Vemer Fiuto Manual

Vemer Detektor Fiuto

Læs nedenfor 📖 manual på dansk for Vemer Fiuto (3 sider) i kategorien Detektor. Denne guide var nyttig for 35 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/3

Vemer S.p.A.

I - 32032 Feltre (BL) • Via Camp Lonc, 16

e-mail: info@vemer.it - web site: www.vemer.it

MKIS01075-010 Mod. FIUTO

Flush-mounting detector for monitoring air quality by measuring

CO2 equivalent (CO2eq), designed to be installed in closed environments

such as shops, offices, public places, etc.

The output relay is activated when the equivalent CO2 concentration exceeds

the intervention value set with the knob, and can be used, for example,

to activate ventilation units for air exchange. The device performs actions

of 1B type and is intended to operate in environments with pollution degree 2

and overvoltage category III (EN 60730-1).

Code Model Descritpion

VE788100 Fiuto Flush-mounting air quality detector

SAFETY WARNINGS

During product installation and operation it is necessary to observe

the following instructions:

1) The device must be installed by a qualified person, in strict compliance

with the connection diagrams.

2) Do not power or connect the device if any part of it is damaged.

3) After installation, inaccessibility to the connection terminals without

appropriate tools must be guaranteed.

4) The device must be installed and activated in compliance with current electric

systems standards.

5) Before accessing the connection terminals, verify that the leads are not live.

6) In the electrical system of the building where the instrument must be installed,

a protection device from the overcurrents must be present.

TECHNICAL SPECIFICATIONS

• Power supply: 230Vac (-15% ÷ +10%) 50/60Hz

• Absorption: 4VA (0.5W)

• Installation on 3 modules box (503 type)

• Terminals:

– 3 terminals for 1.5 mm2 cables for output relay

– 2 terminals for 1.5 mm2 cables for power supply

• Output: bistable relay 5(3)A / 250 Vac

• Minimum time between a switching and the next one: 1 minute

• Regulation type: on/off with fixed differential of 50 ppm

• Regulation range: 400 ppm÷ 2000 ppm

• 2-position selector switch: always off, automatic

• Operating temperature: 0 ÷ +50°C

• Storage temperature: -10°C ÷ + 60°C

• Operating humidity: 20 ÷ 90% non condensing

• Protection degree: IP40

• Insulation: reinforced among accessible parts (frontal) and all other terminals

• Mechanical locks on the knob to limit the adjustment range

The adapters inside the box allow the monitoring of the following cover plates:

For information about the possibility to adapt the device with different

cover plates from those listed, contact the Technical Service.

* through mount that you can buy on request (code VE767500)

• All the above trademarks are the property of their respective owners

ABB Chiara series

ABB Mylos series

Ave S44 series

Bticino Axolute series

Bticino Axolute Air*

Bticino Light series

Bticino Light tech series

Bticino Living series

Bticino Livinglight series

Bticino Livinglight Air series

Bticino Matix series

Gewiss Chorus series

Vimar Eikon series

Vimar Eikon Evo series

Vimar Idea series

Vimar Plana series

Vimar Arké series

User Manual

FLUSH-MOUNTING AIR QUALITY DETECTOR

 Read all instructions carefully

OPERATION

PACKAGE CONTENTS

WIRING DIAGRAMS

ADJUSTABLE COVER PLATES

When we talk about air quality, we usually mean the concentration

of carbon dioxide present.

However, it is established that there are, in addition to carbon dioxide (CO

2),

also other gases responsible for the decay of air quality and, consequently,

of the greenhouse effect: methane (CH

4), protoxide nitrogen (N2O),

hydrofluorocarbons (HFC), perfluorocarbons (PFC) and sulfur hexafluoride (SF

Each of these gases contributes to the greenhouse effect with a different

weight (called GWP or Global Warming Potential).

The measurement of all these gases that also takes account

of their specific GWP is called CO

2 equivalent (CO2eq).

WHAT IS CO2 EQUIVALENT

Cover, knob and plastic elements are available in white and anthracite grey colours

Detector

Covers VI plastic

elements

BM plastic

elements

A mount B mount

• Use the selector placed on the front to turn on or off the device:

- position : device off, no regulation0

- position |: device switched on, active regulation.

• Use the knob to set the intervention value.

It’s possible to set values between 400 ppm and 2000 ppm.

When the CO2 concentration present in the room exceeds the set value,

the red led lights up and the relay switches between contacts 1-2.

Note: in order to preserve the life of the system, the minimum time

between a relay switching and the next one is 1 minute. However, the led

status updating is immediate. Therefore, after using the regulation knob, it

is possible to find a momentary discrepancy between what is indicated by

the led and the actual status of the relay.

This condition lasts for up to 1 minute.

Setpoint modification

The device signals the probe error condition with the LED flashing.

In this case the regulation is inhibited and the relay contact remains

between terminals 2 and 3. Contact Vemer Technical Support.

Probe error signal

AIR mount

COM

NO NC

N L

230Va

1 2 3 4 5

• Install the device at a height of about 1.5-2 m from the floor, avoiding positions

with excess or total lack of ventilation. Also make sure that the detector is

installed away from direct radiation, at a distance of at least 30 centimeters

from doors, windows and heat sources. Pay attention that the flow of air that

hits the detector is not obstructed by curtains or wardrobes placed nearby.

Avoid installing the detector in a humid area or with temperatures outside

the operating range. Also avoid positioning the detector near sinks, hobs

or near extractor hoods or vents and, more generally, areas where dirt

and dust could obstruct the slots, preventing correct operation

• The device is sold already mounted with anthracite colour.

To transform it in the white version, remove the knob and the cover, acting

on the hooks placed on the upper and lower side of the device and mount

the cover and the white knob included in the package.

• Make the connections by respecting

the diagrams described in this manual.

• Fix the device inside the 3 modules box

in compliance with the assembly diagrams

described on the back of this instruction sheet.

The accessories for the installation

included in the package allow the mounting

of the plates described in the diagram

“adjustable cover plates”.

INSTALLATION

Reduction of the adjustment range

It is possible to mechanically limit the adjustment range if the device

is installed, for example, in public places or in hotel rooms.

To limit the adjustment range, proceed as follows:

- position the knob in an intermediate value to the desired range

(for example, if the desired adjustment range is 1000-1600 ppm,

bring the knob indicator to the 1300 ppm position)

- remove the knob.

- under the knob there are two rings marked from the words “min”

and “MAX”, respectively for the lower limit and above.

- turn the “min” ring nut clockwise

and position it at the minimum

value of the desired adjustment

range (refer to the ppm values

shown on the cover).

- turn the “MAX” ring nut

anticlockwise and position

it corresponding to the

maximum value of the

desired adjustment range

(refer to the ppm values shown on the cover).

- reposition the knob, making sure that the indicator of the setpoint on

the knob is in the same position as when the knob has been removed.

To remove the setpoint limitation, turn the two ring nuts until the limitation

blocks are in an external position in the range 400 ppm ÷ 2000 ppm.

REFERENCE STANDARDS

Compliance with Community Directives

2014/35/UE (LVD) and 2014/30/UE (EMCD)

is declared with reference to the following harmonized standards: • EN 60730-2-15

03-2021

Fiuto does not require any particular maintenance.

However, it is necessary to ensure the cleanliness of the slots placed

on the front to ensure proper air flow. Do not use chemicals, polishes

or bleach for cleaning. Simply dust with a damp cloth.

CARE AND MAINTENANCE

After powering up, the device performs the starting phase, which is

necessary to warm up the detector. In this phase, which lasts a total of about

20 seconds, the red led flashes and in the initial 2 seconds the relay switches

twice. In this phase the device does not perform any adjustment and the relay

remains between terminals 2 and 3.

After the starting phase, the device performs the detector self-calibration.

This phase has a variable duration, from about 30 minutes in the best case

(which occurs if the room is well ventilated, with a CO

2eq concentration of

about 400 ppm) up to 8 hours in the worst case. During the self-calibration

phase, the adjustment is still active, even if the CO

2eq measurement carried

out by the detector can take place with lower accuracy.

Note: the starting and self-calibration phase are performed every time

the device is powered.

Start up

Produkt Specifikationer

Mærke:	Vemer
Kategori:	Detektor
Model:	Fiuto

Har du brug for hjælp?

Hvis du har brug for hjælp til Vemer Fiuto stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Detektor Vemer Manualer

Vemer Fiuto Manual

21 April 2024

Detektor Manualer

Nyeste Detektor Manualer

Protector WA-5.1 Manual

21 December 2024

Steinberg SBS-MD-9 Manual

16 December 2024

Steinberg SBS-MD-7 Manual

16 December 2024

Steinberg SBS-MD-2 Manual

16 December 2024

Steinberg SBS-MD-5 Manual

16 December 2024

AstralPool RolaChem RP9 Manual

15 December 2024

Steinberg SBS-MD-3 Manual

15 December 2024

Steinberg SBS-MD-13 Manual

15 December 2024

Steinberg SBS-MD-6 Manual

15 December 2024

Perel EFL27 Manual

14 December 2024