StarTech.com PEX10GSFP Manual


Læs nedenfor 📖 manual på dansk for StarTech.com PEX10GSFP (2 sider) i kategorien Netværkskort/adapter. Denne guide var nyttig for 11 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Manual Revision: March 10, 2022 11:40 AM
Product Diagram (PEX10GSFP)
Component Function
1SFP+ Slot Connect a 10G SFP+ Transceiver Module to the
PCI Express Card.
2Link/Activity LED
Solid Green: Network Device A link to a has
been established.
Flashing Green: Indicates network activity.
3PCI Express Connector
(x4)
Used to connect the to the PCI Express Card
Host Computer.
Gen 3 connection.
Package Contents
Network Card x 1
Low-Prole Bracket x 1
Quick-Start Guide x 1
Requirements
For the latest requirements, please visit www.startech.com/PEX10GSFP
PCI Express enabled computer with an available PCI Express p1-x4 slot
10G SFP+ Transceiver Module
1 Port PCI Express 10GbE SFP+ Network Adapter Card
Hardware Installation
Installing the Low Prole Bracket
By default the is attached to the . Depending Full Prole Bracket PCI Express Card
on your system conguration you may need to remove the and Full Prole Bracket
replace it with the (included).Low Prole Bracket
1. Using a , remove the two securing Small Phillips Head Screwdriver Bracket Screws
the to the .Full Prole Bracket PCI Express Card
2. Align the on the with the on theScrew Holes PCI Express Card Screw Holes Low
Prole Bracket PCI Express Card Screw . Making sure the is sitting on-top of the
Holes Low Prole Bracket on the .
3. Insert the through the and into the Bracket Screws PCI Express Card Screw Holes
on the . Low Prole Bracket
4. Using the , tighten the , being Small Phillips Head Screwdriver Bracket Screws
careful not to over-tighten.
Installing the PCI Express Card
Static Electricity PCI Express Cardscan severely damage . Ensure that you are
adequately before you open your or touch the Grounded Computer Case PCI
Express Card Anti-Static Strap Anti-Static Mat . You should wear an or use an when
installing any computer component. If an isn’t available, discharge Anti-Static Strap
any built-up static electricity by touching a large for several Grounded Metal Surface
seconds. Only handle the by its edges and don’t touch the gold PCI Express Card
connectors.
1. Turn o the and any connected to the Host Computer Peripherals Devices
computer (e.g. printers, external hard drives, etc.).
2. Unplug the from on the back of the and disconnect all Power Cable Host Computer
Peripheral Devices.
3. Remove the from the (refer to the documentation that Cover Host Computer Case
came with the for further details).Host Computer
4. Locate an open and remove the metal cover plate on the rear of PCI Express p1-x4 Slot
the (See documentation for your computer system for details).Computer Case
Note: This card will work in of additional lanes (e.g. x8, or x16 PCI Express Slots
slots).
5. Gently insert the into an open and fasten the PCI Express Card PCI Express Slot
Bracket Computer Case to the rear of the .
6. Place the back onto the .Cover Computer Case
1
2
3


Produkt Specifikationer

Mærke: StarTech.com
Kategori: Netværkskort/adapter
Model: PEX10GSFP

Har du brug for hjælp?

Hvis du har brug for hjælp til StarTech.com PEX10GSFP stil et spørgsmål nedenfor, og andre brugere vil svare dig




Netværkskort/adapter StarTech.com Manualer

Netværkskort/adapter Manualer

Nyeste Netværkskort/adapter Manualer

LevelOne

LevelOne FNC-0109TX Manual

14 Oktober 2024
Legrand

Legrand CS102 Manual

9 Oktober 2024
Edimax

Edimax EW-7822ULC Manual

8 Oktober 2024
Alecto

Alecto HPD-142 Manual

4 Oktober 2024
LevelOne

LevelOne GNC-0122 Manual

4 Oktober 2024
TP-Link

TP-Link UE200 Manual

3 Oktober 2024
Tenda

Tenda W311MA Manual

2 Oktober 2024
NEC

NEC NP05LM4 Manual

30 September 2024