Truetone 1 Spot Voltage Doubler Manual

Truetone Ikke kategoriseret 1 Spot Voltage Doubler

Læs nedenfor 📖 manual på dansk for Truetone 1 Spot Voltage Doubler (1 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 12 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/1
18Vdc or 24Vdc
Pedal
IN OUT
WARNING:
Use the Voltage Doubler cable only from 9Vdc or 12Vdc
outputs. 9Vdc is converted to 18Vdc. 12Vdc is converted to
24Vdc. Do not use with input voltage greater than 12Vdc.
WARNING:
Check with the pedal manufacturer before using the
Voltage Doubler cable. Truetone is not liable for
improper use of this cable that causes damage to your
pedal. Many effects pedals will be damaged by
18Vdc and most will be damaged by 24Vdc.
FCC Notice:
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
NOTE
: Polarity for both input and output is center pin negative. If you have a pedal that
requires center pin positive polarity, please use a Reverse Polarity Converter (CYR) or an
L6 Converter (CL6), sold separately by Truetone. For example, old E-H Deluxe Memory
Man pedals need a CL6 Converter, connected to the Output of the Voltage Doubler.
Can I use this on an MC5 or MC8 daisy-chain with my 1 SPOT? Yes
Can I use this with a 1 SPOT Pro? Yes, on 9Vdc or 12Vdc outputs. (Not 9Vac!) Just
plug one of the DC cables from your 1 SPOT Pro into the Voltage Doubler.
Can I use this with other musician power supplies? Yes, on 9Vdc or 12Vdc outputs
with center pin negative polarity on 2.1mm x 5.5mm barrel plugs.
Can I use this with analog pedals? If the pedal maker says your pedal can work with
18Vdc or 24Vdc, then yes. Otherwise, no.
Can I use this with digital pedals? Probably not, as most digital pedals cannot work on
anything higher than 9V. There are a few digital pedals that work on 18Vdc however, so
please check your pedal owner’s manual or contact the manufacturer to be sure. Do NOT
just plug the Voltage Doubler cable into anything to “see if it will work”. As stated above,
Truetone is not liable for your pedal being damaged by plugging in this cable when your
pedal is not designed for 18Vdc or 24Vdc.
How many milliamps (mA) can the Voltage Doubler cable handle? 100mA
Truetone.com
X


Produkt Specifikationer

Mærke: Truetone
Kategori: Ikke kategoriseret
Model: 1 Spot Voltage Doubler

Har du brug for hjælp?

Hvis du har brug for hjælp til Truetone 1 Spot Voltage Doubler stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Truetone Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Gigabyte

Gigabyte ODIN GT 550W Manual

23 November 2024
Stamos

Stamos S-PLASMA 60U Manual

23 November 2024
Velbus

Velbus VMBPIRO-W-20 Manual

23 November 2024
Honor

Honor 90 Pro Manual

23 November 2024
Honor

Honor 80 SE Manual

23 November 2024
Medela

Medela Safe & Dry Manual

22 November 2024
Jane

Jane First Potty Manual

22 November 2024