Supermicro X10SLE-F Manual

Supermicro Ikke kategoriseret X10SLE-F

Læs nedenfor 📖 manual på dansk for Supermicro X10SLE-F (1 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 5 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/1

SUPERMICR R

ContaCt nformatIon I

MNL-1486-QRG R . 1.00ev

• www.supermicro.com(Email:support@supermicro.com)

• Manuals:http://www.supermicro.com/support/manuals

• Drivers&Utilities:ftp://ftp.supermicro.com

• Safety:http://www.supermicro.com/about/policies/safety_information.cfm

consent. All Trademarks are property of their respective entities. All information provided is deemed accurate at the time of printing; however, it is not guaranteed.

P C - BaCkage ontents ulk

X10sle-f/Hf

Q r g uICk eferenCe uIde r . 1.00ev

• One(1)QuickReferenceGuide

LED Indicators

Connectors

DIMM Memory Installation

Jumpers, Connectors and LED Indicators Memory Support

Motherboard Layout and Features

Jumpers

Note: Graphics shown in this quick reference guide are for illustration only. Your components may or may not look exactly the same as drawings shown in this guide. Note: Refer to Chapter 1 of the User Manual for detailed information on jumpers, connectors,

and LED indicators.

Note: Refer to Chapter 2 of the User Manual for detailed information on memory support and CPU/

motherboard installation instructions.

= mounting hole

I-SATA4

JSD1JTPM1

JBR1

JPV1

JWD1

JPB1

JPME2

JPME1

J19

JPG1

J18

J22

JBT1

SW1

LED5

LED6

JKVM1

JUIDB1

JPWR2

I-SATA1I-SATA0 I-SATA3I-SATA2

JP16

JP1

JP18JP17

BAR CODE

MAC CODE

Battery

USB3.0-0

IPMI_LAN

UID

MICRO-L PCI-E 3.0 X8P

X10SLE-F/HF

Rev. 1.00

PWR

DIMMB2

DIMMB1

DIMMA2

DIMMA1

CPU

BIOS

PCH

BMC

AST2400

Intel LP

C226/C224

Jumper Description Default

JBT1 CMOS Clear (See Chpt. 2)

JPG1 VGA Enable Pins 1-2 (Enabled)

JPME1 ME Recovery Pins 1-2 (Normal)

JPME2 Manufacture Mode Select Pins 1-2 (Normal)

JWD1 Watch Dog Timer Enable Pins 1-2 (RST)

Connector Description

Battery Onboard Battery

IPMI_LAN IPMI_Dedicated LAN

JKVM1 USB (x2)/VGA (Monitor)/COM (UART) Connector for Remote Console

Redirection or Remote Network Interface

JP16 Power Output for Hard Disk Drive (12V and 5V)

JP17 Motherboard Interface to PDB

JP18 Motherboard Interface to PDB

JPWR2 SMC-Proprietary Power Connector

JSD1 SATA DOM (Device_On_Module) Power Connector

JTPM1 Trusted Platform Module/Port 80 Connector

I-SATA0 - I-SATA4 (Intel PCH) Serial ATA Ports 0-4 (I-SATA0-3: SATA 3.0 Ports, I-SATA4:

SATA 2.0 Port)

Micro-LP PCI-E Slot SMC-Proprietary Micro Low-Prole (LP) PCI-Express 3.0 x8 Slot

SW1 Power Switch/LED Indicator

UID Unit Identier (UID) Button (JUIDB)

USB2, USB3 (3.0) Internal Type A USB 3.0

The X10SLE-F/-HF supports up to 32GB of Unbuffered (UDIMM) DDR3 ECC

1600/1333/1066 MHz VLP (Very Low Prole) memory in 4 slots.

Memory Population Guidelines

Please follow the table below when populating the X10SLE-F/HF.

Recommended Population (Balanced)

DIMMA2 DIMMB2 DIMMA1 DIMMB1 Total System Memory

2GB DIMM 2GB DIMM 4GB

2GB DIMM 2GB DIMM 2GB DIMM 2GB DIMM 8GB

4GB DIMM 4GB DIMM 8GB

4GB DIMM 4GB DIMM 4GB DIMM 4GB DIMM 16GB

8GB DIMM 8GB DIMM 16GB

8GB DIMM 8GB DIMM 8GB DIMM 8GB DIMM 32GB

Insert the desired number of DIMMs into the memory slots, starting with DIMMA2

(Channel A, Slot 2). For the system to work properly, please use the memory

modules of the same type and speed in the same motherboard.

Channel A Slot 1

Channel A Slot 2

(Blue Slot)

Channel B Slot 1

Channel B Slot 2

(Blue Slot)

Towards the CPU

Notches

Release Tabs

Press both notches

straight down into

the memory slot.

Link ivi LED Act ty LED

IPMI LAN

IPMI LAN Link LED (Left) &

Activity LED (Right)

Color/State Denition

Link (Left) Green: Solid 100 Mbps

Amber: Solid 1000 Mbps

Activity (Right) Yellow Blinking Active

Tools Needed:

Screwdriver

Phillips screws (9)

CPU Installation

CPU Properly

Installed

Load Lever Locked

into Place

Load Lever

Load Plate

Pin 1

North Center Edge

Heatsink Installation

Screw#1 Screw#2

Screw#3

Screw#4

Motherboard

Mounting Holes

Heatsink Bracket

IPMI LAN Port LED

LED Description Color/State Status

LE5 BMC Heartbeat LED Green: Blinking BMC Functions Normally

LED5 Power Fail/Fan Fail/Overheat Red: On Power Fail, Fan Fail or Overheating

LED6 UID LED Blue: On Unit Identied

Produkt Specifikationer

Mærke:	Supermicro
Kategori:	Ikke kategoriseret
Model:	X10SLE-F
Bredde:	117 mm
Dybde:	297 mm
Wi-Fi:	Ingen
Opbevaringstemperatur (T-T):	-40 - 70 °C
Relativ luftfugtighed ved drift (H-H):	8 - 90 %
Relativ luftfugtighed ved opbevaring (H-H):	5 - 95 %
Antal USB 3.2 Gen 1 (3.1 Gen 1) type-A-porte:	1
Ethernet LAN:	Ja
Driftstemperatur (T-T):	0 - 50 °C
Maksimal intern hukommelse:	32 GB
On-board grafikkort, model:	Aspeed AST2400
Processorproducent:	Intel
Komponent til:	Server
Processor sokkel:	LGA 1150 (stik H3)
Understøtter RAID:	Ja
Fejlkorrigerende kode:	Ja
Understøttelse af parallel behandlingsteknologi:	Ikke understøttet
Kompatibel processor serie:	Intel® Pentium®
Bundkort chipsæt:	Intel® C224
Understøttede hukommelsestyper:	DDR3-SDRAM
Understøttede hukommelsesclock-hastigheder:	1600 MHz
Antal SATA III-stik:	4
LAN Kontroller:	Realtek RTL8211E
USB 3.2 Gen 1 (3.1 Gen 1) stik:	2
Indbrudsttik til kabinet:	Ja
Antal kabinetventilatorstik:	5
Understøttede lagerdrev brugerflader:	SATA III
BIOS-type:	AMI
ACPI-version:	5.0
RAID-niveauer:	0, 1,5, 10
Antal understøttede processorer:	1
Hukommelsesspænding:	1.5 V
TPM-stik:	Ja
Antal DIMM-slots:	4
PCI Ekspres x8 (Gen 3.x) slots:	1
IPMI LAN (RJ-45) port:	Ja
Understøttet DIMM modul kapaciteter:	1GB, 2GB, 4GB, 8GB
Intel® Xeon serie:	E3-1200
Maksimal UDIMM hukommelse:	32 GB