Sun Joe 24V-HCSWP-CT Manual

Sun Joe savemaskine 24V-HCSWP-CT

Læs nedenfor 📖 manual på dansk for Sun Joe 24V-HCSWP-CT (76 sider) i kategorien savemaskine. Denne guide var nyttig for 5 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/76
Original instructions.
© 2022 Snow Joe, LLC. All rights reserved.
1
A Division of Snow Joe, LLC Model 24V-HCSWP-CT Form No. SJ-24V-HCSWP-CT-880E-M
R
OPERATOR’S MANUAL
CORDLESS TELESCOPING
POLE + PRUNING SAW TOOL ONLY
24V MAX* | 250W | 5" BAR + CHAIN LENGTH
EN
*Initial no-load voltage, when fully charged, peaks at 24 volts;
nominal voltage under typical load is 21.6 volts.
SAVE THESE INSTRUCTIONS
IMPORTANT!
Safety Instructions
All Operators Must Read These
Instructions Before Use
Always follow these safety guidelines. Failure to do so may
result in serious bodily injury or death.
General Safety
mWARNING! This appliance is not intended for use
by children or by unassisted, unsupervised persons whose
physical, sensory or mental capabilities prevent them from
using it safely. Children should be supervised to ensure that
they do not play with the appliance.
Before starting up your machine, please check it carefully for
any defects. If you nd any, do not start up your machine.
Contact your authorized Snow Joe® + Sun Joe® dealer or
call the Snow Joe® + Sun Joe® customer service center at
1-866-SNOWJOE (1-866-766-9563).
mWARNING! When using the power tool, basic safety
precautions should always be followed to reduce the risk of
re, electric shock, and personal injury. These include:
1. Keep work area clean and well-litCluttered, dark
areas invite accidents. Always inspect the area where the
pole + pruning saw is to be used.
2. Avoid dangerous environments – Do not use the power
tool in rain, in damp or wet locations, or in bad weather,
especially when there is a risk of lighting. This decreases
the risk of being struck by lighting. Do not operate the
power tool in gaseous or explosive atmospheres or use
the power tool near ammable or combustible liquids.
Motors in these tools may spark, and the sparks might
ignite fumes.
3. Know your product – Know how to start and stop the
machine. Be thoroughly familiar with the controls.
4. Keep children, bystanders, and pets away –
All spectators, including pets, should be kept a safe
distance away from the work area.
5. Dress properly – Do not wear loose clothing or jewelry.
They can get caught in moving parts. Protective rubber
gloves and non-slip footwear are recommended when
working outdoors.
6. Avoid Slipping – Exercise caution to avoid slipping or
falling. Wear protective footwear that will protect your feet
and improve your footing on slippery surfaces.
7. Stay alert Watch what you are doing. Use common
sense. Do not operate the power tool when you are tired,
or under the inuence of alcohol or drugs.
8. Do not overreach Keep proper footing and balance at
xall times.
9. Prevent unintentional starting – Do not pull the trigger
before connecting to battery pack, picking up or carrying
the appliance. Do not carry the pole + pruning saw with
your nger on the trigger.
10.
Use the right appliance – Do not use the power tool for
any applications other than those for which it was intended.
11. The chain is sharp – Don't grasp the exposed chain or
cutting edges when picking up or holding the power tool.
12. Use two hands – Hold the telescoping pole and handle
with both hands to avoid loss of control.
13. Remove the battery – Remove the battery from the
power tool when it is not in use, before servicing it, when
changing accessories, and when performing any other
maintenance task.
14.
Use safety glasses – Also use safety footwear, snug-tting
clothing, protective gloves, hearing and head protection.
15. Use head protection – Always use head protection when
operating the power tool overhead. Falling debris can
result in serious personal injury.
16. Do not force the tool – It will perform better with less
likelihood of personal or mechanical injury if it is used at
the rate for which it was designed.
17. Check for damaged parts – Before further use of the
appliance, all guards and parts should be carefully
checked to determine that it will operate properly and
perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts,
mounting, and any other condition that may aect its
operation. A guard or other part that is damaged should
be properly repaired or replaced. Contact the Snow Joe®
+ Sun Joe® customer service center at 1-866-SNOWJOE
(1-866-766-9563) for assistance.
18. Maintain the power tool with care – Keep the cutting
edges sharp and clean for optimal performance and to
reduce the risk of injury. Keep the handles dry, clean,
and free from oil and grease. Follow the additional
recommendations described in the maintenance section
of this manual.


Produkt Specifikationer

Mærke: Sun Joe
Kategori: savemaskine
Model: 24V-HCSWP-CT

Har du brug for hjælp?

Hvis du har brug for hjælp til Sun Joe 24V-HCSWP-CT stil et spørgsmål nedenfor, og andre brugere vil svare dig




savemaskine Sun Joe Manualer

savemaskine Manualer

Nyeste savemaskine Manualer

Einhell

Einhell GE-CS 18 Li Manual

15 Oktober 2024
MSW

MSW -TAS287 Manual

15 Oktober 2024
MSW

MSW T-SAW300 Manual

15 Oktober 2024
Makita

Makita 5603 Manual

14 Oktober 2024
FERM

FERM FKS-165 Manual

13 Oktober 2024
Einhell

Einhell TC-AP 650 E Manual

12 Oktober 2024
Einhell

Einhell BT-SM 2534 Manual

11 Oktober 2024
Hitachi

Hitachi C 7MFA(LA) Manual

9 Oktober 2024
Ozito

Ozito ECS-406A Manual

6 Oktober 2024