Tetra Whisper 5-10i Manual

Tetra Ikke kategoriseret Whisper 5-10i

Læs nedenfor 📖 manual på dansk for Tetra Whisper 5-10i (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 6 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

Whisper® Internal

Power Filter

1. Replace Tetra® Whisper® Bio-Bag®

Cartridge Monthly.

2. Never: Clean or replace Bio-Foam® unless

damaged. Discoloration is normal and

desirable. If excessive buildup occurs,

rinse gently with room temperature

dechlorinated water.

Clean impeller yearly.

5-10i 10-30i

20-40i

Troubleshooting Guidelines

Setup

IMPORTANT:

Always unplug the Internal Filter before

inspecting or disassembling

for any reason.

18-12599

1. Attach the ﬁlter hanger to the track on the back of the ﬁlter

by aligning the water drops as shown (Fig. 1).

Clip the ﬁlter to the back wall of your aquarium frame (Fig. 2). If the hanger

doesn't ﬁt, you may need to order separate suction cups (see spare parts list

on back panel to order).

3. Insert the Filter Cartridge and Bio-Foam

® as shown (Fig. 3). (Note: the front of

the Bio-Foam® is marked “front” and should face the front of the Internal Filter.)

4. See diagram for positioning and max and min water levels. To adjust the

height of your ﬁlter, simply slide the ﬁlter up or down along the hanger track.

If you can't position the ﬁlter to your desired water level, you may need

to order suction cups (see spare parts list to order). For low water level

terrariums, you may set the ﬁlter on a ledge or aquarium bottom (Fig. 5).

5. Once the ﬁlter and water level is within the recommended parameters,

plug in the ﬁlter. Avoid using sand in the aquarium as this clogs the ﬁlter.

• Avoid placing sand in the aquarium when using this ﬁlter.

• Unplug the unit to clean the ﬁlter with a clean wet cloth. If needed,

add white distilled vinegar to the cloth, and rinse thoroughly.

• If the Bio-Foam® pad is clogged, gently wash with room temperature water

treated with AquaSafe® water conditioner to protect beneﬁcial bacteria.

• When medicating ﬁsh, remove the carbon from the Bio-Bag®

, as

carbon absorbs most medications.

• To service the impeller yearly, or if the motor is noisy, unplug the ﬁlter and remove it from the aquarium.

Remove the motor (see illustration A), open its cover, and ﬂush debris with clean water. Soak the impeller in

distilled white vinegar using a cotton swab to wipe debris, and rinse. Replace the motor into the ﬁlter and install

it in the aquarium using the instructions in this manual.

• It takes a few weeks for new aquarium water to cycle. “Cycling” a ﬁsh tank means growing healthy bacteria

on a new ﬁltration system so it ﬁlters out dangerous toxins. Tetra

® SafeStart® aquarium bacteria cycles your

aquarium immediately, so you can add ﬁsh right away.

Fig. 1

Fig. 2 Fig. 3 Fig. 4 Fig. 5

UNITED PET GROUP, A DIVISION OF SPECTRUM BRANDS, INC.

UNITED PET GROUP, UNA DIVISIÓN DE SPECTRUM BRANDS, INC.

UNITED PET GROUP, UNE FILIALE DE SPECTRUM BRANDS, INC.

3001 COMMERCE ST., BLACKSBURG, VA 24060

1-800-526-0650 • www.tetra-ﬁsh.com

® REGISTERED TRADEMARK AND TM TRADEMARK OF SPECTRUM BRANDS, INC.

MARCA COMERCIAL REGISTRADA ® Y MARCA COMERCIAL TM DE SPECTRUM BRANDS, INC.

® MARQUE DÉPOSÉE ET TM MARQUE DE COMMERCE DE SPECTRUM BRANDS, INC.

Model 5-10i Models 10-30i, 20-40i

Click Fit OR

Illus. A

Water Le vel

Nivea u d’ea u

Minimum Water Level

Niveau d ’e a u minimum

Inta ke Area

Zo ne d’a spira tion

IMPORTANT SAFETY INSTRUCTIONS

WARNING – To guard against injury, basic safety precautions should be observed, including the following:

READ AND FOLLOW ALL

SAFETY INSTRUCTIONS

DANGER – TO AVOID POSSIBLE ELECTRIC SHOCK, special care should be taken since water

is employed in the use of aquarium equipment. For each of the following situations, do not attempt repairs by yourself; return the

appliance to an authorized service facility for service or discard the appliance:

1. Unplug the appliance before installing, repositioning, cleaning, or

removing the appliance.

2. If the appliance shows any sign of abnormal water leakage, immediately

unplug it from the power source.

3. Carefully examine the appliance after installation. It should not be plugged in.

4. Do not operate any appliance if it has a damaged cord or plug, or if it is

malfunctioning or has been dropped or damaged in any manner.

5. To avoid the possibility of the appliance plug or receptacle getting wet, position

aquarium stand and tank to one side of a wall-mounted receptacle to prevent

water from dripping onto the receptacle or plug. A “drip loop,” shown in the

ﬁgure below, should be arranged by the user for each cord connecting an

aquarium appliance to a receptacle. The “drip loop” is the part of the cord below

the level of the receptacle, or the connector if an extension cord is used, to prevent

water traveling along the cord and coming in contact with the receptacle.

If the plug or receptacle does get wet, DON’T unplug the cord. Disconnect the

fuse or circuit breaker that supplies power to the appliance. Then,

unplug and examine for presence of water in the receptacle.

6. Close supervision is necessary when any appliance is used by or near children.

7. To avoid injury, do not contact moving parts or hot parts such as heaters, reﬂectors, lamp bulbs, and the like.

8. Always unplug an appliance from an outlet when not in use, before putting on or taking off parts, and before cleaning.

Never yank cord to pull plug from outlet. Grasp the plug and pull to disconnect.

9. Do not use an appliance for other than intended use. The use of attachments not recommended or sold by the appliance

manufacturer may cause an unsafe condition.

10. Do not install or store the appliance where it will be exposed to the weather or to temperatures below freezing.

11. Make sure an appliance mounted on a tank is securely installed before operating it.

12. Read and observe all the important notices on the appliance.

13. If an extension cord is necessary, a cord with a proper rating should be used. A cord rated for less amperes or watts than

the appliance rating may overheat. Care should be taken to arrange the cord so that it will not be tripped over or pulled.

14. This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will ﬁt in a polarized

outlet only one way. If the plug does not ﬁt fully in the outlet, reverse the plug. If it still does not ﬁt, contact a qualiﬁed

electrician. Never use with an extension cord unless plug can be fully inserted. Do not attempt to defeat this safety feature.

SAVE THESE INSTRUCTIONS