Uni-T UT202A Manual

Uni-T Måleudstyr UT202A

Læs nedenfor 📖 manual på dansk for Uni-T UT202A (2 sider) i kategorien Måleudstyr. Denne guide var nyttig for 16 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/2
Overview
T O t cov s f t on his pera ing Manual er in orma ion
sa and cau ions lea read he relevanfety t . P se t t
in orma ion care ull and observe allf t f y t he
Warnings and Notes strictly.
Warning
To av c c s s y, d oid ele tri hock or per onal injur rea
t “Safety Inf t carefully before usinghe orma ion”
the Meter.
Model UT202A is 2000-count stable, safe and
reliable digital clamp multimeter(hereafter
referred to as "the Meter"). It is designed with
large-scale integrated circuits and A/D
converter as the core as well as the overload
protection and novel structure, which make
it a superb tool for electricians.
T t AC/ V t , AC he Me er can measure DC ol age
Current, Resistance, Diodes, and Continuity.
Unpacking Inspection
Open the package case and take out the Meter.
Che the following item efull for anck s car y y
missing or damaged part:
Item Description Qty
1 English Operating Manual 1 piece
2 Test Lead 1 pair
In the ent ou find an mis ing damaged ev y y s or
part please contact your dealer immediately.
Safety Information
Thi eter co pl ies w ith the standards M m
IEC61010 Pollu ion Degree ervol ag: t 2, Ov t e
Category (CATII 600V, CAT III 300V) and Double
Insulation.
CA v PORT LE TII: Local le el, appliance, AB
E P MEN T c s tr s t QUI et ., with maller an ien
overvoltages than CATIII.
CAT III: Distribution level, installation, with fixed
smaller transient overvoltages than CAT IV
Use t Met on eci in th op ting he er ly as sp fied is era
manual herwise he pro ec ion provided, ot t t t by
the Meter may be impaired.
In t s , a W ti es c t s hi manual arning iden fiondi ion
and ac ions ha pose hazards he use t t t to t r, or
may damage the Meter or the equipment under
test.
A user Note identifies the information that
should pay attention to.
Warning
To t s l avoid possible elec ric shock or per ona
injur and avoid pos ible damagey, to s to the
Meter or to the equipment under test, adhere to
the following rules:
.esac eht tcepsni reteM eht gnisu erofeB ●
Do no use he Me er damaged or t t t if it is the
case (or part of the case) is removed. Look for
c ks s . P a t to the rac or mi sing pla icst ay tten ion
insulation around the connectors.
● I ns t t e s f d pect he st lead or damage
insula ion or me al Check he est exposed t . t t t
lead or on inui Repla damaged ess f c t ty. ce t t
leads with identical model nu ber ele tri m or c cal
specifications before using the Meter.
● t y t t t v t , Do no appl more han he ra ed ol age
as marked on the Meter, between the terminals
or be ween any erminal and grounding t t . the If
value be mea ured un nown to s is k , use the
● W t t , hen measuremen has been comple ed
disconnect the onne tion between the te c c st
lead and the ir uit unde te t, re ove ths c c r s m e
te y f t t t s of sting leads awa rom he inpu erminal
the Meter and turn the Meter power off.
● T t y s h s c in he ro ar witc hould be pla ed
t t t y c v of he righ posi ion and no an hangeo er
range shall be made when measuremen t is
conducted to prevent damage of the Meter.
● Do t t t t n no carry ou he measuremen whe
the Meter’s back case and battery compartment
are not closed to avoid electric shock.
● Do not input higher than 600V between the
Me erminal and he grounding avoiter’s t s t to d
electric shock and damages to the Meter.
● W t t k at effe ive hen he Me er is wor ing an ct
v t ov V V AC, ol age er 60 in DC or 30 rms in
special care should be taken for there is danger
of electric shock.
● Use s, c d the proper terminal fun tion, an
range for your measurements.
● Do t s t t t an no use or ore he Me er in
en ironmen high emperature humidiv t of t , ty,
explosives, inflammables and rong magne st tic
f . T f of t t y ield he per ormance he Me er ma
deteriorate after dampened.
● W us t te k y r hen ing he st leads, eep ou
fingers behind the finger guards.
● Disconnect e circuit power and discharg
all high-vol age capaci ors be ore in t t f t est g
resistance, continuity and diode.
● Replace the battery as soon as the battery
indicator appears. With a low battery, the
Meter ight odu false readings that ca m pr ce n
lead to electric shock and personal injury.
● W s vic t ter, use y hen er ing he Me onl use
the replacement parts with the same model
or identical electrical specifications.
● The internal circuit of the Meter shall not be
altered at will to avoid damage of the Meter and
any accident.
● So th t t be ft clo and mild de ergen should
used to clean the fa of the ete whe sur ce M r n
servi ing No abra and ol en houldc . sive s v t s be
us to v t t s face of t t f m ed pre en he ur he Me er ro
corrosion, damage and accident.
● The Meter is suitable for indoor use.
● Turn the Meter off when it is not in use and
t t t b wh t us g r a l g time. ake ou he attery en no in fo on
● Constantly check the battery as it may leak
when ha been ing or ome ime repla it s us f s t , ce
t t as as k A he bat ery soon lea ing appears.
leaking battery will damage the Meter.
International Electrical Symbols
AC (Alternating Current)
DC (Direct Current)
AC or DC
Grounding
Double Insulated
Warning. Refer to the Operating Manual
Low Battery Indication
Continuity Test
Diode
Conforms to Standards of European Union
The Meter Structure (See Figure 1)
Figure 1
1. Input Terminals
2. LCD Display
3. Functional Buttons
4. Rotary Switch
5. Trigger: press the lever to open the
transformer jaws. When the pressure on the
lever is released, the jaws will close.
6. Hand Guards: to protect user’s hand from
touching the dangerous area.
7. Transformer Jaws: designed to pick up the
AC current flowing through the conductor.
It could transfer current to voltage. The
tested conductor must vertically go through
the jaw center.
maximum measurement position and reduce the
range step by step until a satisfactory reading is
obtained.
Functional Buttons and Auto Power Off
1. HOLD
Press to enter and hold mode. Press HOLD exit
and hold button while tu ning on th HOLD r e
Meter, auto power off will be canceled.
2. MAX
P to st t t of ress MAX ar recording and upda ing
maximum values.
3. SELECT
Under ranging, resistance Ω
mea uremen mode de aul press t is f t, s SELECT
to s ct t ty s t e ele con inui mea uremen mode or diod
measurement mode.
4. Auto Power Off
To preserve battery life, the Meter automatically
goe in “sleep” mode you do no press ans to a if t y
button for around 10 minutes. The Meter can be
activated by pressing any effective button (refer
to T Eff t of F t Bu , he ec iveness unc ional ttons)
then return to the display for the fun tio c n
selected previously.
5. Buzzer
The buzzer sounds every time a effective button
is pressed down. r o When the mete will aut
power in minu he buzzer beeps iv off 1 te t f e
times. Before power off there will be a long time
buzzer beeps.
6. The Effectiveness of Functional Buttons
No er un ional bu on can be edt ev y f ct tt s us on
ev y t y s t sit . B t e er ro ar wi ch po ions elow abl
des ribe which unc ional bu ons can bec f t tt used
on which rotary switch positions
Rotary Functional Buttons
Switch SELECT MAX HOLD
Positions
Ω • N/A •
N/A • •
N/A • •
A 20A N/A • •
A 200A N/A • •
A 600A N/A • •
Display Symbols (See Figure 2)
Number Description
1 Indicator for AC voltage or current
2 Indicator for DC voltage
3 The battery is low.
Warning: To avoid false readings, which
could lead to possible electric shock or
personal injury, replace the battery as soon as
the battery indicator appears.
4 The Meter is in the auto range mode in
which the Meter automatically selects
the range with the best resolution.
5 Test of diode
6 The continuity buzzer is on
7 Maximum reading displayed
8 Data hold is active
9 Amperes (amps). The unit of current.
10 Ω: Ohm. The unit of resistance.
kΩ:Kilohm. 1000 ohms
MΩ:Megohm. 1,000,000 ohms
11 V: Volts. The unit of voltage.
mV: Millivolt. 0.001 volts
12 Indicates negative reading
Figure 2
Measurement Operation
A. Measuring DC Voltage (See Figure 3)
Warning
To avoid harm to you or damage to the Meter
from eletric hoc do not attempt to mea ur s k, s e
voltages higher than 600V AC/DC.
To m re v c as easu DC oltage, onnect the Meter
follows:
1. Insert the red test lead into the
terminal and the black test lead into the
terminal.COM
2. Set the rotary switch to .
3. Connect the test leads across with the object
being measured.
VΩ
The measured value shows on the display.
Figure 3
Note:
W v t s t s n hen DC ol age mea uremen ha bee
comple ed sconnec he nne ion be eet , di t t co ct tw n
the testing leads and the ci uit unde te an rc r st d
remove testing leads from the input terminals.
B. Measuring AC Voltage (See Figure 4)
Warning
To avoid harm to you or damage to the Meter
from eletric hoc do not attempt to mea ur s k, s e
voltages higher than 600V AC/DC.
To AC t , c t t t as measure vol age onnec he Me er
follows:
1. Insert the red test lead into the
terminal and the black test lead into the
terminal.COM
2. Set the rotary switch to .
3. Connect the test leads across with the object
being measured.
The measured value shows on the display.
VΩ
Figure 4
Note:
When AC oltage easu ent has bee v m re m n
comple ed sconnec he nne ion be eet , di t t co ct tw n
the testing leads and the ci uit unde te an rc r st d
remove testing leads from the input terminals.
C. Measuring Resistance (See Figure 5)
Warning
To av to t t to the oid damage he Me er or
devic d test, d c nect it po and es un er is on circu wer
discharge all the high-voltage capacitors before
measuring resistance.
To t , t t t as measure resis ance connec he Me er
follows:
1. Insert the red test lead into the
terminal and the black test lead into the
terminal.COM
2. Set the rotary switch to ; resistance
measurement (Ω) is default or press
button to select measurement SELECT Ω
mode
3. Connect the test leads across with the object
being measured.
The measured value shows on the display.
Note:
● t te f m Separating he objects being sted ro
t c c t s c t a e he ir ui when mea uring an ob ain mor
accurate result.
Ω
VΩ
Figure 5
● When r m rem n esistance easu ent has bee
comple ed sconnec he nne ion be eet , di t t co ct tw n
the testing leads and the ci uit unde te an rc r st d
remove testing leads from the input terminals.

Produkt Specifikationer

Mærke: Uni-T
Kategori: Måleudstyr
Model: UT202A

Har du brug for hjælp?

Hvis du har brug for hjælp til Uni-T UT202A stil et spørgsmål nedenfor, og andre brugere vil svare dig


Måleudstyr Uni-T Manualer

Uni-T

Uni-T UT18D Manual

16 December 2024
Uni-T

Uni-T UT363s Manual

16 December 2024
Uni-T

Uni-T UT383s Manual

16 December 2024
Uni-T

Uni-T UT575B Manual

1 September 2024
Uni-T

Uni-T UT503PV Manual

1 September 2024
Uni-T

Uni-T UT225B Manual

31 August 2024
Uni-T

Uni-T UT377C Manual

31 August 2024
Uni-T

Uni-T UT387S Manual

31 August 2024
Uni-T

Uni-T UT243 Manual

31 August 2024
Uni-T

Uni-T A13T Manual

31 August 2024

Måleudstyr Manualer

Nyeste Måleudstyr Manualer

Steinberg

Steinberg SBS-MT-100 Manual

16 December 2024
Steinberg

Steinberg SBS-SM-135C Manual

16 December 2024
Steinberg

Steinberg SBS-LF-147 Manual

16 December 2024
Steinberg

Steinberg SBS-DL-123E Manual

15 December 2024
Steinberg

Steinberg SBS-LF-116 Manual

15 December 2024
Steinberg

Steinberg SBS-LF-140 Manual

15 December 2024
Steinberg

Steinberg SBS-LF-141 Manual

15 December 2024
Steinberg

Steinberg SBS-DL-123D Manual

15 December 2024
Steinberg

Steinberg SBS-DT-999 Manual

15 December 2024
Steinberg

Steinberg SBS-SM-130C Manual

15 December 2024