Vantec NST-520S3-BK Manual

Vantec Ikke kategoriseret NST-520S3-BK

Læs nedenfor 📖 manual på dansk for Vantec NST-520S3-BK (10 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 39 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/10
Copyright © 2015 Vantec Thermal Technologies. All Right Reserved. | All Registered Trademarks Belong To Their Respective Companies.
Information in this document is subject to change without notice.
Reproduction of these materials in any manner whatsoever without written permission is strictly forbidden.
Printed in China
Printed on Recycled Paper.
Installation Guide
For NST-510S3-BK (9.5mm only). For NST-520S3-BK (12.7mm) see back page.
USB 3.0 Slim SATA
Optical Drive Enclosure
The Operating System will detect USB Mass storage device
connected and load the necessary drivers built into the
Operating System. No other drivers are needed.
?
8. Once the drivers are installed the Optical drive is ready for use.
OK
9.
Carefully slide out the optical drive tray.
2.
Slide the Tray with the secured optical drive into the
Aluminum housing and secure with two screws.
6.
Slide the Optical drive on the Tray until the Slim SATA interface on
the Optical drive dock completely with the Tray Slim SATA interface.
4.
If the Front Plate of your Optical Drive is using a Protruding or
Curve Front Plate, please use the provided Front Plate to replace
it. Follow the picture showing the hook to remove and replace.
3.
Flat Front Plate
Side View
Protruding or
Curve Front Plate
1) Eject the Optical Tray by inserting a
paper clip into the eject hole on the
front of the Optical drive.
2) Note the location and direction of
the hooks on the provided Flat Front
Plate, unhook each hook slowly.
3) Replace it with the provided Flat
Front Plate back onto your Optical
drive. Note the location of the 4 hooks.
Secure the Optical Drive to the Tray using the provided
small screws on both sides.
5.
Connect the USB cable to the Optical unit and your system USB port.
The Optical unit is bus powered. It will draw power from the USB port.
7.
USB 3.0 Cable USB 3.0 Port
Optional USB
Power Connection
*Optional USB Power Connection:
If your Optical Drive need more power than 1 USB 3.0
port can provide. please use the additional USB power
connection to your system, If you are not sure connect both.
Verify the package contents.
1.
USB 3.0 Cable
Front Plate


Produkt Specifikationer

Mærke: Vantec
Kategori: Ikke kategoriseret
Model: NST-520S3-BK
Bredde: 136 mm
Dybde: 151 mm
Højde: 20 mm
Produktfarve: Sort
Husmateriale: Aluminium, Plastic
Hurtig start guide: Ja
Kabler inkluderet: USB
USB-tilslutning: Ja
USB version: 3.2 Gen 1 (3.1 Gen 1)
Størrelse: - "
Integreret USB-kabel: Ingen
Optisk drevgrænseflade: SATA

Har du brug for hjælp?

Hvis du har brug for hjælp til Vantec NST-520S3-BK stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Vantec Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Senal

Senal SCI-3212MP Manual

22 November 2024
Senal

Senal OLM-2S-P Manual

21 November 2024
Senal

Senal ME-220-CL Manual

21 November 2024
Senal

Senal ASM-4 Manual

21 November 2024
Senal

Senal CS-88 Manual

21 November 2024
Senal

Senal CSP-162 Manual

21 November 2024
Senal

Senal MXGN-ICS Manual

21 November 2024
Dubatti

Dubatti Board Two Manual

21 November 2024
Senal

Senal ASM-3 Manual

21 November 2024