Vemer Sensor 140 Blister Manual

Vemer Bevægelsesdetektor Sensor 140 Blister

Læs nedenfor 📖 manual på dansk for Vemer Sensor 140 Blister (1 sider) i kategorien Bevægelsesdetektor. Denne guide var nyttig for 10 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/1
ISCOM017-0911
Mod. Sensor-140
Sensor-200
User manual
Movement detectors
Read all instructions carefully
The
Sensor-140
and
Sensor-200
proximityswitchesareelectronicswitchingdevices
containingmicro-disconnection(µ)accordingtoEN60669-2-1.Theoutputcircuitisactivated
whenaheatsourcemovesinfrontofthedeviceandisdeactivatedwhennomovementis
intercepted, after a settable period of elapsed time.
SAFETY WARNINGS
During installation and operation of the instrument, comply with the following
instructions:
1) The instrument must be installed by a skilled person, in strict compliance with the
connection diagrams
2) Do not power on or connect the instrument if any part of it is damaged
3) In the building where the instrument is to be installed, there must be a switch and a
device for protection from overloads
4) Before touching the connector terminals make sure that the wires to be connected or
already connected to the instrument are not live.
Code Model Description
VE212700 Sensor-140 Movement detector 140°
VE213500 Sensor-200 Movement detector 200°
TECHNICAL CHARACTERISTICS
• Powersupply:230VAC50Hz
• Beakingcapacity:5A250VAC(resistiveload)
• Maximumrecommendedloads:
 −Incandescentlightbulbs:1000W
 −Non-compensateduorescent:500W
 −Compensateduorescent:250W
 −Halogen(230VAC):1000W
 −Lowconsumptionbulbs:200W
• Consumption:6VA(1W)
• Rangeofbrightness:5-30-2000lux
• Interventiontime:from3secondsto30minutes(approximate)
• Angleofdetection: −Sensor-140:140°
  −Sensor-200:200°
• Rangeofdetection:−frontal12mat20°C
  −lateral8mat20°C
• Operatingtemperature:-20°C÷+40°C
• Protectiondegree:IP55
• Insulation:classII
INSTALLATION
• Thedevicemustbeinstalledfarfrominductiveloads(motors,transformers,telephone
antennas,transformerplants,industrialmachinery,etc.)asespeciallystrongmagnetic
eldsmayalteroperation.Thedevicemustalsobeprotectedfromrainandsunlight.
Itmustnotbeplacednearlights,neardevicesthataresubjecttotemperaturechanges
(heating,airconditioning).Itmustbelocatedfarfromhighlyreectivesurfaces.
 Removethecoverbylooseningthescrewatthebottom.Fastenthebasecoveratthepoint
onthewallwhereyouwanttoinstallit,ataheightof2-3metres.
 Thedirectionofmovementoftheheatsourcemustbetransversaltolensofthedevice,
becausedetectionoccursbymeansofintersectionofbands.Therefore,ifsourcemoves
paralleltothebands,detectionwilloccuratalesserdistance.Theambienttemperature
alsoaffectsthesensitivityofthedevice.Thehigherthetemperature,thepoorersensitivity
willbe.
• Theheadcanrotatehorizontallyabout180°andverticallyabout45°.Toadjusttheeldof
detection:
−turntheinterventiontimeselectortotheminimumandthebrightnessselectorto( );
 −checkcoveragebymovinginsidetheeldofdetection.
 Thedeviceisalsoequippedwithlimitersofthedetectionareadividedintofoursectors.If
appliedtothelens,theymakeitpossibletoexcludeoneormoreofthesectorsoftheeld
of detection.
• Toadjustthebrightness,turntheselectortowards( );whentheambientbrightnessisas
desiredforoperation,startturningtheselectortheotherway,untililluminationoccurs.
• Toadjusttheinterventiontime,turntheselector() to the desired position. You can
choosefromaminimumof3secondstoamaximumof30minutes.Thistimeisreset
eachtimethereisaninterceptionbythedetector.
• Duringnormaloperation,whenthelevelofbrightnessdropsbelowthesetlevel,the
devicesetsupfordetection,andsignalsthisconditionviaashingoftheinternalLED.
OPERATION
• The
Sensor-140
and
Sensor-200
havetwooperatingmodes:
 −normalmode,inwhichthedevicesarenormallyactivated30secondsaftertheyare
connected;
 −permanentlyon,withthedevicesremainingonpermanentlyforsixhours.Thisoccurs
whenyouperformarapidOFF-ON-OFF-ONoperation(lessthan2seconds).The
devicesbeingoperatinginnormalmodeagainwhenthesixhourshaveelapsedorif,
duringthisperiod,youperformanotherOFF-ONoperation.
REFERENCE STANDARDS
ConformitytotheEUdirectives:
2006/95/EC(lowvoltage)
2004/108/CE(EMC)
isdeclaredwithreferencetoharmonizedstandard:
EN 60669-2-1
Dimensions
Connection diagrams
Sensitivity
L' N L
L
N
L' N L
230 V ACLAMPADINA
µ
10072
80
GREATER SENSITIVITY LESS SENSITIVITY
BULB
direction of
movement
direction of
movement
Field of detection

Produkt Specifikationer

Mærke: Vemer
Kategori: Bevægelsesdetektor
Model: Sensor 140 Blister

Har du brug for hjælp?

Hvis du har brug for hjælp til Vemer Sensor 140 Blister stil et spørgsmål nedenfor, og andre brugere vil svare dig


Bevægelsesdetektor Vemer Manualer

Vemer

Vemer Sensor 140 Manual

28 Oktober 2023
Vemer

Vemer Sensor 200 Manual

19 September 2023
Vemer

Vemer Sensor 140 Blister Manual

31 August 2023
Vemer

Vemer Sensor HF Manual

1 Februar 2023
Vemer

Vemer Sensor-360 Manual

23 December 2022
Vemer

Vemer Sensor-2T Manual

4 November 2022
Vemer

Vemer Sensor-T Manual

14 Oktober 2022

Bevægelsesdetektor Manualer

Nyeste Bevægelsesdetektor Manualer

XQ-lite

XQ-lite XQ0927 Manual

11 Juni 2024
XQ-lite

XQ-lite XQ0928 Manual

10 Juni 2024
CnMemory

CnMemory i.onik WS-103 Manual

7 Juni 2024
Steren

Steren LAM-071 Manual

5 Juni 2024
Steren

Steren LAM-055 Manual

5 Juni 2024
Steren

Steren ALA-034 Manual

5 Juni 2024
Steren

Steren ALA-036 Manual

5 Juni 2024
Esylux

Esylux MD-FLAT 360i/8 Manual

17 Maj 2024
EQ-3

EQ-3 HmIP-SMI Manual

17 Maj 2024
ORNO

ORNO OR-CR-243 Manual

11 Maj 2024