Sony RM-V302 Manual

Sony Fjernbetjening RM-V302

Læs nedenfor 📖 manual på dansk for Sony RM-V302 (2 sider) i kategorien Fjernbetjening. Denne guide var nyttig for 33 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

Installing the Batteries

Before replacing the batteries, have new ones ready beforehand.

Slide open the battery compartment and insert two size AA (R6)

batteries (not supplied).

Be sure to line up the + and – on the batteries with the + and – on the

battery compartment.

1 2

When to replace the batteries

Under normal conditions, batteries will last up to six months. If the

Commander does not operate properly, the batteries might be worn

out. Replace the batteries with new ones.

Notes

• Replace both batteries with new ones.

• Do not take more than 3 minutes to replace the batteries; otherwise,

your setting of the code numbers will be erased.

Notes on Batteries

• Do not mix old batteries with new ones or mix different types of

batteries together.

• If the electrolyte inside the battery should leak, wipe the

contaminated area of the battery compartment with a cloth and

replace the old batteries with new ones. To prevent the electrolyte

from leaking, remove the batteries when you plan not to use the

Commander for a long period of time.

Setting the Code

Follow the steps 1 and 2 below for each component you plan to use

with the Commander.

Step 1: Entering the Code Number

1See the supplied “Component Code numbers”, and find the three-

digit code number for the desired component.

If more than one code number is listed, use the number that’s

listed first to complete the steps below.

For example, if you’re setting up a Philips’ VCR, you would use

the code number 035.

If your component isn’t listed, see “Searching for the Correct

Code.”

2While pressing the SET button, press the

POWER button.

3Press the button of the component that

you want to set up.

Note

On the , and buttons, “cable box”, “receiver”,CBL/SAT RCVR, DVD

and “DVD player” are assigned respectively at the factory. But you

can also assign other components on these buttons. For details, see

“Changing the Component Type on the , and CBL/SAT RCVR, DVD

buttons.”

Changing the Factory Setting for the

Volume Control

1While pressing the SET POWER button, press the button.

2Press the RCVR button.

3Press the VOL+ button.

4Press the ENT button.

The volume control setting is changed to “receiver/amplifier.” You

can control the volume of the receiver (or amplifier) of the RCVR

button while selecting any component.

Notes

• If you are using more than one receiver (or amplifier) and have set

it on the button, when selecting these buttons youCBL/SAT DVD or

cannot control the volume of the receiver (or amplifier) of the RCVR

button.

• If you change the setting of the button to a component otherRCVR

than a receiver or amplifier, the volume control setting of video

components will return to “TV” even if you have changed the

factory preset volume control. In this case, you will not be able to

control the volume from audio components other than a receiver

or amplifier.

To reset to factory preset volume control

In step 3 above, press VOL– instead.

Operating a Component

1Press the button of the desired

component on the Commander.

2Point the Commander directly at the

component.

3Press the button for the function you want to use.

See “Remote Button Descriptions” for complete descriptions of the

buttons on the Commander.

Notes on Using the Remote Commander

Basically, use this Commander in the same way as the Commanders

supplied with your components.

• Using this Commander will not increase the functions of your

components. The functions of the Commander are limited to the

functions of the components themselves. For example, if your TV

does not have a MUTING function, the button on thisMUTING

Commander will not function with your TV.

• Some functions of the component may not work with this

Commander.

• If your cable box can control volume, be sure to set its volume

switch to a medium position. If the volume on the cable box is

turned down completely, you will not be able to adjust your TV’s

volume with the Commander.

Setting a channel with a single button

(Channel Macro function)

You can program the Channel Macro function on any of the buttons

listed below (macro keys).

For example, instead of pressing , , and then ENT button to

change the TV channel, you can perform these operations by

pressing only the N

button.

The macro keys are:

N m M x X z, , , , , and REC.

(During TV, analog cable box, or digital satellite receiver operations

only.)

The series of operations that can be programmed must be consisted

of two to four sequential pressings of to buttons or ENT button.

Note

The Channel Macro function may not work correctly for some

components.

For the customers in the U.S.A.

WARNING

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

You are cautioned that any changes or modifications not expressly

approved in this manual could void your authority to operate this

equipment.

Setting Up the Remote Commander

About Presetting the Commander

The Commander is preset at the factory to operate Sony brand

components.

If you’re using the Commander with a Sony component, you won’t

need to preset the Commander before you start using it.

To set up the Commander to use with other (non-Sony)

manufacturers’ components, or to use with a component that is not

preset at the factory, you’ll need to follow the instructions in this

manual to preset the Commander with the correct code number for

your components. (See the supplied “Component Code Numbers”

also.)

Notes

• The Commander can be set up to operate only one component per

button – unless their code numbers happen to be the same. For

example, you cannot set up the Commander to operate a Sony TV

and a Panasonic TV simultaneously (because they use different

code numbers).

• You may not be able to operate even a Sony brand component with

the factory presetting. In such a case, follow the procedure in

“Setting the Code.”

Remote Button Descriptions

4Enter the component’s code number.

For example, if you’re entering the code

for a Philips VCR, you would press .

5Press and release the ENT button to store

the code number in the Commander’s

memory.

6Go to “Step 2: Checking if the Code Number Works” to finish

setting up.

If you press a wrong button in step 4

Press the POWER button while pressing the button and then goSET

back to step 3.

Step 2: Checking if the Code Number Works

1Power on the component you want to set up.

2Aim the Remote Commander at the component and press a button

to check if that button works.

For example, press the button to see if it works on yourPOWER

component .

3Check that the other buttons of the Commander is operating the

corresponding functions of the component.

You can write down the code number on the label inside the

battery compartment lid.

If the Commander Doesn’t Seem to Be Working...

• First, try repeating these setup procedures using the other codes

listed for your component (see the supplied “Component Code

Numbers”).

• If – after trying all the codes listed for your component – you still

cannot get the Commander to work properly, try the search

method described in “Searching for the Correct Code.”

Searching for the Correct Code

If you’ve tried all the code numbers listed for your component and

you still cannot get the Commander to work (or if your component is

not listed in the “Component Code Numbers” tables), try these

steps.

1Power on the component you want to set up. Insert a tape or disc

if necessary.

2While pressing the SET POWER button, press the button.

3Press the button of the component on the Commander that you

want to set up.

4Press and release the CH+ button. Then press and release the

POWER button.

5Repeat step 4 until the correct code number is found.

Each time you press the button and then the CH+ POWER button,

a new code number will be transmitted.

Keep trying until your component operates by receiving the

transmitted signal from the Commander (e.g., the power turns off,

the CH+ function works, playback starts, etc.) Be patient as you do

this; it may take about 100 tries until the correct code number is

located.

6When the correct code is found, press the button to store theENT

code number in the Commander’s memory.

7Check that the Commander is operating the other functions of

your component by pressing the corresponding buttons on the

Commander. If they seem to be working properly, you’re done

setting up the Commander.

If the component does not operate properly, repeat steps 1 to 6 and

search for another code.

If you still cannot get the Commander to work properly, see

“Troubleshooting.”

Changing the Component Type on the CBL/

SAT, RCVR, and DVD buttons

At the factory, “cable box” is assigned on the CBL/SAT button,

“receiver” on the button, and “DVD player” on the RCVR DVD

button. By completing the following procedure, you can change this

setting so that you can set up any component on these buttons.

1While pressing the SET POWER button, press the button.

2Press the CBL/SAT RCVR DVD, , or button.

3Press and release the x (stop) button.

4Press and release one of the following buttons;

to assign a VCR

to assign a digital satellite receiver, a digital cable box or a

digital video recorder

to assign a receiver

to assign a CD player

to assign a tape deck

to assign an MD deck or a DAT deck

to assign a TV

to assign an analog cable box

to assign a DVD player

5Press and release the ENT button.

6Enter the component’s code number by following steps 2 to 6 of

“Entering the Code Number”, or steps 1 to 7 of “Searching for the

Correct Code.”

Controlling the Volume of Video

Components Connected to an Audio

System

The Commander is factory preset based on the assumption that you

hear the sound of your video components from your TV’s speakers,

and that you hear the sound of your audio components from the

loudspeakers connected to your receiver (or amplifier).

Factory Setting:

*If you assign an audio component on the CBL/SAT DVD or button, you can

control the volume of the receiver (or amplifier) on the button. If youRCVR

assign video components on these buttons, you can control the volume of the

TV.

Thus you can control the volume of your TV or receiver (or

amplifier) while operating a video or audio component without first

having to press the button. For example, to control theTV RCVR or

volume for your VCR channels, you don’t need to press the TV

button first.

However, if your video components are connected to an audio

system, you probably hear your TV’s or VCR’s sound from the

loudspeakers connected to your receiver (or amplifier), not from

your TV speakers. In this case, you need to change the factory setting

so that you can control the volume of your video components

without first having to switch to the receiver (or amplifier).

To change the factory setting for the volume control, follow the

procedures below.

Note

This feature is effective only when a receiver or amplifier is set up on

the RCVR button. You cannot control the volume of a receiver (or

amplifier) set up on button while operating aCBL/SAT DVD or

component of another button.

Button

VCR, CBL/SAT , DVD* *

RCVR

Controls the volume of

Receiver (or amplifier)

Component that can be preset

VCR

Analog cable box/Digital cable box/

Digital satellite receiver/Receiver/

CD player/Tape deck/

MD deck/DAT deck/DVD/TV/

VCR/Digital video recorder

Button

VCR

CBL/SAT

RCVR

DVD

Factory setting

Sony TV

Sony VHS VCR

—

Sony receiver

Sony DVD player

Operating a tape deck

English

3-252-841- (1)11

Remote Commander RM-V302

Operating Instructions

Manual de instrucciones (parte posterior)

General

1To set up the Commander,

press SET while pressing

POWER.

2Component select buttons. To

switch to the operations of each

component, press the button on

which that component is

assigned.

5*1Volume up: +

Volume down: –

7*1To mute the volume on TV or

receiver (amplifier).

qa To turn on and off the power of

the selected component.

*1These buttons control the volume of

either TV or receiver (amplifier). See

“Controlling the Volume of Video

Components Connected to an

Audio System” for details.

3 q; ql, , and

Tape operation buttons.

For dual cassette decks,

operation buttons for Deck A

(for Sony-brand dual cassette

deck, buttons for Deck B).

PIP: To reverse.

N: To play.

m: To rewind.

M: To fast-forward.

zREC: To record, press N

while pressing zREC.

First release , thenN

release REC.z

x: To stop.

X: To pause.

8 9 qd qk, , , and

Operation buttons for Deck B

(for Sony-brand dual cassette

deck, buttons for Deck A).

Specifications

Operable distance Approx. 7 m (23 ft) (varies depending of the

component of each manufacturer)

Power requirements Two size AA (R6) batteries (not supplied)

Battery life Approx. 6 months (varies depending on frequency of

use)

Dimensions Approx. 55 × 200 × 32 mm (w/h/d)

(2 1/ 4× 7 7/ 8× 1 5/16 in.)

Mass Approx. 95 g (3.4 oz.) (not including batteries)

Design and specifications are subject to change without notice.

The CE mark on the unit is valid only for products

marketed in the European Union.

SET

POWER

DVD RCVR

VCR CBL / SAT

4 5 6

7 8

PIP ENT

POWER

CHVOL

TV / VIDEO

DVD

TVMD

CDTUNER T APE

VIDEO 2

PHONE

DVD RCVR

VCR CBL / SA T

SET

DISPLAY

SLEEP

MUTING RECALL

GUIDEMENU

REC

VIDEO 1 AUX

2 3

Operating an analog cable box

qs and qd

To change the channel. For

example, to change to channel

5, press and (or press 0 5 5 and

ENT).

qf Channel up: +

Channel down: –

Notes

• There may be cases you may turn on/off the cable box by pressing the CH+ or

CH– buttons on the Commander.

• If your cable box can control volume, be sure to set its volume control to a

medium position. If the volume on the cable box is turned down completely,

you will not be able to adjust your TV’s volume with the Commander.

ENT: To reverse.

: To play.

: To rewind.

: To fast-forward.

: To stop.

MENU: To record, press

while pressing MENU.

First release , and

then release MENU.

OK: To pause.

qh To select Deck A or Deck B

(dual cassette deck only).

If your tape deck’s commander has

one set of tape operating buttons, and

has an A/B button for the deck

selection, use the RECALL button to

select Deck A or Deck B.

To program a series of operations

1Press the desired component select button.

(You can select “TV”, “ analog cable box”, or “digital satellite

receiver” only.)

2While pressing the desired macro key, press the buttons required

for the operations in sequence.

For example, to program t t ENT on the N button, hold

down , N first, press , and ENT in sequence, and then release

Notes

• Even if you try to program more than four operations and press the

corresponding buttons in step 2 above, only the first four buttons

that were pressed will be programmed.

• If you try to program only one operation on a macro key, the

setting operation will be rejected.

• You can program the Channel Macro function for up to three

components only. To program for the fourth component, first clear

all macro keys for a component.

To change or clear the program

When you want to change the setting or if you are no longer using

that programmed operation, follow the procedure below to

overwrite or clear the program.

1Hold down the macro key that you want to change or clear.

2After waiting for about three seconds, press the new sequence of

buttons, or, to clear the program, press and release , and then

press and release ENT.

3Release the macro key.

Note

Be sure to wait for about three seconds in step 2 above. While you

are holding down the macro key and waiting, the programmed

signals are transmitted; therefore, if you are aiming the Commander

at your component, the programmed operations may be performed

before you go on with the procedure.

Troubleshooting

If you have problems setting up or using the Commander:

• When setting up the Commander, carefully go through the procedures

described in “Setting the Code.” If the code that’s listed first for your

component doesn’t work, try all the codes for your component - in the order

in which they’re listed. If all the codes fail to work (or if your component is

not listed in this manual), try using the procedures in “Searching for the

Correct Code.”

• Check that you’re aiming the Commander directly at the component, and that

there are no obstructions between the Commander and the component.

• Make sure the batteries you’re using are not worn out, and that they’re

inserted correctly.

• , , , Check that the button of the TV VCR CBL/SAT RCVR, or DVD is pressed to

choose your desired component.

• Check that the component has infrared remote capability. For example, if

your component didn’t come with a remote commander, it probably isn’t

capable of being controlled by a remote commander.

• If your video components are connected to an audio system, make sure

you’ve set up the Commander as described in “Controlling the Volume of

Video Components Connected to an Audio System.”

• Should any problem persist, reset the Commander to the factory setting by

pressing the buttons simultaneously.POWER TV VIDEO, / and VOL–

For the customers in the U.S.A.

Customer Support Information

If – after you’ve read through this manual – you still cannot get the

Remote Commander to work properly, call the Sony Customer

Support Helpline at 1-800-822-2217.

Operating a TV

3To operate the Picture-in-

Picture function. Press each

button or combination of

buttons as described in the

table below.

4To change the input mode.

6To display the current channel

on TV.

8To move the cursor upward,

downward, to the left, or to the

right.

9To call up the MENU display.

qs and qd

To change the channel. For

example, to change to channel

5, press and (or press and0 5 5

ENT).

PIP operations

Press To

PIP Turn on/off the “window” picture.

GUIDE Turn off the “window” picture.

m M or Change the TV channel in the “window” picture.

zREC Change the input mode of the “window” picture.

xMove the location of the “window” picture.

NSwap the “main” picture and the “window” picture.

XFreeze the “window” picture.

Note

If you have programmed the Channel Macro function for TV operation, the

button used as a macro key cannot be used for PIP operation.

qf CH+: Channel up.

CH–: Channel down.

qg To operate SLEEP function on

the TV. (Works only for a TV

with the SLEEP function.)

qh To operate JUMP FLASHBACK,

or CHANNEL RETURN function

on the TV depending on the

setting of the TV’s

manufacturer.

qk To enter the selection.

Operating a VCR

q; ql, and

N: To play.

x: To stop.

m: To rewind.

M: To fast-forward.

z NREC: To record, press

while pressing zREC.

4To switch the antenna output.

6To expose the on-screen

display.

8To move the cursor upward,

downward, to the left, or to the

right.

9To call up the MENU display.

qs and qd

To change the channel. For

example, to change to channel

5, press (or press and0 and 5 5

ENT).

qf CH+: Channel up.

CH–: Channel down.

qg To change the input mode.

qk To enter the selection.

qh To operate JUMP FLASHBACK,

or CHANNEL RETURN function

on the TV depending on the

setting of the TV’s

manufacturer.

Operating a DVR (Digital video recorder)

3(*2LIST)

To call up the title of the

recorded program.

4To switch the output of the SAT

receiver to the TV.

(When connecting a TV cable or

antenna to the receiver, the

output switches between a TV

and SAT program.)

(*2THUMBS+)

To select the desired recorded

program.

(It is necessary to have

recorded the desired program.)

6To turn on the display.

(*2THUMBS–)

To select the desired recorded

program.

(It is necessary to have

recorded the desired program.)

8To move the cursor upward,

downward, to the left, or to the

right.

9To call up the MENU display.

(*2EPG)

To access to all aspects of the

service.

0 ql, and

N: To play.

m: To rewind.

M: To fast-forward.

z NREC: To record, press

while pressing zREC.

First release , thenN

release zREC. To stop

recording, perform the

same procedure.

x: To stop.

X: To pause.

qs and qd

To change the channel.

For example, to change to

channel 5, press and (or,0 5

press .)5 and ENT

qf CH+: Channel up.

(*2PAGE+) Page up.

CH–: Channel down.

(*2PAGE–) Page down.

qg To clear the setting.

To exit the setting menu.

qh (*2REPLAY)

To replay.

Or to go into REC/REVIEW

mode during play. (After about

5-second rewind, replay

begins.)

qj To bring up Master Guide.

(*2Live TV)

To bring up Master Guide.

qk To bring up the Station Index

when a program guide is not

displayed.

To select the channel that is

highlighted.

*2This key corresponds to Tivo service or the replay service. Refer to its

instruction manual for details.

Operating a digital cable box

3To use the “FAVORITE” function.

4To switch the output of the SAT

receiver to the TV .(When

connecting a TV cable or

antenna to the receiver, the

output switches between a TV

and SAT program.)

6To turn on the display.

8To move the cursor upward,

downward, to the left, or to the

right.

9To call up the MENU display.

0 ql, and

*3N: To play.

*3m: To rewind.

*3M: To fast-forward.

*3zREC:

To record, press N

while pressing zREC.

First release , thenN

release zREC. To stop

recording, perform the

same procedure.

*3x: To stop.

*3X: To pause.

qs and qd

To change the channel.

(for example, to change to

channel 5, press , or0 and 5

press .)5 and ENT

qf CH+: Channel up.

CH–: Channel down.

qg To exit the setting menu.

qh To turn on the display of a

shortcut menu.

qj To call up the title bar and

toggle the title bar on/off in

CABLE mode.

qk To bring up the Station Index

when a program guide is not

displayed.

To select the channel that is

highlighted.

*3The operation of the built-in DVR or the video on demand.

Operating a DAT deck

3To select numbers 10 and

above. For example, to select

track 15, press PIP and then

press .5

6To change the display mode or

turn the display on/off.

q; To record, press N while

pressing zREC/First release

N z, then release REC.

qs To select the track number. 0

selects track 10. To select track

numbers above 10, see the

descriptions on the PIP button

above.

qf CH+: To select the next track.

CH–: To select the previous

ql N: To play.

m: To rewind.

M: To fast-forward.

x: To stop.

X: To pause.

Operating a CD player

3To select numbers 10 and

above. For example, to select

track 15, press PIP and then

press .5

6To switch the display of the CD

player to on/off.

qs To select the track number. 0

selects track 10. To select track

numbers above 10, see the

descriptions on the PIP button

above.

qd To enter the setting.

qf CH+: To select the next track.

CH–: To select the previous

track.

qg To clear the setting.

qh To select next disc.

ql N: To play.

m: To rewind.

M: To fast-forward.

x: To stop.

X: To pause.

Operating an MD deck

3To select numbers 10 and

above. For example, to select

track 15, press PIP and then

press .5

6To switch the display of the CD

player to on/off.

q; To record, press N while

pressing zREC/First release

N z, then release REC.

qs To select the track number. 0

selects track 10. To select track

numbers above 10, see the

descriptions on the PIP button

above.

qd To enter the setting.

qf CH+: To select the next track.

CH–: To select the previous

track.

qg To clear the setting.

qh To select next disc.

ql N: To play.

m: To rewind.

M: To fast-forward.

x: To stop.

X: To pause.

Operating a digital satellite receiver

3To use the “FAVORITE”

function.

4To switch the output of the

digital satellite receiver to the

TV. (When you connect a TV

cable or antenna to the receiver,

the output switches between a

TV and SAT program.)

8To scroll through the Master

Guide.

9To call up the MENU display.

qs and qd

To change the channel. For

example, to change to channel

5, press and (or press and0 5 5

ENT).

qf Channel up: +

Channel down: –

To page through the guide

when a program guide is

displayed.

qg To bring up the Station Index.

qh To tune to the last tuned

station.

qj To bring up the Master Guide.

qk To select the channel that’s

highlighted. To bring up the

Station Index when a program

guide is not displayed

ql N: To exit the mode.

Operating a receiver/amplifier

4To switch input source by each

pressing.

qs To select the input source:

1 selects VIDEO 1

2 selects VIDEO 2

3 selects AUX

4 selects TUNER

5 selects CD

6 selects TAPE

7 selects MD

8 selects TV

9 selects PHONO

0 selects DVD

qf Presetting frequency up: ,+

down: –

Tuning frequency up: +,

down: –

qh To shift band (FM/AM).

ENT

DVD RCVR

VCR CBL / SAT

Operating a DVD

3To select numbers 10 and

above. For example, to select

track 15, press PIP and then

press .5

4To change the sound.

6To show the current play status

on the screen.

8To move the cursor upward,

downward, to the left, or to the

right.

9To display the DVD menu.

q; To record, press N while

pressing .zREC

First release , then releaseN

zREC.

qs Number buttons : To set items

selected from the screen.

qd To enter the setting. To set

items selected from the screen.

qf CH+: To proceed to the next

location or song.

Channel up.

CH–: To proceed to the

previous location or song.

Channel down.

qg To switch the subtitle.

qh To display the title menu.

qj To clear the selected characters

from the screen.

qk To execute items selected from

the screen.

ql N: To play.

m: To rewind.

M: To fast-forward.

x: To stop.

XTo pause.

Your Code Number

035

Produkt Specifikationer

Mærke:	Sony
Kategori:	Fjernbetjening
Model:	RM-V302

Har du brug for hjælp?

Hvis du har brug for hjælp til Sony RM-V302 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Fjernbetjening Sony Manualer

16 September 2024

15 September 2024

14 September 2024

9 September 2024

2 September 2024

2 September 2024

2 September 2024

2 September 2024

2 September 2024

Sony RM-VS10TV Manual

2 September 2024

Fjernbetjening Manualer

Nyeste Fjernbetjening Manualer

Nanlite BT-BCS-48V3.5mm Manual

21 December 2024

SMK-Link VP3700 Manual

17 December 2024

Metronic ZAP 2 Unic - 495399 Manual

17 December 2024

Metronic ZAP 3 - 495373 Manual

17 December 2024

Metronic ZAP 3 - 495309 Manual

17 December 2024

Metronic ZAP 3 - 495308 Manual

17 December 2024

Metronic 495390 Manual

17 December 2024

Metronic 495387 ZAP 3 Manual

17 December 2024

Metronic ZAP 6 Manual

17 December 2024

EQ-3 HM-RC-19-B Manual

16 December 2024