Sony RM-V50T Manual

Sony Fjernbetjening RM-V50T

Læs nedenfor 📖 manual på dansk for Sony RM-V50T (2 sider) i kategorien Fjernbetjening. Denne guide var nyttig for 29 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

RM-V50T.3-856-752-12 (1). NO.1

3-856-752-12 (1)

Setting up the

Remote Commander

Before you can start using the Remote Commander,

you must ﬁrst set it up. This manual describes

everything you need to know to set up the

Commander.

About Presetting the

Commander

This Remote Commander is preset at the factory to

operate Sony brand TVs (using code No. 01) and

Sony brand VHS VCRs (using code No. 03). If

you’re using this Commander with a Sony TV and

a Sony VHS VCR, you won’t need to preset the

Commander before you start using it.

If you use this Remote Commander with other

(non-Sony) manufacture’s TVs and VCRs, or the

Remote Commander cannot operate even a Sony

TVs and VCRs, you’ll need to follow the

instructions in this manual to preset the Remote

Commander with the correct code number for your

TV and VCR.

Note

The Commander can be set up to operate only one

component of each category (TV or VCR) at a time-unless

their code numbers happen to be the same. For example,

you cannot set up the Commander to operate a Sony TV

and a Panasonic TV at the same time (because they use

diﬀerent code numbers).

Setting the Code

Step 1: Entering the Code

Number

1Refer to “Component Code Numbers”, and ﬁnd

the two-digit code number for your component.

If more than one code number is listed, use the

number that’s listed ﬁrst to complete the steps

that follow.

For example, if you’re setting up a Philips’ TV,

you would use code number .11

If your component is not listed, see “Searching

for the Correct Code”.

2While pressing , press SET VCR TVor .

3Enter the component’s code number.

For example, if you’re entering the code for a

Philips’ TV, you would press and release 1,

then press and release 1.

English 4Press and release the … button.

The code number is entered and a long beep

sounds.

Note

When you fail to enter the code, a short beep sounds.

5Go to “Step 2: Checking if the Code Number

Works” to ﬁnish setting up.

If you press a wrong button in Step 3

Press the button and then go back to Step 2.…

Step 2: Checking if the Code

Number Works

1Power on the component you want to set up

with its power switch.

2Aim the Remote Commander at the component

and press the button.u

The component should power oﬀ.

3When the component powers oﬀ, check that the

Commander is operating the other functions of

your component, such as programme and

volume control.

If the Commander Doesn’t Seem to Be

Working...

• First, try repeating these setup procedures using

the other codes listed for your component (See

“Component Code Numbers”).

• If–after trying all the codes listed for your

component–you still cannot get the Commander

to work properly, try the search method described

under “Searching for the Correct code.”

If the Commander Seems to Be Working

Properly...

• You’re ﬁnished setting up the Commander for

this component.

• If you’re setting up more than one component,

you’ll need to complete these procedures for each

component you plan to use with the Commander.

Searching for the Correct

Code

If you’ve tried all the code numbers listed for your

component and you still cannot get the

Commander to work (or if your component is not

listed in this manual), try these steps.

1Power on the component you want to set up

with its power switch. Then while pressing

SET VCR TV, press or .

2Press and release the button. ThenPROGR +

press and release the button.u

3Repeat step 2 until your component powers oﬀ.

Pressing PROGR + and u repeatedly will try

every available code until the correct one is

found. Be patient as you do this; it may take up

to about 90 tries until the correct code is

located.

4When the component powers oﬀ, press and

release the button to store the code number…

in the Commander’s memory.

5Check that the Commander is operating the

other functions of your component. Turn on

the component again; then press the

programme and volume control buttons. If the

Commander seems to be working properly,

you’re done setting up the Commander.

If you still cannot get the Commander to work

properly, see “Troubleshooting”.

Using the Remote

Commander

Operating a Component

1Press or , which you want to operate.VCR TV

2Point the Commander directly at the

component.

3Press the button for the function you want to

use.

See “Remote Button Descriptions” for complete

descriptions of the buttons on the Commander.

Using Fastext

With Fastext you can access pages with one key

stroke. When a Fastext page is broadcast, a colour-

coded menu will appear at the bottom of the screen.

The colours of this menu correspond to the red,

green, yellow and blue buttons on the Remote

Commander.

Press the coloured button which corresponds to the

coloured-coded menu. The page will be displayed

after some seconds.

Releasing the Beep Function

While pressing the button, press the – button.u Á

To operate this function again, press + buttonÁ

while pressing the u button.

Note on Using the Remote Commander

Using this Commander will not increase the functions of

your TV or VCR. The functions of the Commander are

limited to the functions of the TV or VCR itself. For

example, if your TV does not have a mute function, the ¤

button on this Commander will not function with your TV.

Remote Button

Descriptions

When operating the TV, a short beep sounds once

and when operating the VCR, a short beep sounds

twice when pressing the button.

OK?

While pressing

SET, press VCR

or TV.

Aim at your

component.

Enter code.

Done

YES

Brand

Philips

Code No.

11, 12, 13, 17

Component

Remote

Button

Operates

TV,VCR

VCR

TV, VCR

VCR

Function

Used to switch to VCR

or TV operation.

Used for setting up the

Commander to operate

your TV and VCR.

Turns on and oﬀ the

VCR.

Turns oﬀ the TV.

Changes the input

mode.

Switches the signals

supplied to the TV

(from the antenna or

from the VCR)

Switches to the Teletext.

Switches to the TV.

Turns on the TV.

Changes the

programme. You can

also turns on the TV

with these buttons.

To select a double-digit

programme number,

press this button and

then the numbers. To

select a number between

10 and 19, press this

button (1-) and a

number button.

To select a number

between 20 and 29,

press this button (2-)

and a number button.

Rewind

Fastext button, see the

left. (red)

Play

Fastext button, see the

left. (green)

Remote

Button

Operates

VCR

TV, VCR

Function

Fast-forward

Fastext button, see the

left. (yellow)

Record

To record, press (

while pressing r.

Stop

Fastext, see the left.

(blue)

Pause

Mutes volume on TV.

Press again to turn

muting oﬀ.

Volume up: +

Volume down: –

Programme up: +

Programme down: –

Component Code

Numbers

RM-V50T

Operating Instructions

Mode d’emploi (face arrière)

Remote Commander

Brand

Sony

Aiwa

Akai

Alba

Audio sonic

Baird

Bestar

Blaupunkt

Blue sky

Braudt

Brionvega

Bush

CGM

Clatronic

Crown

Daewoo

Dual

Fenner

Ferguson

First line

Fisher

Fraba

Funai

Goldstar

Goodmans

Grundig

Hitachi

Hyper

ICE

Inno-Hit

Irradio

Code No.

01, 02, 03, 04, 05

01, 07 (VTR 1: Betamax)

02, 08 (VTR 2: 8 mm)

03, 09 (VTR 3: VHS)

04 (VTR 4: VD)

05 (VTR 5: VD)

06 (VTR 6: VD)

56, 61

34, 43, 41

81, 62

49, 42

24, 26

18, 30

48, 46

81, 75, 62

46, 15, 44, 45

TV27&VCR15

11, 12

22, 33, 65

11, 67, 74

58, 57

TV74&VCR57

11, 47

68, 06

66, 38, 42, 41, 37

23, 24

09, 15, 16, 11

52, 46

TV54&VCR52

62, 09, 11, 12, 37, 13, 75

58, 12

24, 25, 07

15, 21

TV07&VCR15

52, 53

47, 35, 48

23, 06

Component

VCR

COMB*

VCR

COMB*

VCR

COMB*

VCR

COMB*

VCR

Replacing the

Lithium Battery

If the Remote Commander does not operate

properly, the lithium battery may be worn out.

Replace the lithium battery with a Sony CR2032

lithium battery.

Note

If you take time to insert the lithium battery or press the

buttons when replacing the lithium battery, the code

numbers that you entered will be erased.

Notes on lithium battery

• Keep the lithium battery out of the reach of children.

Should the battery be swallowed, immediately consult a

doctor.

• Wipe the battery with a dry cloth to assure a good

contact.

• Be sure to install the battery with the correct polarity.

• Do not hold the battery with metallic tweezers as doing

so may cause a short-circuit.

• Use of other batteries than the CR2032 may cause a risk

of ﬁre or explosion.

WARNING

Battery may explode if mistreated. Do not

recharge, disassemble or dispose of in ﬁre

Troubleshooting

If you’re having problems setting up or using the

Remote Commander:

• When setting up the Commander, carefully go

through the procedures described under “Setting

the Code”. If the code that’s listed ﬁrst for your

component doesn’t work, try all the codes for

your component–in the order in which they’re

listed. If all the codes fail to work (or if your

component is not listed in this manual), try using

the procedures under “Searching for the correct

code.”

• Check that you’re aiming the Commander

directly at the component, and that there are no

obstructions between the Commander and the

component.

• Make sure the battery you’re using is not worn

out, and that it is inserted correctly.

Speciﬁcations

Operable distance

Approx. 5 m (16.4 ft) (varies depending

on the component)

Power requirements

DC3V (one Sony CR2032 lithium battery)

Battery life Approx. 6 months (varies depending on

frequency of use)

Dimensions Approx. 59 × × 162 21 mm (w/h/d)

(2 3/ 8× 6 1/ 2×27 /32 in.)

Mass Approx. 50 g (1.76 oz.) (including

battery)

Design and speciﬁcations are subject to change

without notice.

It will be useful to write down the code numbers of

your components in the chart above, so that you

can refer to them when registering the code

numbers with the Commander.

Coin

Rear

Positive side

Rear

Component

VCR

No.

REC

Brand

Itt/Nokia

JVC

Kendo

Loewe

Luxor

Mark

Matsui

Medion

Mitsubishi

Mivar

NEC

Nokia

Oceanic

Nordmende

Okano

Onwa

Orion

Panasonic

Philips

Phonola

Pioneer

Radio

Radiola

Roadstar

SABA

Samsung

Sanyo

Schneider

SEG

Seleco

Sharp

Siemens

Sinudyne

Tandberg

Tatung

Teac

Telefunken

Thomson

Thorn

Toshiba

Universum

W. W. House

Watson

Component

VCR

COMB*

VCR

COMB*

VCR

COMB*

VCR

COMB*

VCR

COMB*

VCR

COMB*

VCR

COMB*

VCR

COMB*

VCR

COMB*

Code No.

34, 35

62, 77, 78

64, 59, 65, 66

TV54&VCR52

09, 15, 16

27, 52, 12

TV09&VCR12

TV15&VCR12

TV16&VCR12

20, 45

63, 11, 65

TV68&VCR57

73, 33, 56, 76, 05

46, 36

TV52&VCR38

71, 72, 69, 70

62, 63

29, 27, 28

18, 19, 45, 36, 35, 34

32, 49

36, 35

44, 39, 40

24, 23, 22

09, 68

36, 34, 37

10, 49, 50

TV51&VCR38

79, 80

28, 31

11, 12, 13, 17

18, 12, 17, 19

TV11&VCR12

11, 13

14, 12, 13

39, 31, 40, 44, 42, 37, 41

24, 60

16, 14, 15

53, 55, 56, 61, 54

TV12&VCR54,

TV60&VCR55,

TV60&VCR53

49, 50

11, 09, 64, 47

12, 20

TV11&VCR12

30, 45

45, 41

24, 25

20, 49

32, 40, 39, 43

25, 26

37, 42

49. 52

57, 58

11, 21, 18

26, 40, 52

11, 68, 47, 12

14, 38

TV51&VCR38

Produkt Specifikationer

Mærke:	Sony
Kategori:	Fjernbetjening
Model:	RM-V50T

Har du brug for hjælp?

Hvis du har brug for hjælp til Sony RM-V50T stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Fjernbetjening Sony Manualer

16 September 2024

15 September 2024

14 September 2024

9 September 2024

2 September 2024

2 September 2024

2 September 2024

2 September 2024

2 September 2024

Sony RM-VS10TV Manual

2 September 2024

Fjernbetjening Manualer

Nyeste Fjernbetjening Manualer

Nanlite BT-BCS-48V3.5mm Manual

21 December 2024

SMK-Link VP3700 Manual

17 December 2024

Metronic ZAP 2 Unic - 495399 Manual

17 December 2024

Metronic ZAP 3 - 495373 Manual

17 December 2024

Metronic ZAP 3 - 495309 Manual

17 December 2024

Metronic ZAP 3 - 495308 Manual

17 December 2024

Metronic 495390 Manual

17 December 2024

Metronic 495387 ZAP 3 Manual

17 December 2024

Metronic ZAP 6 Manual

17 December 2024

EQ-3 HM-RC-19-B Manual

16 December 2024