Tannoy Platinum B6 Manual

Tannoy Højttaler Platinum B6

Læs nedenfor 📖 manual på dansk for Tannoy Platinum B6 (2 sider) i kategorien Højttaler. Denne guide var nyttig for 8 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
SELECT
PLATINUM F6/B6
2-Way Bookshelf and 3-Way Floorstanding
6.5" HiFi Loudspeakers
Introduction
Thank you for selecting Tannoy loudspeakers,
developed in the UK by our dedicated team
of design engineers. These speakers are the
choice of discriminating music lovers the world
over. Musical excellence is designed into our
loudspeakers from the start. Careful selection of the
very best components combined with strict quality
control procedures in the production process
ensures this level of excellence is maintained.
To gain maximum performance from your
loudspeakers, please take time to read this
document in full before installation.
Loudspeakers are electromechanical devices that
‘run-in’ through use; performance will therefore
improve after an initial period of 24 hours use.
Once they have been further run-in over a longer
period, there will be clear enhancement of the
stereo imaging, mid-band quality and bass
performance characteristics.
We are condent that you will continue to enjoy
your new Tannoy loudspeakers for many years
to come.
Amplier Choice
Consult the product specication page as this
clearly shows the acceptable power range for
amplier matching to your speakers. The high peak
power handling of Tannoy loudspeakers permits
responsible use with more powerful ampliers.
As with all loudspeaker systems, the power
handling is a function of voice coil thermal
capacity. Care should be taken to avoid overdriving
any amplier, as this will cause output overload
resulting in ‘clipping’ or distortion within the
output signal. This will cause damage to the
speakers if done for any extended period.
Generally, an amplier of higher power that is
running hard, but free of distortion, will do less
damage to the loudspeaker than a lower power
amplier continually clipping. Remember also that
a high-powered amplier running at less than
90% of output power generally sounds a great deal
better than a lower powered example struggling to
achieve 100%. An amplier with insucient drive
capability will not allow the full performance of the
loudspeakers to be realised.
Unpacking
To unpack the loudspeakers from their boxes
remove tape from the top then fold the aps right
back before inverting the carton and contents.
Lift the carton clear of the contents then remove
all inner packaging. It is strongly recommended
that you store all the packaging to allow protected
transportation in future.
Installation
The F6 oorstanding model comes with rubber
feet to minimize resonance and coloration.
Ensure that the speaker is placed on level ground
to prevent tipping.
The B6 bookshelf speakers should be located
securely on stands or a shelf in an appropriate
position to place the high frequency unit roughly
at ear height when seated in the chosen listening
position. Positioning recommendations for
stand-mounted speakers can be found under the
section entitled Positioning and Fine Tuning.
Connection
The positive (plus) terminal on the amplier
left channel (marked + or coloured red) must
be connected to the positive HF terminal on
the left speaker. The left speaker is the one on
the left as you look at the stereo pair from your
listening position.
The negative (minus) terminal on the amplier
left channel (marked - or coloured black) must
be connected to the negative HF terminal on the
left speaker.
Repeat this connection process for the right
speaker. Remember that the positive (+ or red)
on the amplier must be connected to the positive
(+ or red) on the speaker and the negative
(- or black) to negative.
Select a signal source, such as a CD player; switch on
the amplier and slowly turn up the volume control
to check that both loudspeakers are reproducing
bass and treble information.
POWER AMPLIFIER
--+
L
+
R
SPEAKER
TO RIGHT
Positioning and Fine Tuning
To get best results from your new Tannoy
loudspeakers, it is worthwhile spending a little
time nding the optimum setup conguration.
Begin by angling the speakers towards your chosen
listening position, usually this is on the centre line
of the room, so that when seated you can just see
the inner side panel of each speaker. The front
of the loudspeaker should not be obstructed in
any way.
The loudspeakers should be located between 1.5 to
4.5 metres (5 ft to 15 ft) apart - with the listening
position set slightly further away than the speakers
are apart. Avoid positioning the loudspeakers in
corners of the room, as this will have a negative
eect on performance. For optimum performance,
we would recommend ideally maintaining a
distance of at least 0.5 metres (20 inches) from
the rear wall, and 1 metre (39 inches) from the
side. However, there is no absolute right or wrong
as it is much down to personal preference and
the diering sizes and acoustic properties of the
listening environment. The speakers may be
located close to the rear wall, in which case bass
will be increased at the expense of denition,
and stereo soundstaging will be compromised.
B6/F6 Single Wire Mode


Produkt Specifikationer

Mærke: Tannoy
Kategori: Højttaler
Model: Platinum B6

Har du brug for hjælp?

Hvis du har brug for hjælp til Tannoy Platinum B6 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Højttaler Tannoy Manualer

Tannoy

Tannoy VMS 1 Manual

29 December 2024
Tannoy

Tannoy QCI 3 Manual

29 December 2024
Tannoy

Tannoy VSX 18DR Manual

7 December 2024
Tannoy

Tannoy QFLEX 32 Manual

6 November 2024
Tannoy

Tannoy QFLEX 24 Manual

6 November 2024
Tannoy

Tannoy VXP 15Q Manual

2 September 2024
Tannoy

Tannoy VXP 12HP Manual

2 September 2024
Tannoy

Tannoy VXP 12Q Manual

2 September 2024

Højttaler Manualer

Nyeste Højttaler Manualer