Tacklife SC-L01 Manual
Tacklife
Laser pointer
SC-L01
Læs nedenfor 📖 manual på dansk for Tacklife SC-L01 (2 sider) i kategorien Laser pointer. Denne guide var nyttig for 10 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/2
- EN - - EN - - EN - - EN - - EN - - EN - - EN - - EN - - EN -
Shenzhen Temie Technology Co. Ltd.
Web:www.tacklife.net
E-mail:support@tacklife.net
ADD:No.31, Qing Linxi Road, Longgang
District,Shenzhen, Guangdong, China 518172 CN
Mini Cross Line Laser
Model: SC-L01
User Manual
Contents
Congratulations!
You have chosen one of our laser tools that’s guaranteed reliable and
tough for professional tool users at various job sites.
• Safety
• Product Overview
• Operation Modes
• Applications
• User Guide, Maintenance and Care
• Specifications
• Warranty
Product Overview
1. Laser Windows
2. Power/Lock
3. Battery Compartment
4. 1/4-20 Mounting Thread
1
2
Safety
WARNING:
Read the Safety Instructions and User Manual thoroughly before using this
product. All users must fully understand and adhere to these instructions.
CAUTION:
While the product is in operation, be careful not to expose your eyes to the
emitting laser beam (red or green light source). Exposure to a laser beam
for an extended time may be hazardous to your eyes.
CAUTION:
Glasses may be supplied in some of the laser tool kits. These are NOT
certified safety glasses. These glasses are ONLY used to enhance visibility of
beam in brighter environments or at greater distances from laser source.
WARNING:
The following label/print samples are placed on the product to inform of
the laser class for your convenience and safety.
• Do not stare directly into the beam or view directly with optical instruments
or set up the laser at eye level.
• Do not disassemble the laser tool. There are no user serviceable parts inside.
• Do not modify the laser in any way. Modifying the tool may result in
hazardous Laser Radiation Exposure.
• Do not operate the laser around children or allow children to operate
the laser. Serious eye injury may result.
• An exposure to the beam of a Class 2 laser is considered safe for a
maximum of 0.25 seconds. Eyelid reflexes will normally provide adequate
protection.
Applications
User Guide, Maintenance and Care
• The laser tool is sealed and calibrated at the plant to the accuracies
specified.
• It’s recommended to carry out an accuracy check before its first use
and periodic checks during future use especially for precise layouts.
• When not in use please power OFF the tool and place the pendulum
lock in its locked position.
• In Manual Mode, self leveling is OFF. The accuracy of the beam is not
ensured to be level.
• Do not short any battery terminals or charge alkaline batteries or dispose
of batteries in fire.
• Do not mix old and new batteries. Replace all of them at the same time
with new batteries of the same brand and type.
• Keep batteries out of reach of children.
• Remove batteries if the tool will not be used for several months.
• Do not store the laser tool in direct sunlight or expose it to high temperatures.
The housing and some internal parts are made of plastics and may
become deformed at high temperatures.
• Exterior plastic parts may be cleaned with a damp cloth. Although
these parts are solvent resistant, NEVER use solvents. Use a soft, dry cloth
to remove moisture from the tool before storage.
• Store the tool in its case when not in use. If storing for extended time,
remove batteries before storage to prevent possible damage.
3
4
Warranty
We are confident of the quality of our products and offer outstanding
guarantee for professional users of the products. This statement is in addition
to and in no way prejudices your contractual rights as a professional user
Laser Class
Laser Wavelength
Leveling Accuracy
Horizontal/Vertical Accuracy
Leveling/Compensation Range
Working Distance (Line)
Working Distance
(Line with Detector)
Power Source
IP Rating
Operation Temperature Range
Storage Temperature Range
Class 2 (IEC/EN60825-1/2007)
635±5nm
±4.5mm/15m
±4.5mm/15m
4°±1°
15m
approximately 12Hours
( )10 mw diode used to split beams
2×˝AA˝ (LR6)
IP54
-10 – 50℃ ＋ ℃
-20 – 70℃ ＋ ℃
or your statutory rights as a private non-professional user. We warrant our
laser level(s) against faults in materials and/or workmanship for one year
from date of purchase provided that:
• Proof of purchase is produced.
• Service/repairs have not been attempted by unauthorized persons;
• The product has been subject to fair wear and tear;
• The product has not been misused;
Defective products will be repaired or replaced, free of charge or at our
discretion, if sent together with proof of purchase to our authorized
distributor(s).
This Warranty does not cover faults caused by accidental damage, unfair
wear and tear, and use other than in accordance with the manufacturers’
instructions or repair or alteration of this product not authorized by us.
Repair or replacement under this Warranty does not affect the expiry date
of the Warranty.
To the extent permitted by law, we shall not be liable under this Warranty
for indirect or consequential loss resulting from faults in this product. This
Warranty may not be varied without our authorization. Calibration and
care are not covered by warranty.
NOTE:
The customer is responsible for the correct use and care of the tool. Moreover,
the customer is completely responsible for periodically checking the
accuracy of the laser, and therefore for the calibration of the tool
35m
Operating Time
Operation Modes
• Do not dispose of this product with household waste.
• Always dispose of batteries per local code.
• Please recycle in line with local provisions for the collection and disposal
of electrical and electronic waste under the WEEE Directive.
Specifications – Red Beams
1. Unlock the laser tool by switching to the Unlocked Position to turn the
laser tool ON and project the cross line.
2. Lock the laser tool by switching to the Locked Position to turn the laser
tool OFF and shut off the cross line.
3. Short press the key on the keypad while the laser tool is powered On in
the Unlocked Position to deactivate or activate out-of-self-leveling alert.
4. Laser beams will flash once every 5 seconds when out of self-leveling
range alert in the Unlocked Position is deactivated.
5. Laser beams will flash twice a second when the laser tool is out of its
self leveling range in the Unlocked Position with its self-leveling range
alert activated.
Produkt Specifikationer
| Mærke: | Tacklife |
| Kategori: | Laser pointer |
| Model: | SC-L01 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Tacklife SC-L01 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Laser pointer Tacklife Manualer
22 August 2024
Laser pointer Manualer
- Laser pointer Bosch
- Laser pointer SilverCrest
- Laser pointer Metabo
- Laser pointer DeWalt
- Laser pointer RYOBI
- Laser pointer Skil
- Laser pointer ADA
- Laser pointer Makita
- Laser pointer Bushnell
- Laser pointer Nikon
- Laser pointer Da-Lite
- Laser pointer Hama
- Laser pointer Milwaukee
- Laser pointer Laserliner
- Laser pointer Parkside
- Laser pointer Black And Decker
- Laser pointer Einhell
- Laser pointer Leica
- Laser pointer Stanley
- Laser pointer Hilti
- Laser pointer United Office
- Laser pointer Melinera
- Laser pointer Powerplus
- Laser pointer BeamZ
- Laser pointer Stairville
- Laser pointer Velleman
- Laser pointer Carson
- Laser pointer Stabila
- Laser pointer Vortex
- Laser pointer Connect IT
- Laser pointer GPO
- Laser pointer Eurolite
- Laser pointer Uni-T
- Laser pointer Toolcraft
- Laser pointer Cameo
- Laser pointer Steren
- Laser pointer Kaiser
- Laser pointer Cocraft
- Laser pointer Klip Xtreme
- Laser pointer Kensington
- Laser pointer Laserworld
- Laser pointer Kreator
- Laser pointer Perfect Choice
- Laser pointer Prexiso
- Laser pointer Picotronic
- Laser pointer Meopta
Nyeste Laser pointer Manualer
6 December 2024
16 November 2024
3 Oktober 2024
23 September 2024
21 September 2024
14 September 2024
13 September 2024
13 September 2024
11 September 2024
8 September 2024