Valcom V-1070 Manual

Valcom Højttaler V-1070

Læs nedenfor 📖 manual på dansk for Valcom V-1070 (2 sider) i kategorien Højttaler. Denne guide var nyttig for 8 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

Issue 1

1 947662

Machine

Shop

(Noisy) 90

10' 20' 30' 40' 50'

Shipping

(Moderate)

Waiting

Rooms

(Quiet)

Talkback not recommended above 80dB

TYPICAL REPLY DISTANCE CHART

Maximum Talkback Reply Distance

V-1070

P-TEC SURFACE MOUNT

TALKBACK CEILING SPEAKER

INTRODUCTION

The V-1070 is a surface mounted speaker that

is used with Valcom “Handsfree” Talkback Page

Control units. The speaker is designed for

interior use only. The baffle is designed for

mounting on acoustic tile, such as those

normally found in suspended-ceilings and can

be mounted without cutting large holes in the

tile. The mounting pins can be removed for

mounting in a hard ceiling. The speaker

housing has screw holes for securing speaker

without mounting pins. Although the

P-TEC speakers are designed specifically for

standard suspended ceilings, they can be used

on many types of ceiling materials.

SYSTEM DESIGN

General

The 45 Ohm Talkback Speakers are designed to

be used with the Valcom "handsfree" talkback

control units. In combination with these units,

they will provide both loudspeaker and talkback

functions.

A standard Valcom talkback paging system is

made up of three basic components:

1. A talkback page control unit

2. Speakers (45 Ohm)

3. A power supply

Consult Valcom's VSP - Handsfree Talkback

Paging (Part # 947099) for detailed information

on selecting the control unit and power supply.

Dimensions/Weight

• 8.00” Dia x 2.50” H (20.32cm x 6.35cm)

• 0.75 lbs. 0(.34 kg)

INSTALLATION ( )see Figure 1

1. Lift the adjacent ceiling tile and slide it out of

the way.

2. Pierce hole in tile where speaker is to be

mounted with a screwdriver. Feed wire

through hole to connect to speaker.

3. Make connections to speaker.

4. Install the speaker by inserting the mounting

pins through the ceiling tile and hold the

speaker in place.

5. Place the speaker mounting clips over

mounting pins (so pins slide through clips).

Connections

Two conductor twisted wire is required for the 45

Ohm talkback speakers. Standard 22 or 24

gauge station wire is acceptable. Shielded wire

is not required or recommended. Connections

are as follows:

• Speaker out from page control to speaker tip

• Speaker common to speaker ring

IMPORTANT

The speaker is no better than your ears. If you cannot

carry on a conversation at normal voice levels over the

required talkback distance, then the talkback page

equipment will not function satisfactorily.

Use common sense when mounting a talkback

speaker. The speaker should be as close as possible

to the area where talkback is desired.

It should not be mounted close to or pointed at, noise

producing equipment such as fans, air conditioners,

machinery or compressors.

Produkt Specifikationer

Mærke:	Valcom
Kategori:	Højttaler
Model:	V-1070

Har du brug for hjælp?

Hvis du har brug for hjælp til Valcom V-1070 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Højttaler Valcom Manualer

Valcom VIP-421 Manual

6 September 2024

Valcom InformaCast VIP-120-IC Manual

6 September 2024

Valcom InformaCast VIP-402A-IC Manual

6 September 2024

Valcom VIP-422A Manual

6 September 2024

Valcom V-1019B Manual

6 September 2024

Valcom V-1020C Manual

6 September 2024

Valcom S-522A-2 Manual

6 September 2024

Valcom Clarity S-515 Manual

6 September 2024

Valcom V-1023C Manual

6 September 2024

Valcom V-1040 Manual

6 September 2024

Højttaler Manualer

Nyeste Højttaler Manualer

Tannoy QFLEX 32 Manual

6 November 2024

Tannoy QFLEX 24 Manual

6 November 2024

Tannoy ARCO GRILLE CMS 603-WH Manual

6 November 2024

Tannoy AUTOGRAPH MINI-OW Manual

6 November 2024

5 November 2024

5 November 2024

5 November 2024

5 November 2024

5 November 2024

5 November 2024