Sony YT-ICB45 Manual


Læs nedenfor 📖 manual på dansk for Sony YT-ICB45 (1 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 3 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/1
3-217-488- (1)01
Sony Corporation 2007 Printed in China
In-Ceiling Bracket
Installation Instructions
A
C
D
E
Fixing
plate /
Fixing
plate /
10 to 35 (13/32
to 1 7/16) /
Ceiling /
φ
227 to 231 (9 to 9 1/8) hole / Ceiling /
Unit: mm (inches) /
11 (
7
/
16
)
Ceiling:
φ
227 to 231 (9 to 9 1/8) hole / Thickness of the ceiling:
10 to 35 (13/32 to 1 7/16) /
100 (4)
54 (2
1
/
4
)
φ
270 (10 3/4)
Unit: mm (inches) /
English
WARNING
• This installation should be made by a qualified service person
and should conform to all local codes.
• Ensure that the installation location and its material are strong
enough to withstand the gross weight of the camera and the In-
Ceiling Bracket, and then install the camera securely. If they are
not strong enough, the camera may fall and cause serious injury.
• To prevent the camera from falling, be sure to attach the wire
rope supplied with the camera.
• If you install the camera at a height, check periodically, at least
once a year, to ensure that the connection has not loosened. If
conditions warrant, perform this periodic check more frequently.
CAUTION
Check that the thickness of the ceiling is from 10 mm (
13/32
inches) to 35 mm (1 7/16 inches) inclusive.
Make a ø229 ± 2 mm (9 1/8 ± 13/16 inches) hole in the ceiling.
Do not scratch your hands on the sharp edges; this may cause
injury.
Before attempting installation, wear gloves to prevent injury.
Overview
The YT-ICB45 is an in-ceiling bracket designed for use with Color
Video Cameras. It is used when the body of the camera is embedded in
the ceiling, or with gypsum or plaster boards, where the quality of the
material used in the ceiling makes it difficult for ordinary screws to hold.
Installable cameras
Installing the In-Ceiling Bracket
1Make a ø 229 ± 2 mm (9 1/8 ± 13/16 inches) hole in the ceiling.
Use the supplied template. The four slotted holes on the template
are usable when you decide the center position of the camera.
2Remove the dome casing from the camera.
For details, refer to the Installation Manual or the Operating Instructions
of the camera.
3Connect the cables to the camera.
4Remove the screws from the left and right side brackets (2 screws
each) and fix the removed screws in the lower screw holes. (Fig.
A)
5Using the supplied M4 screws, attach the In-Ceiling Bracket to the
camera’s unit casing or to the bracket supplied with the camera.
Attach the cameras unit casing to the In-Ceiling Bracket using two
M4 screws. (Fig. B)
For details, refer to the Installation Manual or the Operating Instructions
of the camera.
Note
When attaching, align the center of the hole on the In-Ceiling
Bracket with the center of the bottom of the camera or the center of
the bracket supplied with the camera. The cover of the In-Ceiling
Bracket may not be attached if the centers are misaligned.
6Be sure that the right and left fixing plates of the In-Ceiling Bracket
stay in the lengthwise position (factory setting), and install the In-
Ceiling Bracket with the camera on the ceiling. (Fig. C)
7Tighten the left and right screws of the In-Ceiling Bracket to secure
it to the ceiling.
As you tighten the screws, the fixing plates swing outward and
lower to grip the ceiling. (Fig. D)
Be sure that the fixing plates grip the ceiling firmly.
Note
Torque the screws to 1.47 N m (15 kgf cm) or less to tighten them.• •
Tightening the screws too hard may cause damage to the In-
Ceiling Bracket.
8Remove the slit cover, and adjust the shooting direction and range
of the camera.
After the adjustment, replace the slit cover.
For details, refer to the Installation Manual or the Operating Instructions
of the camera.
9Attach the dome casing to the cameras unit casing.
For details, refer to the Installation Manual or the Operating Instructions
of the camera.
10Attach the cover of the In-Ceiling Bracket. (Fig. E)
Attach the cover while turning it so that the projections inside the
cover are inserted in the bracket, and tighten the two screws on
the cover.
Removing the In-Ceiling Bracket
Loosen the two screws on the cover and turn the cover to remove it.
Loosen the right and left screws of the In-Ceiling Bracket until the fixing
plates swing back lengthwise. Then remove the In-Ceiling Bracket and
the camera.
Notes
Remove the cover vertically.
Torque the screws to 1.47 N• •m (15 kgf cm) or less to loosen them.
Loosening the screws with excessive force may cause damage to the
In-Ceiling Bracket.
Hold the camera while loosening the screws; otherwise the In-Ceiling
Bracket and the camera may fall.
Specifications
Mass Approx. 850 g (1 lb 17 oz)
Dimensions See Figure F.
Supplied accessories Template (1), M4 screws (4),
Installation Instructions (1)
F
Fixing
plate /
M4 screws /
B
Color Video Camera SSC-CD45P, SSC-CD47P, SSC-CD49P
YT-ICB45


Produkt Specifikationer

Mærke: Sony
Kategori: Ikke kategoriseret
Model: YT-ICB45

Har du brug for hjælp?

Hvis du har brug for hjælp til Sony YT-ICB45 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Sony Manualer

Sony

Sony BP-L60S Manual

11 Oktober 2024
Sony

Sony BP-U100 Manual

11 Oktober 2024
Sony

Sony BC-L500 Manual

11 Oktober 2024
Sony

Sony BP-GL95A Manual

11 Oktober 2024
Sony

Sony BP-U35 Manual

11 Oktober 2024
Sony

Sony BC-L70 Manual

11 Oktober 2024
Sony

Sony AC-DN1 Manual

11 Oktober 2024
Sony

Sony BC-L160 Manual

10 Oktober 2024
Sony

Sony BC-L90 Manual

10 Oktober 2024
Sony

Sony BP-GL95 Manual

1 Oktober 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Kramer

Kramer VP-8X8 Manual

25 November 2024
Kramer

Kramer PT-2C Manual

25 November 2024
Lazer

Lazer Bob+ Manual

25 November 2024
Dometic

Dometic DPS 80 Manual

25 November 2024
Kramer

Kramer 102MX Manual

25 November 2024
Kramer

Kramer FC-18 Manual

25 November 2024
Kramer

Kramer DSP-62-UC Manual

25 November 2024
Tiger

Tiger SKF-H101 Manual

25 November 2024