Sony RM-VS10TV Manual

Sony Fjernbetjening RM-VS10TV

Læs nedenfor 📖 manual på dansk for Sony RM-VS10TV (4 sider) i kategorien Fjernbetjening. Denne guide var nyttig for 17 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/4

English

For the customers in the U.S.A.

WARNING

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

You are cautioned that any changes or modifications not expressly

approved in this manual could void your authority to operate this

equipment.

NBefore you begin

Features

• This is a remote control unit with built-in speaker to enhance your

enjoyment of television sound. It is convenient to use if it is

difficult to hear the television sound when there is other

surrounding noise or human voices present.

• The television sound can be easily heard through the high-fidelity,

compact speaker.

Clearer, fuller sound can also be heard when listening to the

television sound.

• The volume control for the speaker enables you to listen to the

sound at the most appropriate volume.

• Because the speaker system uses infrared-ray communication, it

provides great portability, allowing you to carry it around the

room. The sound can be enjoyed anywhere within the range the

infrared rays can reach, such as on top of a table or next to a sofa.

• A microphone is included, which can pick up sound directly from

the television speakers.

Transmitter installation can be performed easily, without

troublesome cord connections. The transmitter also operates with

a television not equipped with an audio output terminal.

• The unit is also equipped with a three-hour timer OFF function.

Even if you forget to turn off the power of the speakers, the power

turns off automatically after three hours to prevent excessive

power consumption.

About Presetting the Commander

The Commander is preset at the factory to operate Sony brand TVs.

If you’re using the Commander with a Sony brand TV, you won’t

need to preset the Commander before you start using it.

To set up the Commander to use with other (no:-Sony)

manufacturers’ TV, or to use with an analog cable box, you’ll need to

follow the instructions in this manual to preset the Commander with

the correct code number for your components.

Notes

• The Commander can be set up to operate only one component per

button – unless their code numbers happen to be the same. For

example, you cannot set up the Commander to operate a Sony TV and a

Panasonic TV simultaneously (because they use different code

numbers).

• You may not be able to operate even a Sony brand TV with the factory

setting. In such a case, follow the procedure in “Setting the code”.

Usage example

Living room

When watching the television with others, you can enjoy the sound

at a volume of your own choice.

Bedside

Late-night programs can be enjoyed without disturbing people in

other rooms.

Kitchen

While away from the television, you can hear the clear sound near at

hand.

Sound coverage range

The illustration below shows the approximate area covered by the

infrared rays emitted from the transmitter.

Notes

• This system utilizes infrared rays for communication, so noise (hissing)

from the speaker can increase as the Commander goes farther away

from the transmitter, even within the range illustrated above. The sound

will also be cut off and noise will be generated if the infrared rays are

blocked. These are characteristics of infrared-ray communication and do

not indicate an equipment malfunciton.

• Do not place your hand in front of the infrared receptor.

• Place the Commander so the infrared receptor of the Commander faces

the transmitter. If the Commander is used in a position within the

range illustrated above, the sound can be heard from the speaker of the

Commander.

• The sound you hear varies according to the position of the Commander

and the transmitter. Try finding a position that yields the best sound.

• Even if there are irregularities in the clarity of the infrared emitter of the

transmitter, this will not influence the range and other functions of the

infrared rays.

Precaution

On operation

Never drop the Commander and transmitter or subject them to

strong shock. This may damage the equipment.

NPreparations

Preparing the power source of the

Commander

Installing the batteries

Slide open the battery compartment and insert four size AA (R6)

batteries (not supplied).

Be sure to line up the and on the batteries with the e E e and E on

the battery compartment.

1 2

When to replace the batteries

Under normal conditions, batteries will last for up to approximately

60 hours of use (when using Sony LR6 alkaline batteries, for 5 mW

speaker output usage). If the Commander does not operate properly

or the speaker power lamp is dim or off, the batteries might be worn

out. Replace the batteries with new ones.

Notes

• Replace all batteries with new ones.

• Do not take more than 20 minutes to replace the batteries; otherwise,

your setting of the code number will be erased.

• The battery life may vary depending on the frequency of use.

Notes on batteries

• Do not mix old batteries with new ones or mix different types of

batteries together.

• If the electrolyte inside the battery should leak, wipe the

contaminated area of the battery compartment with a cloth, and

replace the old batteries with new ones. To prevent the electrolyte

from leaking, remove the batteries when you plan not to use the

Commander for a long period of time.

Using on house current

Notes

• If the AC adaptor is removed for more than 20 minutes when

batteries are not inserted, your setting of the code number will be

erased. It is recommended to use the Commander with the

batteries inserted, even when using the Commander with the AC

power adaptor.

• Use only the AC power adaptor AC-E45HG (not supplied). Do not

use any other AC power adaptor.

Setting the code

Setting by entering the code number

1See the tables in “Component code numbers,” and find the three-

digit code number for the desired component.

If more than one code number is listed, use the number that’s

listed first to complete the steps below.

For example, if you’re setting up a Philips TV, you would use the

code number 056.

If your component is not listed, see “Setting by searching for the

correct code.”

2Press the POWER button while holding

the SLEEP button pressed.

3Press the button for the component that

you want to set up (TV or CABLE).

4Enter the component’s code number.

For example, if you’re entering the code

for a Philips TV, you would press

5Press the ENT button.

6Aim the Commander to your component and check if you can

operate it using the Commander.

If you press a wrong button in step 4

Press the button while holding the POWER SLEEP button pressed

and then return to step 3.

If you cannot operate your component

• First try repeating these setup procedures using another code listed

for your component (see the tables in “Component code

numbers”).

• If after trying all the codes listed for your component you still

cannot get the Commander to work properly, try the search

method described in “Setting by searching for the correct code.”

Tip

You can write down the code number on the label inside the battery

compartment lid and this Operating Instructions manual.

1Press before operating the analog cable box.

2To change the channel. For example, to change to channel 5,

press ).0 and 5 (or, press 5 and ENT

3To turn on and off the power.

4Channel up: +

Channel down: –

Notes

• There may be cases in which you may turn on/off the analog cable box

by pressing the CHANNEL + or CHANNEL – buttons on the Commander.

• If your analog cable box can control volume, be sure to set its volume

control to a medium position. If the volume on the analog cable box is

turned down completely, you will not be able to adjust your TV’s

volume with the Commander.

1Press before operating the TV.

2To operate SLEEP function on the TV. (Works only for a TV with

the SLEEP function.)

3TV volume up: +

TV volume down: –

4To change the input mode.

5To turn on and off the power.

6To change the channel. For example, to change to channel 5,

press ).0 and 5 (or, press 5 and ENT

7Channel up: +

Channel down: –

Operating an analog cable box

3-220-956-11 (2)

Speaker Remote

Commander system

RM-VS10TV

Operating Instructions

Manual de instrucciones (parte posterior)

Transmitter

Approx. 3 m

(118 1/8 in.)

Approx. 3 m

(118 1/8 in.)

Infrared ray

Remote

Commander

Approx. 7 m (23 ft.)

to an AC outlet

Setting up the transmitter

1 Connect the transmitter to a TV.

AUsing the supplied connecting cord

• To connect to the LINE OUT jack

• To connect to a headphones jack

(The sound does not come out of the television speakers.)

Notes

• When the transmitter is connected to a headphones jack, use the

volume control on this Commander to adjust the volume, while

keeping the volume of the TV at an appropriate level.

• Sound from the microphone will be shut off automatically if a

connection cord is connected to the television LINE OUT jack or

headphones jack of a TV.

• The sound sent from the transmitter is monaural. If the input

signal is stereo, it is converted to a monaural signal inside the

transmitter.

BUsing the supplied microphone

1Remove the microphone from

the underside of the transmitter.

2Tear off the coated paper from

the adhesive surface of the

microphone.

3Attach the microphone to the television speaker.

Adjust the volume of the TV.

Notes

• Wipe off dirt, dust, or moisture on the attached surface of the

speaker with a dry cloth before attaching the microphone to it. The

adhesion of the adhesive label on the microphone recovers if

wiped with a moist cloth.

• Use the LINE OUT jack or the headphones jack of the television if

the speaker surface is made of cloth or other material that can be

easily stripped off.

• Attach the microphone in a position where the sound can be heard

best if the television speaker grill is large or long.

• When the microphone is attached to a stereo television, you can

use either speaker grill, left or right. It makes no difference in the

sound from the speaker of the Commander.

2 Connect the transmitter to a power source.

Note

Use only the supplied AC power adaptor. Do not use any other AC

power adaptor.

Transmitter

to the AUDIO IN B jack

Connecting cord

(supplied)

Left channel

(white)

Right channel

(red)

to the LINE OUT jack

Transmitter

to the AUDIO IN A jack

Connecting cord

(supplied)

to a headphones jack

(stereo minijack)

Left channel

(white)

Right channel

(red)

to a headphones jack

(stereo phone jack)

Unimatch plug

adaptor

(not supplied)

Microphone

(In the middle of the television speaker grill)

NOperations

Operating a component

1Turn on the transmitter. The infrared emitters light up.

2Turn on the power of the speaker.

3Press the button of the desired component on the Commander (TV

or CABLE).

4Point the Commander directly at the component.

5Press the button for the function you want to use.

See “Remote button descriptions” for a complete description of

the buttons on the Commander.

6Adjust the volume of the speaker of the Commander.

Notes on using the Commander

Basically, use this Commander in the same way as the remote control

supplied with your TV or analog cable box.

• Using this Commander will not add additional functions to your

TV or analog cable box. The functions of the Commander are

limited to the functions of the equipment itself. For example, if

your TV does not have a SLEEP function, the button on thisSLEEP

Commander will not function with your TV.

• Some functions of your TV or analog cable box may not work with

this Commander.

• If your analog cable box can control volume, be sure to set its

volume switch to a medium position. If the volume on the analog

cable box is turned down completely, you will not be able to adjust

your TV’s volume with the Commander.

Notes on adjusting the volume

When connecting to the LINE OUT jack

• Use the VOL control on the Commander to adjust the speaker

volume.

• If noise increases when the Commander goes outside the range

where the infrared rays reach or when the infrared rays are

obstructed, the mute function operates automatically, and the

sound from the speaker cannot be heard. The mute function is

canceled automatically when the Commander moves closer to the

transmitter or there is no obstruction to the infrared rays.

When using the microphone or connecting to the headphone jack

If you cannot get the desired speaker volume even if you increase the

speaker volume to the maximum using the VOL control of the

Commander, turn up the volume on the television.

Listening to through an earphone (not supplied)

Connect an earphone (not supplied) to the EARPHONE jack on the

Commander.

You can store your earphone in the battery compartment on the

bottom of the Commander when not in use.

When the Commander is not in use

First turn off the SPEAKER POWER switch on the Commander and

then turn off the POWER switch of the transmitter. Noise may be

heard if the power of the transmitter is turned off first.

Note

The power of the speaker turns off automatically after three hours to

prevent exessive power consumption.

Press the SPEAKER POWER switch again if the power is turned off

while you are watching TV. (The remote control functions can be

used even if the power of the speaker is turned off.)

Transmitter

AC power adaptor

(not supplied)

to DC IN 4.5V jack

AC power

adaptor

(supplied)

to DC IN 9V jack

to an AC outlet

POWER ON/ OFF

Remote button descriptions

Operating a TV

NAdditional information

Troubleshooting

Sound problems

No sound/Muffled sound

• Check that the SPEAKER POWER lamp of the Commander is on.

• Check that the transmitter is turned on.

• Check if the speaker volume control is set to “0” (minimum).

• Check that all connections are correct.

• Turn up the volume on the television.

Distortion

• Check if the volume on the television is turned up too high.

• Check if the SPEAKER POWER lamp is dim or off.

tReplace the batteries of the Commander.

Loud background static

• Check that the distance between the Commander and the

transmitter is within the signal connection range. Noise from the

speaker increases as the Commander goes farther away from the

transmitter. This is due to characteristics of the infrared-ray

communication and does not indicate a malfunction of the unit.

• Check that there is no obstruction between the Commander and

the transmitter.

• Make sure that the Commander and component are not exposed to

direct sunlight.

• Change the position or angle of the transmitter.

• Check if the SPEAKER POWER lamp is dim or off.

tReplace the batteries of the Commander.

• If there is another transmitter in operation, turn off the power of

the other transmitter or move it to a location where the infrared

rays do not interfere.

Problems when setting up or using the Commander

To set up the Commander, carefully go through the procedure

described in “Setting the code”. If more than one code is listed for

your component and the first one fails, try the next one, and so forth.

If none of the codes work (or if your component is not listed), go to

the steps in “Setting by searching for the correct code.”

You cannot set the code

• Make sure that the batteries are not worn out, and that they are

inserted correctly.

You cannot operate the TV or analog cable box with the Commander

in spite of successful setting

• Check that you are aiming the Commander directly at the

component, and that the Commander is within the remote control

operation distance.

• Check that there are no obstructions between the Commander and

the component.

• Make sure that the batteries are not worn out.

• Check that the TV or CABLE button is pressed to choose your

desired component.

• Check that the component has infrared remote capability. For

example, if your component did not come with a remote

commander, it probably is not capable of being controlled by a

remote commander.

• Check if your setting of the codes has been changed owing to

mishandling or some other cause.

• Check if your setting of the codes has been erased owing to leaving

the batteries (or AC power adaptor) removed for more than 20

minutes.

tInsert new batteries and repeat the set up procedure.

Noise comes out from the speaker when you press a button

• Check that the distance between the Commander and the

transmitter is within the signal connection range.

Should any problem persist, reset the Commander to the factory

setting by pressing POWER, INPUT and VOL – buttons

simultaneously.

For the customers in the U.S.A.

Customer Support Information

If – after you’ve read through this manual – you still cannot get the

Remote Commander to work properly, call the Sony Customer

Support Helpline at 1-800-822-2217.

Specifications

General

Modulation system Frequency modulation

Carrier frequency 2.3 MHz (monaural)

Transmitter TMR-IF10M

Power source DC IN 9 V jack accepts power supplied from the

AC power adaptor for use on 120 V AC, 60 Hz

voltage.

Input Internal microphone or phone jack/stereo mini

jack

Signal connection range Maximum: 7 m* (23 ft.) (when the Commander

is facing directly toward the transmitter)

Dimensions 130 × 38 × 70 mm (5 1/ 8× 1 1/ 2× 2 7/8 in.)

(w × h × d)

Mass Approx. 100 g (4 oz.)

Remote Commander RM-VS10

Power source Four size AA (R6) batteries (not supplied)/

external DC 4.5 V power sources (AC power

adaptor not supplied)

Maximum speaker output

0.8 W

Battery life (for 5 mW speaker output usage)

Approx. 20 hours (using Sony battery R6)

Approx. 60 hours (using Sony alkaline battery

LR6)

Remote control operation distance

Approx. 7 m (23 ft.) (when facing directly*

toward the infrared receptor of your TV/analog

cable box)

Dimensions 93 × 86 × 158 mm (3 3/ 4× 3 1/ 2× 6 1/4 in.)

(w × h × d)

Mass Approx. 355 g (13 oz.) (including batteries)

Supplied accessories

AC power adaptor (for the transmitter) (1)

Connecting cords (stereo mini plug pin plug 2) (1)× 1 y×

Optional accessories

Plug adaptor PC-234HG (stereo mini jack stereo phone plug)y

Connecting cords RK-C310 (pin plug × 2 y pin plug × 2)

RK-C315 (pin plug × 2 y pin plug × 2)

RK-C320 (pin plug × 2 y pin plug × 2)

Connecting cords RK-G129 (stereo mini plug 1 pin plug 2)×y×

Earphone ME-L82

AC power adaptor (for the Remote Commander) AC-E45HG

*The distance may vary depending on using conditions and the

manufacturer and equipment that is used.

Design and specifications are subject to change without notice.

Component No.

Analog cable box

It will be useful to write down the code numbers of your components in

the chart above, so that you can refer to them when registering the code

numbers with the Commander.

POWERSLEEP

CABLE

ENT

INPUT

ENT

SLEEP

SPEAKER POWER

VOL

CABLE TV POWER

VOLU ME CH AN NE L

SPEAKER POWER

TVCABLE

INPUT

ENT

SLEEP

SPEAKER POWER

VOL

CABLE TV POWER

VOLUME CHANNEL

INPUT

ENT

SLEEP

SPEAKER POWER

VOL

CABLE TV POWER

VOLUME CHANNEL

Transmitter

Setting by searching for the correct code

If you have tried all the code numbers listed for your component and

you still cannot get the Commander to work (or if your component is

not listed in the “Component code numbers” tables), try these steps.

1Power on the component you want to set up.

2Press the POWER SLEEP button while holding the button pressed.

3Press the button for the component on the Commander that you

want to set up (TV or CABLE).

4Press and release the button. Then press and releaseCHANNEL +

the button.POWER

5Repeat step 4 until the correct code number is found.

Each time you press the button and then the CHANNEL + POWER

button, a new code number will be transmitted.

Keep trying until your component operates by receiving the

transmitted signal from the Commander (e.g., the power turns off,

the CHANNEL + function works, etc.). Be patient as you do this; it

may take 60 or 70 tries until the correct code number is located.

6When the correct code is found, press the button.ENT

7Check that the Commander is operating the other functions of

your component by pressing the corresponding buttons on the

Commander. If they seem to be working properly, you’re done

setting up the Commander.

If the component does not operate properly, repeat steps 1 to 6 and

search for another code.

If you still cannot get the Commander to work properly, see

“Troubleshooting.”

Component code numbers

TV codes

Brand Code No.

Sony 001

Admiral 002, 014, 009

AOC 012

Audinac 034

Bell&Howell 014, 009, 038

Brocsonic 003, 012

Craig 022, 023, 020, 021

Croslex 011

Crown 023

Curtis Mathis 003, 019, 023

Daewoo 035, 036, 003, 041

Daytron 013

Emerson 022, 013, 020, 021, 023, 003, 015, 042

Fisher 025

General Electric 045, 002, 018, 003, 007, 027

Gold Star/LG 003, 013, 012, 030, 046, 050, 051, 049

Hitachi 031, 013, 003, 032

JC Penny 003, 002, 030, 007

JVC 028, 029

KTV 033, 013, 003, 023, 034

LXI (Sears) 002, 003, 011, 025, 019, 012, 052

Magnavox 011, 012, 013, 003, 043, 047, 018

Mitsubishi/MGA 066, 024, 003, 012

NEC 003, 012

Panasonic 018, 016, 017, 007, 049, 067

Philco 068, 035, 031, 011, 013, 003

Philips 056, 043, 011

Pioneer 037, 018, 019

Portland 003, 008

Quasar 018, 007, 048

Radio Shack 002, 012, 024, 023

RCA/Proscan 053, 002, 003, 004, 005, 006, 007, 008,

044, 045, 046, 018

Samsung 055, 026, 012, 013, 003, 023, 027

Sanyo 023, 025, 054, 069

Scott 023, 012

Sharp 014, 013, 015, 070

Signature 2000 014, 009

Sylvania 011, 012, 003

Symphonic 023, 039, 040

Toshiba 060, 019, 014, 052, 059

Videch 031, 003, 012

Wards 013, 003, 015, 012

Zenith 009, 010

Analog cable box codes

Brand Code No.

Hamlin/Regal 022, 023, 024, 025, 026

Jerrold/G.I 043, 001, 002, 003, 004, 005, 006, 007,

008, 018, 022

Oak 027, 028, 029

Panasonic 019, 020, 021

Pioneer 014, 015

Scientific Atlanta 009, 010, 011

Tocom 043, 016, 017

Zenith 012, 013

Polarity of the plug

INPUT

ENT

SLEEP

SPEAKER POWER

VOL

CABLE TV POWER

VOLU ME CH AN NE L

VOL

EARPHONE jack

Component that can be

preset

Analog cable box

Button

CABLE

Factory setting

Sony TV

–

Produkt Specifikationer

Mærke:	Sony
Kategori:	Fjernbetjening
Model:	RM-VS10TV

Har du brug for hjælp?

Hvis du har brug for hjælp til Sony RM-VS10TV stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Fjernbetjening Sony Manualer

16 September 2024

15 September 2024

14 September 2024

9 September 2024

2 September 2024

2 September 2024

2 September 2024

2 September 2024

2 September 2024

Sony RM-VS10TV Manual

2 September 2024

Fjernbetjening Manualer

Nyeste Fjernbetjening Manualer

Nanlite BT-BCS-48V3.5mm Manual

21 December 2024

SMK-Link VP3700 Manual

17 December 2024

Metronic ZAP 2 Unic - 495399 Manual

17 December 2024

Metronic ZAP 3 - 495373 Manual

17 December 2024

Metronic ZAP 3 - 495309 Manual

17 December 2024

Metronic ZAP 3 - 495308 Manual

17 December 2024

Metronic 495390 Manual

17 December 2024

Metronic 495387 ZAP 3 Manual

17 December 2024

Metronic ZAP 6 Manual

17 December 2024

EQ-3 HM-RC-19-B Manual

16 December 2024