Tork 457Z Manual

Tork Skifte 457Z

Læs nedenfor 📖 manual på dansk for Tork 457Z (2 sider) i kategorien Skifte. Denne guide var nyttig for 7 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
MAINE
VT
NH
MASS
NEW YORK
PENNS YLVANIA
OHIO
INDILLINOIS
KENT UCKY VIRGINIA
NORT H CAROLINATE NNESS EE
WEST
VIRGINIA
SOUT H
CAROLINA
GEORG IAALABAMA
MISS
FLORIDA
LOUISIANA
ARKANSAS
OKLAHOMA
MISSOURI
TE XAS
KANSAS
NEW MEXICO
MEXICO
ARIZO NA
CALIFORNIA
NEVADA UTAH COLORADO
NEBRASKA
WYOMING
IDAHO
OREGO N SOUT H DAKOTA
IOWA
WISCONSIN
MICHIGAN
MINN
NORT H DAKOTA
MONTANA
WASHINGT ON
RHODE ISL AND
CONNECT ICUT
NEW JE RSEY
MARYLAND
DELAWARE
ASTRONOMIC LATITUDE ZONES
ZONES DE LATITUDE
ZONAS ASTRONOMICAS (LATITUDES)
SUSA
CUSA
NUSA
ALAS
HAWI
PROGRAMMING INSTRUCTIONS
457Z
A DIVISION OF NSi INDUSTRIES, LLC
PLEASE READ ALL INSTRUCTIONS FIRST
ONE YEAR LIMITED WARRANTY: If this product
fails because of a manufacturing defect within
one year after purchase, we will, at our option,
either repair or replace it at no charge. Our
warranty does not cover damage caused by
accident, abuse or misuse. We assume no
further liability with respect to the sale or use
of this product. THIS WARRANTY IS IN LIEU
OF ALL OTHER WARRANTIES, EXPRESSED OR
IMPLIED, INCLUDING THE WARRANTY OF
MERCHANTABILITY. We make no warranty with
respect to the fitness of any goods for the users
particular application. This warranty gives you
specific legal rights, and you also may have other
rights which vary from state to state.
It is our intent to provide accurate and current
specification information. However, in the interest
of product improvement, TORK may alter the
specifications or constructional details without
prior notice.
SET
MODE ENTER
R
1.0 INSTALLATION INSTRUCTION
• Plug the timer into a 120VAC receptacle. If you charge battery
overnight, the unit can be removed and programmed without
AC power.
• Press the (RESET) button by using an insulated tool.R
• Press the to start the timer.ENTER
2.0 SET TIME AND DATE (CALD)
• Press the button two times to display flashing.MODE CALD”
• Press the button to start current time setting mode. ENTER
• Using buttons change year, then press button.SET
• Continue to using and button to enter current month, SET
date, hour, minutes, and seconds.
• Press the button to save the current time setting and return ENTER
to clock mode.
3.0 SET SCHEDULE
• Press the button to display “PROG” flashing.MODE
• Press the button to display “PROG 1 ON”. This is the first ENTER
of 20 ON/OFF pairs. For first ON program, press . To go to other SET
programs, press .
3.1 SELECT DAYS
• All days are flashing. Use to choose a different set of days,
then press .SET
3.2 SET ON
• Use to choose:
a) “TIME” for a program with user set times
b) “SNUP” for a timer calculated sunrise time that will change daily
throughout the year.
c) “SNST” for a timer calculated sunset time that will change daily
throughout the year.
• Then press . If “TIME” selected: Use buttons to change SET
hour, then press button. Repeat for minutes.SET
3.3 SET OFF
• “PROG 1 OFF” is flashing on display. Press .SET
• All days are flashing. Use to choose a different set of
days, then press .SET
• Use to choose:
a) “TIME” for a program with user set times,
b) “SNUP” for a timer calculated sunrise time that will change daily
throughout the year.
c) “SNST” for a timer calculated sunset time that will change daily
throughout the year.
• Then press . If “TIME” selected: Use buttons to change SET
hour, then press button. Repeat for minutes. Press .SET SET
• Repeat steps for a total 20 ON and 20 OFF time settings.
• Press the button to finish programming set and return to ENTER
clock mode.
4.0 OPTIONAL SUNSET/SUNRISE TIME ZONES
• Press the button three times to display “ZONE” flashing.MODE
• Press the button to start Zone setting mode.ENTER
• Use the keys to display the correct zone.
---
NOTE: NUSA (Default) = North USA, CUSA = Center USA, SUSA = South
USA, ALAS = Alaska&Northern Canada, HAWI = Hawaii&Puerto Rico.
----
• Press the button to save the setting and return to clock ENTER
mode.
5.0 OPTIONAL SUNSET/SUNRISE OFFSET
---
NOTE: This mode displays calculated sunset/sunrise. You can change to
turn ON/OFF earlier or later with this mode.
---
MODE• Press the button four times to display “SUN± ” flashing.
• Press the button to start offset mode .ENTER
• Screen displays today’s SNUP (sun up) time flashing. Use or
to change default time.
• Press and screen displays today’s SNST (sunset) time flashing. SET
Use to change default time.
• Press to complete the setting and back to normal clock ENTER
mode.
6.0 OPTIONAL CHANGE DAYLIGHT SAVINGS TIME (DST)
---
NOTE: Skip this step for default daylight savings dates. Follow instructions
below only if you need to remove or change. MANU (Manual Mode) – no
DST change by timer. NEW mode - change dates to something other than
default dates.
----
• Press the button five times to display “DST” flashing.MODE
• Press the button to choose daylight savings times.ENTER
• Use the to choose daylight savings options.
a) The display shows “INIT”. For timer to follow current U.S. DST
dates, press . ENTER
b) The display shows “MANU”. For no DST adjustment, press .ENTER
c) The display shows “NEW”. For modified DST dates, consult
technical support phone line.
7.0 COUNTDOWN TIME SETTING
---
NOTE: Countdown mode will postpone the manual off for a preset period.
As an example, press button to turn off lights and timer will wait five
minutes before load is shut down. This will give you time to exit the room.
---
• Press the button to display “PROG” flashing.MODE
• Press the button to display “PROG 1 ON”.ENTER
• Press the once to bring the Countdown time setting.
• Press for the Countdown (dL) screen.SET
• Press to choose length of time.
• Press to complete the setting and back to normal clock ENTER
mode.
8.0 RANDOM ON/OFF TIME
• Pressed key & simultaneously to set the Random function. SET
Display shows “RND”.
• To Cancel Random function simply repeat above procedure. The
“RND” sign will disappear from display.
9.0 OVERRIDE BUTTON FUNCTIONS ( )
• Press one time to turn timer ON or OFF.
10.0 ACTIVATE COUNTDOWN
---
NOTE: To activate Countdown step 7 must be completed and the timer in
the ON position.
---
• Press
RATINGS
• 120V 15A, 1800W General Purpose
• 120V 15A, 1800W Resistive
• 120V, 960W Tungsten
• 120V 1/3 HP, TV-5
LI-846
FOR TECHNICAL SUPPORT: SOUTIEN TECHNIQUE : PARA COMUNICARSE CON EL SERVICIO TÉCNICO: techsupport@nsiindustries.com 877.230.7874
http://waterheatertimer.org/Tork-consumer-timers-and-manuals.html
__________________________________________________________________________


Produkt Specifikationer

Mærke: Tork
Kategori: Skifte
Model: 457Z

Har du brug for hjælp?

Hvis du har brug for hjælp til Tork 457Z stil et spørgsmål nedenfor, og andre brugere vil svare dig




Skifte Tork Manualer

Tork

Tork SS720A Manual

5 Oktober 2024
Tork

Tork 451D Manual

18 September 2024
Tork

Tork 701A Manual

15 August 2024
Tork

Tork 460D Manual

6 August 2024
Tork

Tork SS721Z Manual

5 August 2024
Tork

Tork 457Z Manual

29 Juli 2024
Tork

Tork SS721ZA Manual

18 Juli 2024

Skifte Manualer

Nyeste Skifte Manualer