Velbon VS-443D Manual

Velbon Kamerastativ VS-443D

Læs nedenfor 📖 manual på dansk for Velbon VS-443D (1 sider) i kategorien Kamerastativ. Denne guide var nyttig for 10 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/1

１-１２

※

QHD-53D

1610mm

200mm

240mm

580mm

23/20/17.2/14.4mm

1850g

3000g

VS-443D

１-２

VS-443D

OPERATING MANUAL

Crank handle

Individual part name

Thank you very much for choosing Velbon tripod. Please read this manual carefully

before you start using this tripod.

Shoe lever

Quick release plate QB-62

Elevator

Leg tip

Low angle position

Knob for leg angle

Specifications

Head

Maximum height with Elevator

Elevator movement

Minimum Height

Folded length

Leg diameters

Section of legs

New weight

Suggested loading weight

Each specification is based on the estimated drawings. It may change depending on the actual parts assembled.

How to attach your camera How to attach your camera

How to install

Caution: Please hold your camera surely when attach/detach quick release plate to the camera body.

Also when install to the tripod/head, please make sure it locks firmly before you release your hand.

Locking knob

Elevator stopper

Grip knob for

adjusting

Leg locking lever

Release

Shoe Lever

Then plate

rises up

Shoe Lever

Bubble Leveler

Rotate shoe lever to release quick

release plate (QB-62)

Then QB-62 rises up to be slide out.

Support your camera or other

equipment with one hand,then with

the other hand gradually release the

Locking knob by turning

anti-clockwise. You are now able to

freely adjust the position of your

camera in all 3 axes (vertically,

horizontally and left –to-right) to the

desired position.

Rotate locking lever until quick-shoe

(QB-62) can be removed from the

socket. Turn camera screw clockwise

to attach QB-62 to the base of your

camera.

Place quick-shoe(QB-62) into socket

and lock in place by rotating lever.

Camera Screw

Quick-Release Plate

Shoe Lever

３How to use the head ９

※Head goes down in the case.

When carrying tripod in the case, put

head down so that you may carry

easier on the shoulder.

Storage

８

Watch your fingers not to be bound by

the locking lever.

Leg locking lever

How to extend legs

４４-１

Lock

Unlock

Rotating Grip knob for adjusting to

unlock direction as seen in above

drawing. Determining to the direction

of the extension, lock by rotating the

Grip for locking direction firmly.

How to use the elevator

Grip knob

Raise up

-２

Lock

Unlock

How to use the elevator

Unlocking the Elevator stopper, rotate

the Crank handle to extend the

Elevator. When the elevator extends

to the desired position, lock the

Elevator stopper firmly.

Caution: Hold your camera body while

operating elevator up/down carefully.

５-１

Tighten surely !

Caution to operate

In the positioning to horizontal way,

the center part of the Elevator may

come to Loosen. So make sure

locking the Grip Knob firmly. Tighten

all the stoppers on the head and

tripod surely.

When extending horizontal,

the head is apt to loosen

depending on the angle of

the arm.

Caution: The longer Elevator extending,

the easier to be loosen the tension of the

Stopper or Grip Knob. Please grasp the

Grip knob to hold tightly.

７６

※

Locking knob

Lock all the stoppers on the head and

tripod, rotate head to anti-clockwise

direction to unscrew the head from

the tripod.

Screw size UNC 1/4 inch.

How to remove the head

※

７-１

Knob for leg angle

① While legs are closed, slide the

Knob for leg angle to right till it

sounds Click to stay. Then legs are

allowed to open to the full low angle

position.

By pushing the Reset button, the leg angle

can be back to the normal position.

Reset button

Open

Slide

Leg- angle adjusting -２

Closing

Click !

Automatically leg angle is

back to left for Semi low angle

position with a click.

② While closing the legs from Full low

angle position, back to the Semi low

angle position automatically, sliding to

left with a click.

Leg- angle adjusting ７-３

Click !

Closing

Slide to left further

③Closing further, the leg angle

position changing to the Standard

automatically. Each leg can be

adjusted the angle independently for

standing the tripod in the uneven

terrain.

Leg- angle adjusting

５-２

Watch your camera,

not to be laid down

Caution to operate

In case of setting whole unit including

the camera, lens and tripod with even

deeper angle of the Elevator

extending, be careful to be laid down

by losing the balance. Hold the Grip

Knob tightly or hold the tripod leg until

the balance become steady.

Caution: Be aware that it becomes

easier to be laid down when the Elevator

extends to the horizontal way. Please keep

holding tripod or camera in well supported

condition.

Folding

Extending

Raise the Leg locking lever to extend

the legs till desired position. Then

lock the Legs firmly. When using the

tripod legs less than fully extension,

use the upper legs than lower ones

because diameters are bigger and

streadier.

Produkt Specifikationer

Mærke:	Velbon
Kategori:	Kamerastativ
Model:	VS-443D
Vægt:	1850 g
Produktfarve:	Sort
Materiale:	Aluminium
Formål:	Universel
Montering:	1/4", 3/8"
Antal ben:	3 ben
Højde (min.):	240 mm
Højde (maks.):	1610 mm
Maksimal vægtkapacitet:	5 kg
Antal benafsnit:	4
Tripod hoved:	QHD-53D