut être pivoté afin de n’occasionner aucune gêne

autour de l’allume-cigare.

Pas de piles sèches

Cet appareil se branche sur une batterie de voiture 12 V ou 24 V CC (allume-

cigare) disponible dans la majorité des voitures et camions.

* « WALKMAN » est une marque déposée par Sony Corporation pour

représenter les produits stéréo dotés d’écouteurs.

Identification des pièces

Raccordements

Réglez l’autoradio

1Réglez votre autoradio à FM.

2Sélectionnez un canal dont la réception des émissions FM est

médiocre dans la liste ci-dessous.

88,1 MHz, 88,3 MHz, 88,5 MHz, 88,7 MHz, 88,9 MHz, 106,7 MHz,

106,9 MHz, 107,1 MHz, 107,3 MHz, 107,5 MHz, 107,7 MHz, 107,9 MHz

Les conditions de réception FM peuvent changer au fur et à mesure que vous

vous déplacez. Si la fréquence sélectionnée devient occupée par un signal

d’émission, sélectionnez une autre fréquence libre.

Remarques

• Pour plus de détails sur les réglages de l’autoradio, reportez-vous au mode

d’emploi de celui-ci.

• Baissez le volume avant de régler l’autoradio.

Installez l’appareil

1Faites tourner la molette de sélection des fréquences pour

sélectionner la même fréquence que celle réglée sur l’autoradio.

La fréquence sélectionnée s’affiche dans la fenêtre d’affichage des

fréquences. La marque apparaît au point de transition entre une bande

basse fréquence (88,1 MHz~88,9 MHz) et une bande haute fréquence

(106,7 MHz~107,9 MHz).

La marque représente une limite entre les hautes fréquences et les basses fréquences.

2Raccordez la minifiche stéréo à la prise casque de l’appareil audio

portable.

Si votre appareil audio portable présente des réglages différents pour le

casque et pour LINE OUT, réglez l’appareil audio portable au même réglage

que le casque. Le son peut être déformé s’il est connecté à LINE OUT.

3Insérez cet émetteur (cet appareil) dans l’allume-cigare.

Voyant POWER

Câble

d’antenne

Fenêtre d’affichage

des fréquences

Molette de sélection

des fréquences

Minifiche stéréo

Français

Appareil audio

portable

Portable audio

device

to a cigarette

lighter socket

Magnet

Seat rail

Portable audio

device

Aimant

Features

With this unit, you can enjoy listening to audio played on portable audio devices

through a car FM radio. Music from portable audio devices such as an HDD,

flash memory, MD or CD WALKMAN*, etc., is transmitted to the car’s FM

radio via FM radio waves.

Stable clear sound

• Using the flexible transmitting antenna cable, it is possible to transmit a stable

FM radio wave in any kind of car. The flexible transmitting antenna cable has a

magnet to anchor itself to a metal part inside the car.

• Digital frequency selection, rather than analog, assures a more stable and clear

transmission.

Easy operation with the frequency select dial

Select from 12 FM radio frequencies (channels) to transmit.

Compact design

The small design of this unit allows it to be used in the cigarette lighter socket.

This unit is designed so as its protruding part is in one direction only, and when

installed can be rotated in order to avoid any obstructions around the cigarette

lighter socket.

No dry batteries

This unit connects to a 12 V or 24 V DC car battery (cigarette lighter socket),

available in many types of cars and trucks.

*“WALKMAN” is a registered trademark of Sony Corporation to represent

Headphone Stereo products.

Identifying the parts

Connections

Set the car radio

1Set your car radio to FM.

2Select a channel that does not get good FM broadcast reception

from the list below.

88.1 MHz, 88.3 MHz, 88.5 MHz, 88.7 MHz, 88.9 MHz, 106.7 MHz,

106.9 MHz, 107.1 MHz, 107.3 MHz, 107.5 MHz, 107.7 MHz, 107.9 MHz

The FM broadcast reception conditions may change as your location changes.

If the selected frequency becomes occupied by a broadcast signal, select

another open frequency.

Notes

• For details about car radio settings, refer to the car radio operating instructions.

• Turn the car radio volume down before setting the car radio.

Install the unit

1Rotate the frequency select dial to select the same frequency that

you set on the car radio.

The selected frequency appears in the frequency display window. The

mark appears at the transition point between a low frequency band

(88.1 MHz~88.9 MHz) and a high frequency band (106.7 MHz~107.9 MHz).

The mark is a border between high frequency and low frequency.

Frequency select dial

POWER lamp

Magnet

Antenna cable

Stereo mini plug

Frequency display

window

(Suite à la page suivante)

This warranty is valid only in the United States.

Antenna cable

Specifications

Transmission system

multiplex stereo

Transmission frequency

88.1 MHz, 88.3 MHz, 88.5 MHz, 88.7 MHz, 88.9 MHz, 106.7 MHz,

106.9 MHz, 107.1 MHz, 107.3 MHz, 107.5 MHz, 107.7 MHz, 107.9 MHz

Electric strength

less than 250 µV/m (3 m)

Power voltage

DC 12/24 V (only for negative grounded cars)#

Input

ø3.5 mm (stereo mini plug)

Dimensions

Signal cable length

Approx.1 m (3.3 ft)

Antenna cable length

Approx.1.5 m (4.9 ft)

Mass

Approx. 40 g (1.42 oz) (without cables)

Supplied accessories

Operating Instructions (1)

Design and specifications are subject to change without notice.

Unit: mm

123

vers un allume-cigare

Appareil audio

portable

Produkt Specifikationer

Mærke:	Sony
Kategori:	Ikke kategoriseret
Model:	DCC-FMT3

Har du brug for hjælp?

Hvis du har brug for hjælp til Sony DCC-FMT3 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Sony Manualer

11 Oktober 2024

11 Oktober 2024

11 Oktober 2024

11 Oktober 2024

11 Oktober 2024

11 Oktober 2024

11 Oktober 2024

10 Oktober 2024

10 Oktober 2024

1 Oktober 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Elektron Overbridge Manual

26 November 2024

Elektron Sidstation Manual

26 November 2024

SKROSS World Adapter Pro+ Manual

26 November 2024

SKROSS PRO – World & USB Manual

26 November 2024

SoundTube IPD-RS82-EZ Manual

26 November 2024

Kramer 4x1VB Manual

26 November 2024

Kramer RC-63A Manual

26 November 2024

SoundTube IPD-HP82-EZ Manual

26 November 2024

Kramer RK-KVM-1U-PP3 Manual

26 November 2024

Gioteck VX-2 (PS3) Manual

26 November 2024