Sony RM-EZ4 Manual

Sony Fjernbetjening RM-EZ4

Læs nedenfor 📖 manual på dansk for Sony RM-EZ4 (3 sider) i kategorien Fjernbetjening. Denne guide var nyttig for 26 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/3

Searching for the Correct Code

It is possible to find a code number available

for a component that does not have one in

“ ”Component code numbers.

Before starting the Search function

Set each component to the following status so

that the Search function works effectively.

TV, DVD Home Theater: Power-on

Other components: Power-off

* If any of these components are assigned to any

of the Component Select buttons, you can set a

component code using the Search function.

1 SETPress and hold for more than two seconds. The SET indicator

lights up.

2 Press the appropriate Component Select button. The SET indicator

lights up.

3 Press CH + (or CH –) and 1 in turn until the component reacts as

follows:

TV: Power-off

Other components: Power-on

Press CH + to go to the next code number.

Press CH – to go back to the previous code number.

The SET indicator flashes once after the numbers have cycled

once.

One cycle means, for example, that the commander has finished

searching for all the code numbers allocated to the component.

4 ENTPress .

The SET indicator and the Component button turn off.

If the SET indicator flashes five times before turning off, setup is

incomplete. Start over from Step 3.

If the component does not operate properly, repeat steps 1 to 4 and

search for another code.

If you still cannot get the Commander to work properly, see

“ ”Troubleshooting.

Installing the batteries

Push open the battery compartment and insert two size AA (R6)

batteries (not supplied).

Be sure to align the + and – on the batteries with the + and – in the

battery compartment.

1 2

When to replace the batteries

Before replacing the batteries, have new ones ready beforehand.

Under normal conditions, batteries will last up to one year. If the Commander

does not operate properly, the batteries might be worn out. Replace the

batteries with new ones.

Notes

• Replace both batteries with new ones.

• Do not take more than to replace the batteries; otherwise, your3 minutes

code number settings will be erased.

•

Do not mix old batteries with new ones, or mix different battery types together.

• If the electrolyte inside the battery should leak, wipe the contaminated area of

the battery compartment with a cloth and replace the old batteries with new

ones. To prevent the electrolyte from leaking, remove the batteries when you

plan to not use the Commander for a long period of time.

Specifications

Operable distance Approx. 7 m (23 ft) (varies depending on component

manufacturer)

Power requirements Two size AA (R6) batteries (not supplied)

Battery life Approx. 1 year (varies depending on frequency of

button use - up to approx. 300 times per day)

Dimensions Approx. 63 × 149 × 30 mm (w/h/d)

(2 1/ 5 2×7/ 8× 1 3/16 in)

Mass Approx. 86 g (3.0 oz) (not including batteries)

Design and specifications are subject to change without notice.

Operating a TV

Operating a digital satellite receiver

2 To switch the output of the digital satellite receiver to the TV. (When

you connect a TV cable or antenna to the receiver, the output switches

between TV and satellite programs.)

3 4 9, and

To change the channel.

q; CH +: Channel up.

CH –: Channel down.

qa To tune to the last tuned station.

Operating a cable box

2 To change the input mode.

3 4 9, and

To change the channel.

q; CH +: Channel up.

CH –: Channel down.

qa To toggle the current/previous channel.

Continued on reverse side / Continúa en el reverso

About tactile dots

The number button and each have a tactile dot for convenient use.5 CH +

Note on the VOL +/– and MUTING buttons

The Commander controls or mutes the TV’s volume when you select a visual

component. The Commander outputs the signals to control or to mute the TV

volume when you have set one of these components.

Notes

• In some cases, you can turn the cable box on/off by pressing CH + or CH – on

the Commander.

• If your cable box can control volume, be sure to set its volume control to a

moderate level. If the volume on the cable box is turned down completely,

you will not be able to adjust your TV’s volume with the Commander.

SET indicator

Cable box / Adaptadores para cablevisión

Brand / Marca Code No. / N.º código

Sony 3101

ABC 9405

Adelphia 3107, 3110

Advanced Newhouse 3107

Altrio 3107

Americast 3105

Atlantic Broadband 3107

Bell South 3105

Blue Ridge 3107

Brigth House 3107

Cablevision 3107

Charter 3107

Comcast 3107

Cox 3107

General Instrument 3103, 9002, 9003, 9004, 9005, 9006, 9007, 9008, 9018,

9022, 9043, 9044

GNC 3105

Hamlin 9022, 9023, 9024, 9025, 9026

Illico 3107

Jerrold 3103, 9002, 9003, 9004, 9005, 9006, 9007, 9008, 9018,

9022, 9043, 9044

Memorex 3106

Motorola 3103, 3110, 3111

NET 9042

Oak 9027, 9028, 9029

Pace 3107

Panasonic 9019, 9020, 9021

Paragon 3106

Philips 3104

Pioneer 3107, 9014, 9015

Pulsar 3106

Regal 9022, 9023, 9024, 9025, 9026

Rodgers 3107

Runco 3106

Scientific Atlanta 3102, 3107, 3108, 3109, 9009, 9010, 9045, 9046

Seren 3107

Sigecom 3107

Susquehanna 3107

Time Warner 3107

Tocom 9016, 9017, 9043

Toshiba 3106

ENT

CHVOL

INPUTSET

RECALLMUTING

TV CBL/SAT

ENT

CHVOL

INPUTSET

RECALLMUTING

TV CBL/SAT

Component code numbers /

Números de código de componentes

English

Digital Satellite Receiver, Cable box, TV

The following tables show brand names and their corresponding code numbers.

Español

Sintonizador de recepción vía satélite digital, adaptador para cablevisión, televisor

Las tablas que se presentan a continuación muestran las marcas y los números de código

correspondientes.

Press and hold the SET button for 2 seconds or more to set a Component Code.

Mantenga presionado el botón SET durante 2 segundos o más para ajustar un

código de componente.

Digital Satellite Receiver /

Sintonizador de recepción vía satélite digital

DirecTV Dish Network HDTV Tuner

Brand / Marca

Code No. / N.º código Code No. / N.º código Code No. / N.º código

Sony 3001, 3011, 3012 — —

DirecTV 3013, 3017, 3018, — —

3019, 3023, 3024

Dish Network — 3010, 3014, 3025 —

GE (General Electric) 3019 — —

Hitachi 3005 — —

Hughes 3004 — —

Humax — — 3402

JVC — 3010, 3014 —

Magnavox 3018 — —

Panasonic 3003 — —

Philips 3018 — —

Proscan 3002, 3007, 3019 — —

RCA 3002, 3007, 3019, 3021 — —

Samsung 3017, 3022 — 3404

Sylvania — — 3403

Toshiba 3006 — —

Usdigital — — 3401

English

3-278-786- (1)12

RM-EZ4

Operating Instructions

Manual de instrucciones

(parte posterior)

Remote

Commander

General

1 To set up the Commander.

5 Volume up: +

Volume down: –

6 To mute the volume on a

TV.

7 To turn the power of a

selected component on or

off.

8 Component Select Buttons.

Press to select a component

to operate.

Remote Button Descriptions

Operating a Component

1 Press the appropriate Component Select button on the

Commander.

TV CBL/SAT

2 Aim the Commander directly at the component.

3 Press the button for the function you want to use.

See Remote Button Descriptions for complete descriptions of“ ”

the buttons on the Commander.

Notes on Using the Remote Commander

Basically, use this Commander in the same way as the

Commanders supplied with your components.

• Using this Commander will not increase the functions of your

components. The functions of the Commander are limited to

the functions of the components themselves. For example, if

your TV does not have a MUTING function, MUTING on this

Commander will not function with your TV.

• Some functions of the component may not work with this

Commander.

• If your cable box can control volume, be sure to set its volume

to a moderate level. If the volume on the cable box is turned

down completely, you will not be able to adjust your TV’s

volume with the Commander.

This guide shows you how to set the Remote

Commander to operate your components.

Enter the code number

Example: To set up a Philips Digital Satellite Receiver

1Find the code number in

“

Component code numbers.”

If your component is not listed, try the search method described in “Searching

for the Correct Code.”

2Set the Remote Commander for code input mode.

Press and hold for more than two seconds.SET

The SET indicator lights up.

3Press the appropriate Component Select button.

CBL/SAT

4Enter the code number.

5Finish setting.

Press .ENT

Let's check

6Turn on the component you want to set up.

7Press the same Component Select button in step 3 again.

8Aim the Remote Commander at the component and press

111 on the Remote Commander.

Was the component turned off?

Yes Check that the other buttons function.

No Start over from Step 2 above, using another code number.

If you still cannot get the Remote Commander to work properly after

trying all the codes listed for your component, try the search method

described in Searching for the Correct Code.“ ”

• If the SET indicator flashes five times before lighting up, it means that the setup is incomplete.

Confirm the code number and start over from Step 4.

• If you do not input anything into the Remote Commander within 20 seconds between each step, or if you

press while setting the code number, the setup procedure will be canceled. Start over from Step 2.SET

Startup Guide

b b b

For the customers

in the U.S.A.

WARNING

This equipment has been tested and

found to comply with the limits for

a Class B digital device, pursuant to

Part 15 of the FCC Rules. These

limits are designed to provide

reasonable protection against

harmful interference in a residential

installation. This equipment

generates, uses and can radiate

radio frequency energy and, if not

installed and used in accordance

with the instructions, may cause

harmful interference to radio

communications. However, there is

no guarantee that interference will

not occur in a particular

installation. If this equipment does

cause harmful interference to radio

or television reception, which can

be determined by turning the

equipment off and on, the user is

encouraged to try to correct the

interference by one or more of the

following measures:

• Reorient or relocate the

receiving antenna.

• Increase the separation between

the equipment and receiver.

•

Connect the equipment into an

outlet on a circuit different from that

to which the receiver is connected.

• Consult the dealer or an

experienced radio/TV

technician for help.

You are cautioned that any

changes or modifications not

expressly approved in this manual

could void your authority to

operate this equipment.

Setting Up the Remote Commander

About setting up the Commander

The Commander is set up at the factory to operate Sony brand

components. However, even if you intend to use the Commander

with a Sony component, you may still need to set up the

Commander for it, depending on the component.

To set up the Commander to use with other (non-Sony)

manufacturers’ components, or to use with a component that is not

preset at the factory, you will need to follow the instructions in this

manual to preset the Commander with the correct code number for

your component. (See “Startup Guide” and “Component Code

Numbers”.)

Note

The Commander can be set up to operate only one component per button –

unless their code numbers happen to be the same. For example, you cannot set

up the Commander to operate a Sony TV and a Panasonic TV simultaneously

(because they use different code numbers).

Preset component(s)

Cable box/Digital

satellite receiver/TV

Component Select button

CBL/SAT

Factory setting

Sony TV

Sony Cable box

Troubleshooting

If you have problems setting up or using the Commander:

•

When setting up the Commander, carefully go through the procedures

described in Startup Guide.“ ” If the code that is listed first for your component

does not work, try

other

codes for

that

component – in the order in which they

are listed. If all the codes fail to work (or if your component is not listed in this

manual), try using the procedures in “ ”Searching for the Correct Code.

• Make sure that you are aiming the Commander directly at the component,

and that there are no obstructions between the Commander and the

component.

• Make sure the batteries you are using are not worn out, and that they are

inserted correctly.

• Check that the appropriate TV or CBL/SAT button is pressed.

• Check that the component has infrared remote capability. For example, if

your component did not come with a remote control, it probably is not

capable of being controlled by the Remote Commander.

• Should any problem persist, reset the Commander to the factory setting by

pressing the 1, INPUT and VOL – buttons simultaneously.

For the customers in the U.S.A.

Customer Support Information

After you have read through this manual, if you still cannot get the Remote

Commander to work properly, call the Sony Customer Support Helpline at

1-800-822-2217.

Code No. / N.º código

c c

ENT

SET

TV CBL/SAT

2 To change the input mode.

3 4 9, and

To change the channel.

q; CH +: Channel up.

CH –: Channel down.

qa To operate the JUMP FLASHBACK, or CHANNEL RETURN function on

the TV.

ENT

Produkt Specifikationer

Mærke:	Sony
Kategori:	Fjernbetjening
Model:	RM-EZ4

Har du brug for hjælp?

Hvis du har brug for hjælp til Sony RM-EZ4 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Fjernbetjening Sony Manualer

16 September 2024

15 September 2024

14 September 2024

9 September 2024

2 September 2024

2 September 2024

2 September 2024

2 September 2024

2 September 2024

Sony RM-VS10TV Manual

2 September 2024

Fjernbetjening Manualer

Nyeste Fjernbetjening Manualer

Morel MPS-R1 Manual

18 November 2024

One For All URC 2110 Manual

16 November 2024

One For All KE4910 Manual

16 November 2024

Interphone Handlebar Control Manual

2 November 2024

Canon BG-E20 Manual

12 Oktober 2024

Logitech Harmony 785 Manual

8 Oktober 2024

DSC WS4949 Manual

8 Oktober 2024

Neewer RT112 Manual

7 Oktober 2024

Neewer RT113 Manual

7 Oktober 2024

MB Quart N1-RC Wireless Manual

6 Oktober 2024