Soundmaster PL875USB Manual

Soundmaster Pladespiller PL875USB

Læs nedenfor 📖 manual på dansk for Soundmaster PL875USB (12 sider) i kategorien Pladespiller. Denne guide var nyttig for 15 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/12

PL87 USB5

DEUTSCH

ENGLISH

FRANÇAIS

NEDERLANDS

ESPAÑOL

This symbol indicates the presence of dangerous

voltage inside the enclosure, sufficient enough to

cause electric shock.

This symbol indicates the presence of important

operating and maintenance instructions for the

device.

Safety, Environmental and Setup Instructions

x Use the device in dry indoor environments only.

x Protect the device from humidity.

x Do not open the device. RISK OF ELECTRIC SHOCK! Refer opening and servicing to qualified personnel.

x Connect this device to a properly installed and earthed wall outlet only. Make sure the mains voltage corresponds with

the specifications on the rating plate.

x Make sure the mains cable stays dry during operation. Do not pinch or damage the mains cable in any way.

x A damaged mains cable or plug must immediately be replaced by an authorized service center.

x In case of lightning, immediately disconnect the device from the mains supply.

x Children should be supervised by parents when using the device.

x Clean the device with a dry cloth only.

Do NOT use CLEANING AGENTS or ABRASIVE CLOTHS!

x Do not expose the device to direct sunlight or other heat sources.

x Install the device at a location with sufficient ventilation in order to prevent heat accumulation.

x Do not cover the ventilation openings!

x Install the device at a safe and vibration-free location.

x Install the device as far away as possible from computers and microwave units; otherwise radio reception may be

disturbed.

x Do not open or repair the enclosure. It is not safe to do so and will void your warranty. Repairs only by authorized

service/ customer center.

x The device is equipped with a “Class 1 Laser”. Avoid exposure to the laser beam as this could cause eye injuries.

x Only use mercury and cadmium-free batteries.

x Used batteries are hazardous waste and NOT to be disposed of with the household waste!!! Return the batteries to your

dealer or to collection points in your community.

x Keep batteries away from children. Children might swallow batteries. Contact a physician immediately if a battery was

swallowed.

x Check your batteries regularly to avoid battery leakage.

CLASS 1 LASER PRODUCT

KLASSE 1 LASER PRODUKT

LUOKAN 1 LASER LAITE

KLASS 1 LASER APPARAT

PRODUCTO LASER CLASE 1

CAUTION - INVISIBLE LASER RADIATION WHEN OPENING

THE COVER OR PRESSING THE SAFETY INTERLOCK. AVOID

EXPOSURE TO THE LASER BEAM.

ENVIRONMENTAL PROTECTION

Do not dispose of this product with the normal household waste at the end

of its life cycle. Return it to a collection point for the recycling of electrical

and electronic devices. This is indicated by the symbol on the product,

user manual or packaging.

The materials are reusable according to their markings. By reusing, recycling or

other forms of utilization of old devices you make an important contribution to

the protection of our environment.

Please contact your local authorities for details about collection points.

WARNING

Risk of electric shock

Do not o

en!

Caution: To reduce the risk of electric shock, do not remove the cover (or back). There

are no user serviceable parts inside. Refer servicing to qualified service personnel.

Used batteries are hazardous waste and NOT to be disposed

of with the household waste! As a consumer you are legally

obligated to return all batteries for environmentally responsible

recycling – no matter whether or not the batteries contain harmful

substances*).

Return batteries free of charge to public collection points in your

community or to shops selling batteries of the respective kind.

Only return fully discharged batteries.

*) marked Cd = cadmium, Hg = mercury, Pb = lead

E-1

LOCATION OF CONTROLS

1) DUST COVER

2 ) LCD DISPLAY

3 ) CD TRAY OPEN/CLOSE BUTTON

4 ) CD TRAY

5) 3.5MM AU IN ACKX J

6) 3.5MM HEADPHONE JACK

7 ) PANEL COVER

8 ) USB SOCKET

9 ) SD/MMC CARD SLOT

1 )0 STANDBY LED INDICATOR

11) POWER ON/STANDBY BUTTON

1 )2 FUNCTION BUTTON

1 )3 MEMORY/CLOCK-ADJUST BUTTON

1 )4 FOLDER/PRE-UP BUTTON

1 )5 RECORD BUTTON

1 ) E6 JECT BUTTON

1 ) /7 BAND PLAY/PAUSE BUTTON

1 )8 TUNING/SKIP UP /

1 )9 STOP BUTTON

20) TUNING/SKIP DOWN BUTTON

2 1) ST/MONO-PLAY MODE BUTTON

22) PRESET EQ BUTTON

23 ) VOLUME UP/DOWN BUTTON

24) REMOTE SENSOR

25) SPINDLE ADAPTOR

26 ) STROBE ILLUMINATOR

27) ALIGNMENT SCREW WITH RUBBER COVER

28) COUNTER WEIGHT

29) ANTISKATING

30) CUEING LEVER

3 1) TONE-ARM LOCK

32) TURNTABLE SPEED SELECTOR

33) PITCH AD USTMENTJ

34) SPEAKER TERMINAL (L/R)

35) LINE OUT SOCKET (L/R)

36) 75 OHM FM SOCKET

37) AC CORD

CAUTION:

USAGE OF CONTROLS OR AD USTMENTS OR J PERFORMANCE OF PROCEDURES OTHER THAN THOSE

SPECIFIED HEREIN MAY RESULTE ARDOUS RADIATION POSURE. IN HAZ XE

THIS J UNIT SHOULD NOT BE AD USTED OR REPAIRED BY ANYONE CEPT QUALIFIED SERVICE XE

PERSONNEL.

PRECAUTIONS FOR USE

INSTALLATION

• UNPACK ALL PARTS AND REMOVE MATERIAL. PROTECTIVE

• DO NOT CONNECT THE UNIT TO THE MAINS BEFORE CHECKING THE MAINS VOLTAGE AND BEFORE

ALL OTHER CONNECTIONS HAVE BEEN MADE.

• DO NOT COVER ANY VENTS AND MAKE SURE THAT THERE IS A SPACE OF SEVERAL CENTIMETERS

AROUND THE UNIT FOR VENTILATION.

INSTALLATION OF COUNTER WEIGHT

1. SLIDE IN COUNTER WEIGHT THE COMPLETELY INTO THE REAR OF THE TONE ARM UNTIL IT REACH

THE TURN ENDˈ IT CLOCKWISE UNTIL IT CLICK WITH PIT INSIDE.

2 . TWIST THE COUNTER WEIGHT CLOCKWISE & BACKWARD UNTIL IT REACH THE WHITE LINE AS FIGURE

3 . TWIST THE COUNTER MARKING UNTIL IT REACH “ 1 “ POSITION

4 . TWIST THE COUNTER WEIGHT ANTI-CLOCKWISE & INWARD UNTIL IT REACH THE APPROPIATE

WORKING PRESSURE.

E-2

REMARK : THE WORKING PRESSURE OF THE Y PROVIDED ST LUS IS FROM THE RANGE 4 – 6 GRAMS

ACCORDING TO THE CARTRIDGE MANUFACTURER. ALL Y ST LUS HAS IT OWN WORKING

PRESSUE AND PLEASE REFER TO THE SPECIFICATION RESPECTIVELY.

CONNECTION

1. CONNECT THE POWER CORD AC OUTLET AND CONNECT SPEAKER WIRE (37) TO THE TO THE

SPEAKER TERMINAL (34) LOCATED ON THE UNIT. REAR SIDE OF

2 . PRESS THE POWER BUTTON (11) AND STANDB IF Y LED INDICATOR (1 LIGHT OFF, IT MEAN 0 ) ’ S THE

POWER SUPPL Y IS NORMAL. NOW OUR PLA Y YS STEM IS READY TO Y THE MUSIC.

SETTING THE CLOCK

1. SET UNIT IN STANDB Y MODE.

2 . PRESS & HOLD THE 3 “MEM/CLK-ADJ” BUTTON (1 ), THE LCD DISPLAY ( ) WILL SHOW “ SET CLOCK “2 AND

THEN DISPLAY “ 1 “ 2HR OR HR 24 PRESS SKIP OR SKIP BUTTON (1 SELECT 8 /20) TO THE

APPROPIATE AREA HOUR FORMAT(12HR/ HR). (124 PRESS “MEM/CLK-ADJ” BUTTON 3 ) AGAIN TO

CONFIRM.

3 2 . THE LCD ( ) WILL DISPLAY THE FIRST & SECOND DIGIT OF “00” IS FLASHING. SKIP PRESS OR

SKIP BUTTON / ) (18 20 TO SET THE CORRECT 3 HOUR. PRESS ”MEM/CLK-ADJ” BUTTON (1 ) TO STORE

THE CORRECT HOUR.

4 . THE THIRD FOURTH DIGIT OF IS FLASHING, PRESS & “00” THE SKIP OR SKIP BUTTON (18 /20) TO

SET THE CORRECT MINUTES. THEN 3 PRESS “MEM/CLK-AD (1J” ) TO STORE THE CORRECT MINUTE.

¾ THE PRE-SET TIME WILL BE RE-SET COMPLETELY IF DIS-CONNECTING THE MAIN POWER

SUPPLY. YOU ARE RECOMMENDED SWITCH TO THE STEM INTO STANDB YS Y MODE FOR

CONVENIENCE USAGE.

LISTENING TO RADIO

MANUAL TUNING

1. PRESS (1 ) FUNCTION BUTTON 2 TO SELECT “ TUNER MODE. ”

2 . PRESS “BAND / ” BUTTON 7 (1 ) TO SELECT DESIRED BAND (MW OR FM).

3 . TUNE TO THE REQUIRED STATION PRESSING THE TUNING SKIP UP BY “ / 8 OR DOWN (1 /20)

BUTTON.

4 J . AD UST VOLUME CONTROL (23) TO THE DESIRED VOLUME LEVEL.

AUTO TUNING

1. PRESS FUNCTION BUTTON (1 ) 2 TO SELECT “ TUNER “ MODE

2 . PRESS “ BAND / ” BUTTON (17 ) AND SELECT THE DESIRED BAND (MW (AM) OR FM).

3 . PRESS AND HOLD THE “ SKIP / TUNING UP 8 OR DOWN (1 /20) BUTTON FOR 1- SECONDS2 AND

THEN RELEASE

4 . THE UNIT WILL START SEEKING AUTOMATICALLY AND STOP UNTIL A RADIO STATION IS REACHED.

5 . REPEAT UNTIL STEP 3 & 4 THE DESIRED RADIO STATION IS BEING REACHED.

6 J . AD UST VOLUME UP/DOWN CONTROLS (23) TO THE DESIRED VOLUME LEVEL.

PRESET STATIONS

Y OU CAN STORE UP TO TOTAL OF 40 RADIO STATIONS (30 FM,10 AM) IN THE MEMORY.

1. SET TO “ TUNER “ MODE

2 . TURN TO THE DESIRED RADIO STATION MANUAL OR “AUTO BY “” ” TUNING METHOD.

3 3 . PRESS “ MEM / CLK-ADJ” BUTTON (1 ) TO ENABLE PROGRAM STATE.

4 . PRESS “ FOLDER / PRE-UP 4 (1 ) OR FOLDER / PRE-DOWN BUTTON (AT HANDSET) REMOTE TO

SELECT THE DESIRED STATION POSITION MEMORY FOR STORAGE.

5 3 . PRESS “MEM / CLK-ADJ ” BUTTON (1 ) AGAIN TO CONFIRM THE SETTING.

6 . REPEAT STEP 2 TO 5 TO STORE OTHER STATIONS.

7 . PRESS “ FOLDER / PRE-UP OR DOWN “ BUTTON AT REMOTE HANDSET TO SELECT THE PRESET

STATIONS IN ORDER.

8 . TO RETURN NORMAL TUNER MODE, LEAVE KE FREE. Y S

E-3

¾THE PRE-SET MEMORIES WILL BE CANCELLED COMPLETELY IF SWITCHING OFF THE MAIN POWER

BUTTON ON SYSTEM. OU Y ARE RECOMMENDED TO SWITCH THE SYSTEM INTO STANDBY MODE FOR

CONVENIENCE USAGE.

¾ YOU CAN OVERWRITE A PRESET STATION STORING BY ANOTHER FREQUENC IN ITS PLACE. Y

FM & FM-STEREO RECEPTION

z PRESS THE 2“ FM-ST/MONO ” BUTTON ( 1)REPEATEDLY, FM IN THE PROGRAMS ARE RECEIVING MONO

AND STEREO MODE REPEATEDL Y. IN PARTICULAR WHEN STEREO SIGNALS ARE WEAK. IT IS

PREFERABLE RECEIVE TO THE PROGRAM MONO. IN

z IF STEREO SIGNAL IS BEING RECEIVED, THE “ST” INDICATOR “ ” WILL APPEAR ON LCD DISPLAY

( )2 TO SHOW FM STEREO PROGRAM IS NOW RECEIVING.

HINTS FOR BEST RECEPTION:-

- : A AM THE RECEIVER HAS BUILD-IN AM BAR ANTENNA. IF AM RECEPTION IS WEAK, SLIGHT ROTATE

OR RE-POSITIONING OF THE UNIT WILL USUALLY IMPROVE THE AM RECEPTION.

- FM : A THE RECEIVER HAS BUILD-IN FM WIRE ANTENNA (36) HANGING AT THE REAR CABINET. THIS

WIRE SHOULD BE TOTALLY UNRAVELED AND TENDED FOR XE THE BEST RECEPTION.

PLAY ING COMPACT DISC

zGETTING START

1. PRESS FUNCTION BUTTON (1 ) 2 TO SELECT “ CD ” MODE.

2 . PRESS “CD TRAY OPEN/CLOSE” BUTTON 3 ( ) TO OPEN THE TRA CD Y ( ).4

3 . PLACE A CD WITH THE PRINTED SIDE FACING UP INSIDE THE TRA Y & THEN CLOSE IT BY CD TRAY

OPEN/CLOSE BUTTON( ). 3

4. FOCUS SEARCH IS PERFORMING, DISPLA THE LCD Y ( )2 WILL SHOW THE TOTAL NUMBER OF TRACKS &

TOTAL PLAY ING TIME.

zPLAY / PAUSE MODE

1. PRESS THE “BAND/ ” BUTTON (17 ) TO START PLAY BACK, THE FIRST TRACK WILL START PLA Y BACK.

2 . TO INTERRUPT, PRESS THE “BAND/ ” 7 BUTTON (1 ) ONCE, AND THE PLAY ING TIME WILL Z BE FREE E &

FLASING ON THE LCD DISPLAY (2). PRESS AGAIN TO RESUME NORMAL PLAY BACK.

zSTOP MODE

1. IF “ STOP ” BUTTON (1 ) IS PRESSED DURING PLA 9 Y OR PAUSE MODE, S WILL YSTEM GO TO STOP

MODE.

zSKIP MODE (SKIP UP / SKIP DOWN )

1. DURING PLA Y OR PAUSE UP MODE, “SKIP IF ” BUTTON (18 ) IS PRESSED. IT WILL X GO TO NE T TRACK

AND DISPLA Y THE TRACK NO. AND THEN REMAIN THE PLAY OR PAUSE MODE.

2 . DURING PLAY OR IF “SKIP PAUSE MODE, DOWN ” 20BUTTON ( ) IS PRESSED. IT WILL GO BACK TO

THE THE BEGINNING OF TRACK, ORIGINAL TRACK NO. IS DISPLAY AND REMAIN THE PLAY OR PAUSE

MODE.

3 . AFTER STEP 2, PRESS “SKIP DOWN ” BUTTON ( ) AGAIN WILL 20 GO TO THE PREVIOUS TRACK AND

REMAIN THE PLAY OR PAUSE MODE.

zFOR 3 MP DISC

1. AFTER FOCUS SEARCH IS PERFORMING, THE TOTAL NUMBER OF TRACK AND ABLUM WILL BE SHOWN

ON THE LCD DISPLA Y (2).

2 4 . PRESS “ FOLDER/ PRE-UP “ (1 ) TO SELECT THE ALBUM NUMBER.

3 . PRESS “ SKIP UP “ OR “ SKIP DOWN “ BUTTON / ) (18 20 TO SELECT THE TRACK NUMBER.

4 . WHEN THE DESIRED TRACK AND ALBUM IS BEING SELECTED, PRESS THE “ BAND/ ” BUTTON (1 7 ) TO

START PLAY BACK.

ID TITLE REMOTE3 (TRACK/ALBUM ) FUNCTION (BY HANDSET)

PRESS “ INFO “ BUTTON UNTIL THE THE LCD DISPLAY ( ) “ -2 SHOW FILE ʳ Ξʳ ϙDURING PLA Y BACK OF

MP3/WMA FILE, THE TITLE SONG / ARTIST NAME / ALBUM NAME IS BEING DISPLAY ED IN SEQUENCE .

PRESS THE “ INFO BUTTON ” AGAIN TO DISABLE THE FUNCTION.

REMARK: -

- IN THAT CASE OF NO NAME HAD BEEN ASSIGNED FOR THE TRACK, “ NO TITLE “ OR “ NO ARTIST “ IS BEING

DISPLAY ED ON” LCD DISPLAY (2).

- NO TITLE/ALBUM NAME CAN BE ED RECOGNIZ IF THE INPUT FORMAT ON THE DISC/MASS MEDIA IS NOT

SUPPORTING BY THE Y S STEM.

- S STEM THE Y SUPPORT ONL Y ENGLISH AND NUMERAL FOR ID3 FUNCTION

E-4

SONG TITLE/FOLDER NAME SEARCH FUNCTION (B REMOTEY HANDSET)

Y OU CAN SEARCH THE TRACK BY THE TITLE/FOLDER NAME DURING PLA IN DISC STOP OR Y BACK MODE:-

1. PRESS THE “ FIND “ BUTTON ONCE, THEN PRESS THE “SKIP UP ” OR SKIP DOWN BUTTON (1 ),8/20

Y OU CAN SEARCH THE TITLE OF EACH SONG ONE BY ONE UNDE R ALPHABET ORDER & THE NUMBER

(A TO Z & THEN 0 TO 9) ORDER ON LCD DISPLAY (2), THEN PRESS THE “ BAND/ ” BUTTON ) (17 TO

START THE PLAY BACK OF THE SELECTED TRACK.

2 . PRESS AGAIN “ FIND ” BUTTON, THE FOLDER BEING NAME IS DISPLAY ED. THEN PRESS THE “SKIP

UP ” OR SKIP DOWN 8 BUTTON (1 /20), TO SELECT THE DESIRED FOLDER, AND PRESS THE

“ BAND/ ” BUTTON ) (15 TO START THE PLAY BACK OF ALL TRACKS INSIDE THAT SELECTED FOLDER.

REMARK: -

MP /WMA3 TRACK FORMAT REQUIREMENT:-

-MP BIT RATE KBPS3 : 32 ~256 KBPS AND WMA BIT RATE KBPS KBPS : 32 ~ 320

- THE PERFORMANCE OF PLAY ING MP3 DISC IS VARIOUS FROM THE QUALIT RECORDING DISCY OF AND

THE METHOD OF RECORDING. FURTHERMORE, THE SEARCHING LEAD-TIME FOR MP -CD IS LONGER 3

THAN NORMAL CD DUE TO DIFFERENCE FORMAT.

zPLAY MODE

PRESS THE PLAY MODE 2 BUTTON ( 1) DURING PLAY BACK TO SELECT REPEAT AND RANDOM FUNCTION, A

SINGLE SINGLE FOLDER ONL TRACK, (MP3 Y ) OR ALL THE TRACKS CAN BE PLA Y ED IN DIFFERENCE MODE

AS FOLLOW:-

FOR CD

(1) REPEAT 1 ( )2 REPEAT ALL 3 TRACK ( ) RANDOM 4 ( ) OFF MODE

INDICATOR

PLAY MODE ON LCD DISPLAY

REPEAT TRACK

REPEAT ALL ALL

RANDOM RAN

OFF -------------- MODE

FOR MP 3/WMA DISC/FILE

(1) REPEAT 1 2 ( ) REPEAT 1 FOLER 3 ( ) REPEAT ALL TRACKS

( ) ( )5 OFF MODE 4 RANDOM

INDICATOR

PLAY MODE ON LCD DISPLAY

REPEAT SINGLE TRACK

REPEAT SINGLE FOLDER

REPEAT ALL TRACKS ALL

RANDOM MODE RAN

OFF MODE -----------------

zREPEAT PLA Y

Y OU CAN LISTEN THE DESIRED TRACKS OR FOLDER REPEATEDLY Y B THIS FUNCTION.

zRANDOM PLAY

Y OU CAN LISTEN ALL THE TRACKS IN A RANDOM ORDER BY THIS FUNCTION

CD / MP 3 DISC PROGRAMMING

UP TO 40 TACKS CAN BE PROGRAMMED FOR DISC PLAY IN AN BEY ORDER. BEFORE USE, SURE TO PRESS

THE “STOP 9 “ BUTTON (1 )

1. SET CD IN MODE STOP & THE PLAY BACK.

2 3 . PRESS THE “MEM/CLK-ADJ” BUTTON (1 ) , “ MEM “ WILL APPEAR ON LCD DISPLAY (2). MOREOVER, IT

WILL INDICATE PROGRAM NO. AND FOR TRACK NO. DIGITS TO BE PROGRAMMED – “ 01 PR 01 “.

E-5

3 . SELECT A DESIRED TRACK BY PRESSING SKIP UP OR DOWN 8 BUTTONS (1 /20).

4 . PRESS THE“ MEM/CLK-AD BUTTON (1 STOREJ ” 3 ) TO THE TRACK INTO MEMOR Y.

5. REPEAT STEPS 3 AND 4 TO ENTER ADDITIONAL TRACKS INTO THE YMEMORY IF NECESSAR .

6 . WHEN ALL THE DESIRED TRACKS HAVE BEEN PROGRAMMED, PRESS BAND/ “” BUTTON ) (17 TO

PLAY THE DISC IN ASSIGNED ORDER.

7 . PRESS “ STOP ” BUTTON 9 (1 ) TO TERMINATE PROGRAM PLA Y.

¾ AFTER PROGRAM COMPLETE, PRESS “MEM/CLK-ADJ” BUTTON 3 (1 ) REPEARTLY TO REVIEW THE

TRACKS BEING PROGRAMMED.

¾ PRESS “ STOP 9 “ BUTTON (1 ) AT CD STOP MODE TO CANCEL ALL YPROGRAMMED MEMOR .

¾FOR MP DISC FILE, PRESS 3 / THE 4 “ FOLDER / PRE-UP “ BUTTON (1 ) TO SELECT THE 1ST TRACK OF

NE FOLDER DIRECTLX T Y AND HENCE SPEED UP TO THE SONG SELECTION.

¾ THE PROGRAMMING MODEL WILL AUTOMATICALLY STOP IF NO BUTTON IS BEING PRESSED IN A

PERIOD OF ABOUT SECONDS 10 AFTER PRESSING THE “ MEM/CLK-ADJ “ BUTTON (13).

PLAY 3BACK OF MP /WMA SONG VIA USB STORAGE MEDIA OR MEMORY CARD

CONNECTING

THE Y S STEM IS ABLE TO DECODE AND PLA Y BACK ALL /WMA MP3 FILE WHICH STORED IN THE MEMORY

MEDIA WITH USB CONNECTING PORT OR SD/MMC MEMORY CARD.

1. SET THE YS STEM AT STANDB MODEY FIRST OR OTHER FUNCTION XE CEPT

SD OR USB MODE.

2 . PLUG-IN THE USB PEN-DRIVE FACE UP WITH THE & MAKE SURE IT GOING

INTO COMPLETELY Y OR INSERT THE MEMOR CARD IN THE DIRECTION OF

THE THE ARROW AS SHOWN IN LABEL ON THE UNDERSIDE OF THE

MEMOR CARD SLOT COVER. INSERT STRAIGHTY WITHOUT BENDING.

zCONNECTING THE USB UPSIDE DOWN OR BACKWARDS COULD DAMAGE

THE AUDIO THE YS STEM OR STORAGE MEDIA (USB THUMB DRIVE /

SD/MMC CARD) . CHECK BE SURE THE DIRECTION IS CORRECT TO

BEFORE CONNECTION.

3 2 . PRESS FUNCTIONS BUTTON (1 ) TO SELECT “ “ SD CARD MODE OR

“ “ USB MODE.

4 Y . THE S STEM WILL START READING THE STORAGE MEDIA AUTOMATICALLY AFTER CONNECTING, AND

LCD DISPLA Y ( )2 WILL SHOW THE TOTAL 3NUMBER OF MP /WMA FILES BEING DETECTED.

5 . REPEAT THE SAME PLA Y BACK PROCEDURE AS PLA Y ING CD/MP3 DISC AS ABOVE.

REMARK

- S THE YSTEM CAN DETECT AND READ THE FILE UNDER MP3 AND WMA FORMAT ONL Y THOUGH THE

USB PORT.

-IF S STEM PLA CONNECT THE Y TO MP3 Y ER VIA THE USB SOCKET, DUE VARIANCES MP TO IN 3

ENCODING FORMAT, SOME 3 MP PLAY ER MAY NOT BE ABLE TO PLAY VIA THE USB SOCKET. THIS IS

NOT A YMAUFUNCTION OF THE S STEM.

-USB PORT DOES SUPPORT E NOT CONNECTION WITH USB XTENSION CABLE AND IS NOT DESIGNED

FOR COMMUNICATION WITH COMPUTER DIRECTL Y

ENCODING OF CD/PHONO 3 INTO MP FILE TO USB MEMORY

THE YS STEM IS ABLE TO ENCODE NORMAL CD OR TURNTABLE MP FORMAT TO 3 AND RECORDING AT

MEMOR MEDIAY WITH USB CONNECTING PORT (OR SM/MMC CARD SLOT). BEFORE STARTING THE

ENCODING, INSERT PLEASE THE MEMORY MEDIA (USB PEN DRIVE OR SD/MMC CARD) TO THE YS STEM &

MAKE SURE IT HAD ADEQUATE FREE MEMOR Y SI E FOR RECRODING:-Z

A) CD ENCODING

I /) ECNODING 1 TRACK 1 DISC

1. PERFORM NORMAL PLAY BACK OF THE CD TRACK OU ENCODE RECORD, Y WANT TO &

2 . PRESS “ 5 “ BUTTON (1 ) DURING THE PLAY BACK OF THE DESIRE TRACK AND THE STEM YS

WILL START ENCODING.

3 Y . THE S STEM WILL SHOW “ ” & “ “ AND FLASHING. ENCODING PERFORMING NOW. IS

4 . PRESS THE “ 5 “ BUTTON (1 ) REPEATLY AGAIN SELECT RECORD TRACK ONE TO 1 “ REC_

“ “ OR RECORD ONE ENTIRE DISC REC_ALL “.

5 . AFTER COMPLETING OF RECRODING, UNIT WILL STOP PLAY BACK AUTOMATICALLY.

II PROGRAM) ENCODING BY

1. PLACE A CD WITH THE PRINTED SIDE FACING UP INSIDE THE TRAY & THEN THE CLOSE CO TRAY.

2 . SELECT THE DESIRE TRACKS B FOLLOWING “ “ Y CD DISC PROGRAMMING PROCEDURES. THEN

PRESS CD PLA “ Y/PAUSE BUTTON “ (17 ) TO START PLAY BACK.

E-6

3 . PRESS THE “ 5 “ BUTTON (1 ) AND THE UNIT WILL DISPLAY “ ” & “ “ AND FLASHING.

ENCODING PERFORMING. IS NOW

4 . PRESS THE “ 5 “ BUTTON (1 ) REPEATLY AGAIN TO SELECT REC ALL “_ “.

5 . AFTER COMPLETED OF ENCODING ACCORDING PRESET PROGRAM, UNIT TO THE WILL STOP

PLAY BACK AUTOMATICALLY.

REMARK -:

- SAME OPERATION PROCEDURE SD/MMC FOR ENCODING TO CARD.

- IF BOTH PEN RECRODING SOURCE (USB DRIVE AND SD/MMC CARD) BEING DETECTED BY THE

SYSTEM DURING ENCODING, “SKIP PLEASE PRESS UP OR DOWN ” 8 BUTTON (1 /20) TO SELECT

THE DESIRE SOURCE. THEN PRESS “ REC (1 “ BUTTON 5 ) AGAIN CONTINUOUS TO THE PROCESS.

- IS THE RECORDING SPEED 1:1 AND ACCORDING TO THE ACTUAL PLY ING TIME OF THE CD TRACK

- S THE YSTEM WILL CREAT A “ AUDIO “ FOLDER AND THEN STORE THE ENCODING TRACK IN IT.

- THE RECORDING FORMAT IS PRESET AT – MP3 BIT RATE KBPS, SAMPLING RATE .1KH : 128 : 44 Z

- NO SONG TITLE WILL BE RECORDED DURING ENCODING MODE

- TO INTERRUPT THE RECRODING, PRESS THE“ STOP 9 “ BUTTON (1 ) DURING RECORDING MODE.

-RECORDING WILL BE COMPLETED ONLY ENTIRE SONG BEING ENCODED, IF TERMINATE THE

ENCODING PROCESS INTERMEDIATEL Y, THERE IS NO TRACK BEING RECORDED NOR STORED TO

THE USB SD/MMC OR CARD

III COP ING OF MP /WMA) Y 3 FILE

IF PUTTING A 3MP /WMA DISC INSTEAD OF A CD-DISC, THE Y S STEM WILL COPY THE FILES TO THE USB OR

SD/MMC CARD THE IF PRESS “ REC BUTTON (1 ). “ 5 THE OPERATION PROCEDURES IS SAME AS CD

ENCODING AS STIPULATE ON ABOVE, AND THE YS STEM WILL Y SWITCH TO COP ING MODE ONLY IF

MP /WMA3 FILE BEING READ.

REMARK:

- S THE YSTEM WILL STORE THE FILE USB SOURCE TO FIRST IF BOTH USB AND SD SLOT ARE BEING

OCCUPLIED STORAGE MEDIA. BY

- S STEM THE Y WILL CREAT A “ FCOPY “ FOLDER AND THEN STORE ALL COPY FILE IN IT.

- IF PRESS THE“ REC (1 DURING PLA “ BUTTON 5 ) Y BACK OF USB OR SD SOURCE, THE FILE WILL COPY

FROM SD OR SD USB. USB TO TO

B) PHONO ENCODING

1) SELECT PHON/AU MODE “X “ AND THEN THE PRESS “ REC (1 DIRECTL “ BUTTON 5 )Y.

2 ) THE LCD DISPLAY ( )2 WITH SHOW “ “ & “ “ AND FLASHING AFTER FEW SECONDS. NOW

THE YS STEM IS STARTING THE ENCODING MODE.

3 ) START PLAY BACK AT PHONO FOR THE TRACK WHICH OU RECORD USB POSITION. Y WANT TO TO

4 ) AFTER FINISH OF RECODING, PRESS THE “STOP 9 “ BUTTON (1 ) UNTIL THE TEXT ON LCD DISPLAY

( )2 STOP FLASHING AND RETURN PHON/AU MODE. TO “X “

C) RADIO ENCODING

1) SELECT TUNER MODE “ “ AND SELECT THEN THE DESIRE RADIO STATION

2 ) PRESS THE“ REC BUTTON (1 START “ 5 ) TO THE ENCODING.

3 ) THE LCD DISPLAY ( )2 WITH SHOW “ “ & “ “ AND FLASHING AFTER FEW SECONDS. NOW

THE YS STEM IS STARTING THE RECORDING.

4 ) AFTER FINISH OF RECODING, PRESS THE “STOP 9“ BUTTON (1 ) UNTIL THE TE XT ON LCD DISPLAY

( )2 STOP FLASHING AND RETURN TUNER MODE. TO “ “

REMARK:-

- IF THE RADIO RECEPTION SIGNAL IS NOT STRONG ENOUGH, THE Y S STEM CANNOT START THE

ENCODING PROCESS AND THE TEX T “ NO GOOD “ WILL SHOW ON THE LCD DISPLAY (2).

- THE RECRODING QUALITY AND PERFORMANCE RADIO ENCODING IS NOT STABLE DUE FOR TO

INTERFERENCE OF RADIO RECEIPTION. THIS IS NOT A MAUFUNCTION OF THE YS STEM.

D) AUX-IN ENCODING

CONNECT ANOTHER AUDIO DEVICE, E.G. (PORTABLE) CD PLA MP PLA ER, CASSETTE YER, 3 Y (PORTABLE)

PLA ER, CORD DIA ACK PLUGS (NOT SUPPLIED).Y IPOD, ETC. STEM YTO THIS S VIA A 5WITH 3. MM J

CONNECT ONE END OF THIS CORD TO THE MM DIA. 3.5 HEADPHONE ACK ON J THE TERNAL DEVICE XE AND

THE TO OTHER END THE 3.5MM AU -IN ON THE SIDE OF THE UNIT. X JACK 5 ( )

WHEN CONNECTED IN WA IT IS POSSIBLE THIS Y TO:

SELECT “PHONO/AU MODE. ONCE X” 3. T5MM PLUG PLUGGED THE AU INX JACK. CHANNEL WILL CHANGE

TO AU IN X AUTOMATICALLY .

• PLA BACK THE MUSIC ALREAD ON THE CONNECTED DEVICE.Y Y

E-7

• ENCODE AND CONVERT THE MUSIC FILES FROM THE CONNECTED DEVICE TO USB/SD INTO MP3

FORMAT. FOLLOW THE SAME PROCEDURE AS DESCRIBED IN THIS MANUAL.

TRACK SEPARATION (BY REMOTE HANDSET)

Y OU CAN DIVIDE THE RECORDING MUSIC FROM PHONO, OR RADIO TO USB/SD TRACK BY TRACK DURING

ENCODING. WHEN EVERY TIME PRESS THE “ “ (TRACK SEPARATION) BUTTON ONCE AT REMOTE

HANDSET DURING TAPE USB/SD, STEM ENCODING PHONO, FROM OR RADIO TO THE YS WILL GENERATE A

NEW TRACK AND CONTINUOUS RECRODING. THE PHONO “, OR TUNER LCD DISPLA THE TEX T “ “ “ AT Y ( )2

WILL FLASHING ONE TIME, IT MEAN THE UNIT IS CREATING A NEW TRACK SUCCESSFULL Y.

ENCODING BITRATE REMOTE HANDSET (BY )

Y OU CAN SELECT THE DESIRED BITRATE DURING ENCODING FROM CD/TAPE/PHONO/RADIO IN AND AUX-1

TO USB OR SELECTABLE RANGE FROM /1 KBPS. SD, THE 32 / / 64 96 28 / 1 / 92 256

1. “ “ ) & SET IN PHON/AUX FUNCTION (12 REMAIN STOP MODE.

2 . PRESS THE “ INFO FUNCTION “ AND THE LCD DISPLA WILL SHOW THE DEFAULT BITRATE (1 KBPS)28

3 . PRESS SKIP OR / ) BUTTONS (18 20 TO SELECT THE DESIRED BITRATE FOR ENCODING.

4 . PRESS AGAIN THE “ INFO “ BUTTON TO CONFIRM THE SETTING AND THE LCD DISPLAY (21) RESUME TO

“ PHON/AU “ MODE X

FILE DELETE AT USB / SD CARD (BY RE MOTE CONTROL)

THE YS STEM IS ABLE TO ERASE STORED THE FILE INSIDE THE USB PEN SD CARD DRIVE OR BY

FOLLOWING:-

A FILE B) SINGLE DELETE ( Y REMOTE HANDSET)

1. PRESET AT “ USB MODE. “ OR SD “ “

2 . PRESS THE “ DELETE “ BUTTON AND LCD DISPLA THE Y ( )2 WILL SHOW (DEL --- 1)00

3 . PRESS SKIP FORWARD OR SKIP BACKWARD BUTTON SELECT TO THE FILE GOING TO DELETE.

4 . PRESS THE “ DELETE “ BUTTON TO ENTER “ YES / NO “ MODE AND THEN PRESS SKIP FORWARD

OR SKIP BACKWARD TO SELECT “ YES “ OR “ NO “.

5 . PRESS THE “ DELETE “ BUTTON AGAIN SETTING. TO CONFIRM THE

REMARK :

- “ PRESS STOP “ BUTTON ONCE AT REMOTE HANDSET QUITE DELETE TO MODE

REMOVING OF USB / MEMORY CARD

TO REMOVE THE USB / MEMORY CARD, TURN OFF THE POWER OR SWITCH THE FUNCTION MODE TO

EITHER CD, PHONO OR TUNER FIRST. FOR USB PORT – UN-PLUG IT PULLING OUT BY THE USB SOCKET

DIRECTLY, FOR MEMORY CARD – PULLING OUT THE SD CARD SMOOTHLY.

PHONO

OPERATION

- REMOVE THE STYLUS PROTECTOR.

- BE SURE THAT THE TONE ARM IS BEING DETACHED FROM THE TONE ARM

REST BEFORE OPERATING AND RE-SECURED AGAIN AFTERWARDS.

1. PRESS FUNCTION BUTTON 2 (1 ) TO SELECT “ PHONO/AUX ” MODE.

THE LCD DISPLA Y ( ) “2 WILL SHOW PHONO/AUX “.

2 . SET THE SPEED SELECTOR (32) TO THE THE PROPER POSITION DEPENDING ON RECORD BE TO

PLAY ED.

3 . PLACE THE RECORD ON THE PLATTER (USE THE SPINDLE ADAPTOR IF REQUIRED).

4 . SET THE CUEING LEVER (30) TO THE UP POSITION.

5 . LIFT THE TONE ARM FROM THE REST AND SLOWL Y MOVE IT TO THE RECORD SIDE. THE PLATTER WILL

START TO ROTATE AND LOCATE THE TONE ARM OVER THE DESIRED POSITION OF THE RECORD.

6 . PULL DOWN THE CUEING LEVER (30). THE TONE ARM WILL COME SLOWLY ON THE RECORDER AND

START PLAY BACK.

7 . AT THE END OF RECORD, THE TONE ARM WILL RETURN TO THE REST POSITON AUTOMATICALLY.

8 . TO STOP MANUALLY, LIFT THE TONE ARM FROM THE RECORD AND RETURN IT TO THE REST.

REMARK DUE DEVICE : TO THIS DESIGNED PHONO AND AUX IN THE SAME CHANNEL. WHEN AUX JACK

WAS PLUGGED 5 BY 3. MM PLUG, THE CHANNEL WILL SWITCH TO AUX F UNCTION AUTOMATICALLY.

PLEASE . MM PLUG DURING PLA REMOVE THE 3 5 FROM THE AUX JACK(5) Y THE PHONO.

zPLAY SUSPENSION

SET THE THE CUEING LEVER (30) TO UP POSITION WILL LIFE UP THE TONE ARM AND THEN STOP

PLYABACK TEMPOARILY

E-8

zPLAY EJECTION

PRESS ECT BUTTON (1 AN TIME DURING THE JE 6 )Y PLAY BACK WILL RETURN THE TONE ARM TO THE REST

POSITION IMMEDIATELY.

Remark :

- DUE RECORD TO THE LENGTH OF THE IS VARIOUS, IF YOU FIND THE TONE ARM CANNOT

RETURN AUTOMATICALLY AFTER PLAY J BACK OF RECORD. PLEASE PRESS THE E ECT

BUTTON AND RETURN THE TONE ARM BACK TO THE POSITION REST

- A USERS SHOULD NOT CHANGE TO MAGNETIC CARDRIDGE S Y STEM, OTHERWISE UNIT

CAN´ T BE CONNECTED ANYMORE TO AN AU X-IN OF MUSIC-CENTER

ADJUSTMENTS

ANTI-SKATING CONTROL

- SET THE ANTI-SKATING CONTROL (29) TO THE POSITION WHICH CORRESPONDING THE TO ADJUSTED

ST LUS WORKING PRESSURE. IFY THE WORKING PRESSURE IS 2 GRAMS, THE ANTI-SKATING

CONTROL ALSO TO BE SET AT 2.

PLATTER SPEED ALIGNMENT

- DURING PLAY BACK OF RECORD, OBSERVE THE APPROPIATE STRIP OF STOBE CALIBRATION DOTS

FROM THE THE STROBE LENS. UPPER ONE IS FOR RPM 33 AND THE MIDDLE ONE IS FOR RPM. 45

- IF THE STROBE DOTS APPEAR FLOWING TO TO THE RIGHT, MEANS IT THE PLATTER IS REVOLVING

SLOWER THEN RATED SPEED. TURN THE PITCH CONTROL (33) TO THE “ + “ DIRECTION. IF THE

STROBE DOTS APPEAR FLOWING TO TO THE LEFT, IT MEANS THE PLATTER IS REVOLVING FASTER

THAN RATED SPEED. TURN CONTROL THE PITCH (33) TO THE “ – “ DIRECTION.

- J AD UST THE PITCH CONTROL (33) UNTIL THE STROBE DOTS DO APPEAR BE STATIONAR TO Y WITHOUT

MOVING OR RIGHT. LEFT

TONE ARM STOPPING POSITION ALIGNMENT

- THE POSITION OF THE TONE ARM COMPLETE PLA Y BACK AND RETURN TO THE REST STATION CAN BE

AD USTEDJ AT THE ALIGNMENT SCREW (27) AS FOLLOW:-

- BEFORE STARTING THE ALIGNMENT, TAKE PLEASE OUT THE HOLE COVERING RUBBER:-

A) IF STEM COMPLETE PLA THE YS CANNOT THE YBACK OF RECORD RETURN AND EARLIER

1) USE A CROSS HEAD SCREW DRIVER AND TURNING THE ALIGNMENT SCREW INSIDE (34) THE HOLE

CLOCKWISE, THE STOPPING AND E ECT OF J POSITION THE TONE ARM WILL MOVE MORE INWARD TO THE

CENTER OF THE RECORD BEFORE PLA Y BACK COMPLETION.

B S STEM) IF THE Y CANNOT RETURN TO REST POSITION AUTOMATICALL Y AFTER PLAYBACK OF RECORD

2 ) USE A CROSS HEAD SCREW DRIVER AND TURNING THE ALIGNMENT SCREW INSIDE (34) THE HOLE

ANTI-CLOCKWISE, THE STOPPING AND EJECT POSITION OF THE TONE ARM WILL MOVE MORE AWA Y FROM

THE CENTER OF THE RECORD BEFORE PLA Y BACK COMPLETION.

REMARK: -

- THE STOPPING POSITION IS VERY SUBJ ECTIVE AMONG DIFFERENCE CUSTOMERS, PLEASE SELECT

THE MOST SUITABLE POSITION BASED ON OUR OWN RECORD COLLECTION. Y THE XE -FACTORY

SETTING IS BASED ON THE MOST COMMON TEMPLATE.

- PLEASE CHECK THE STOPPING POSITION TIME TIME BY DURING AD AND AVOID OVER JUSTMENT

TURNING OF THE SCREW INSIDE.

Produkt Specifikationer

Mærke:	Soundmaster
Kategori:	Pladespiller
Model:	PL875USB

Har du brug for hjælp?

Hvis du har brug for hjælp til Soundmaster PL875USB stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Pladespiller Soundmaster Manualer

Soundmaster SF510 Manual

27 September 2024

Soundmaster PL186H Manual

31 August 2024

Soundmaster PL905 Manual

22 August 2024

Soundmaster PL875USBV2 Manual

5 August 2024

Soundmaster PL979 Manual

1 August 2024

Soundmaster NR545DAB Manual

27 Juli 2024

Soundmaster PL-520USB Manual

27 Juli 2024

Soundmaster PL875USB Manual

26 Juli 2024

Soundmaster PL590 Manual

20 Juli 2024

Soundmaster PL 186 Manual

19 Juli 2024

Pladespiller Manualer

Nyeste Pladespiller Manualer

House Of Marley Revolution Pack Manual

3 Marts 2025

Elipson Chroma 200 Manual

3 Marts 2025

Roadstar RCR-777UD+ Manual

24 Februar 2025

Roadstar TTR-1923UCEN Manual

24 Februar 2025

Tone Factory Turntable Manual

23 Februar 2025

Sumiko Pearl Manual

21 Februar 2025

Sumiko Black Pearl Manual

21 Februar 2025

Pro-Ject Debut PRO S Balanced Manual

19 Februar 2025

Pro-Ject Metallica Limited Edition Manual

19 Februar 2025

Victrola VTA-75 Manual

9 Februar 2025