Ventus W636 Manual

Ventus Vejrstation W636

Læs nedenfor 📖 manual på dansk for Ventus W636 (2 sider) i kategorien Vejrstation. Denne guide var nyttig for 24 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

KSPO:1719-10

NIL TE636NL & TS21 MANUAL 2(ENG)

SIZE:W105 X H148(mm)

BY Lai HZ 9/3/11

SLIM WEATHER FORECASTER WITH

RADIO CONTROLLED CLOCK,

PRESSURE DISPLAY AND IN/ OUT

THERMO-HYGROMETER

USER MANUAL

(TE636NL)

INTRODUCTION

Thank you for selecting our slim Weather Forecaster. This device combines precise time

keeping, monitoring and displaying of pressure information and current temperature/ humidity

data from up to three remote locations (additional sensors are required).

In this package, you will ﬁnd:

• One main unit (receiver)

• One single-channel remote sensor (transmitter)

• One user manual

Please keep this manual handy as it contains practical instructions, technical speciﬁcations and

precautions.

INSTALLATION

The communication between the main unit (receiver) and the remote sensor (transmitter) is

wireless, thus simplifying the installation. The remote temperature sensor transmits data to the

main unit, with an operating range of up to 30 meters in opened area.

The remote temperature sensor can be placed indoors or outdoors, depending on the area where

the temperature is intended to be measured. If you intend to measure outdoor conditions, place

the remote sensor outdoors.

NOTE:

• It is critical to power the remote sensor setting up the main unit.BEFORE

• It is critical to power up and communication between the remote sensor and the main unit test

permanently mounting if outside.BEFORE

BEFORE YOU BEGIN

• We recommend using for the remote sensor and the main unit. When the alkaline batteries

temperature falls below freezing point 0°C (32°F), battery voltage levels will be dropped and

this may reduce the transmission range. For optimum performance, we recommend using

lithium batteries.

• Avoid using rechargeable batteries. (Rechargeable batteries cannot maintain correct power

requirements.)

• ALWAYS remote install batteries in the sensor the main unit. before

• Insert batteries before ﬁrst use, matching the polarity in the battery compartment.

• During initial set up, place the remote sensor close to the main unit.

• After reception is established (remote readings will appear on the main unit’s display),

position the remote sensor and the main unit within the eﬀective transmission range of up to

30 meters.

NOTE:

• Avoid pressing any buttons on the main unit before the remote readings are displayed.

• Transmission or reception range may be aﬀected by trees, metal structures, and electronic

appliances, surrounding building materials and how the main unit and transmitter are

positioned.

• Place the remote sensor so that it faces the main unit (receiver), minimizing obstructions

such as doors, walls and furniture.

• Though the remote sensors are weather-resistant, they should be placed away from direct

sunlight, rain or snow. The optimal location for the remote sensor outdoors is under the eaves

on the north side of the building.

REMOTE TEMPERATURE AND HUMIDITY SENSOR

FEATURES

• Remote data transmission to the main unit via 433 MHz frequency

A. BATTERY COMPARTMENT

• Hold two AAA-size batteries

B. WALL-MOUNT RECESSED HOLE

• Mount the remote sensor on the wall

MOUNTING

• The remote sensor can be placed on the ﬂat surface or mounted on the wall in vertical

position.

• Use a screw, rather than a nail, for best mounting of the sensor.

• When mounting the main unit on the wall or vertical surface, fold the table stand back into

the unit.

PLACEMENT

• The remote sensor should be placed under eaves or a similar location with free air circulation

sheltered from direct sunlight and extreme weather.

• Ideally, place the remote sensor over soil, rather than asphalt which would cause false

readings.

• Avoid placing the remote sensor near sources of heat, such as chimneys and heating elements

• Avoid areas that collect heat from the sun and radiate heat, such as metal, brick or concrete

structures, paving, and patios

• The international standard for the valid air temperature measurements is 1.25meters above the

ground

OPERATION

Immediately after batteries are installed, the remote sensor will start transmitting a temperature

and humidity data to the main unit.

A B

MAIN UNIT

FEATURES

TIME

• Precise time and date set via radio controlled time signals (DCF 77) from the central atomic

clock in Frankfurt

• 12 or 24 hour time format

• Manual adjustment of time and date

• Calendar date with month and day in 7 languages English, German, French, Italian, Spanish,

Dutch and Swedish

• Dual crescendo alarms with snooze

• Programmable ice warning alarm

WEATHER

• Weather forecast for the next 12 to 24 hour in seven large icons: sunny, slightly cloudy,

cloudy, rainy, heavy rainy, snowy and heavy snowy.

• User-deﬁned high/low temperature alarm

• Indoor/outdoor temperature and humidity in up to 3 remote locations (additional sensors

required)

• Barometric pressure in imperial or metric units

• Altitude adjustment for pressure compensation

• 24 hour barometric pressure history chart

• Comfort level indicators (Dry, Humid, etc)

FRONT

REAR

A. WEATHER/ PRESSURE window

B. TEMPERATURE/ HUMIDITY window

C. CLOCK window

D. DOWN ( ) button ▼

• Select the next available mode

• Press and hold for 2 seconds to search for wireless signal from remote sensor.

• Decrease parameters.

E. ALARM button

• When time mode has been selected, press once to display the alarm time of weekday alarm

( ), single alarm ( ) and pre-alarm ( ).

• Hold for 2 seconds, set weekday, single or pre-alarm’s alarm time.

• When temperature mode has been selected, press once to display the highest or lowest

temperature alarm’s value.

• Hold for 2 seconds, set the highest or lowest temperature alarm’s value.

• When alarm is on, press once to stop the alarm temporarily.

F. CHANNEL button

• Press to display the outdoor temperature readings of Channels 1, 2 and 3. (additional remote

sensors are required)

• Hold for 2 seconds, enter into the circulation mode and outdoor temperature readings of

Channels 1, 2 and 3 will be displayed automatically in every 5 seconds.

G. MODE button

• When pressure mode has been selected, press once to display the local pressure, altitude and

sea level.

• Press and hold for 2 seconds to set altitude and sea level.

• When time mode has been selected, press once to toggle between time with seconds display

or time with weekday display.

• Press and hold for 2 seconds, set language of the day of the week, year digit, month digit,

date digit, hour format (12/ 24 hours), hour digit and minute digit. (Note: calendar format is

default in month-date display)

• When temperature mode has been selected, press and hold for 2 seconds to toggle the

temperature unit between Celsius or Fahrenheit.

H. UP ( ) button▲

• Press to select the next available mode

• Increase the parameters

• In time with seconds display mode, press and hold for 2 seconds to activate/ deactivate radio

controlled time signal search manually.

I. MEM button

• When temperature mode has been selected, press to recall the minimum or maximum

temperature and humidity readings of main and remote units.

• Press and hold for 2 seconds, collected memories will be cleared.

• When pressure mode has been selected, press once to check the historical pressure data for

the past 24 hours.

J. WALL- MOUNT hole

• A recessed opening to mount the unit on a wall

K. BATTERY COMPARTMENT

• Accommodate two (2) CR2032 batteries

L. TABLE STAND

PLACEMENT

• Make sure that the main unit is locating within the operating range of all remote sensors.

• Ideally the main unit should be placed within line of sight of remote sensors. Avoid

placing the main unit where surfaces emitting and radiating heat (e.g. heating ducts or air

conditioners) and areas with interference from wireless devices (e.g. cordless phones, radio

headsets, baby monitoring devices and other electronics).

OPERATION

Once the main unit is powered, the display will show all available LCD segments for a moment.

IMPORTANT: All of the display functions will be locked, allowing setting your local altitude

and pressure parameters by pressing the UP ( ) DOWN ( ) MODE▲ or ▼ and buttons. The

locked display will show the pressure icon and abbreviation ﬂashing in the “inHg” Weather/

Pressure Window Clock Window, default time in and channel 1’s temperature and humidity

readings in Temperature/ Humidity Window.

If pressure and altitude are not conﬁgured during this time, the unit will self-calibrate in a few

minutes and show the default settings for the pressure and altitude (sea level) and all remote

weather sensors readings.

IFE

17 18

19 20

21 22

Produkt Specifikationer

Mærke:	Ventus
Kategori:	Vejrstation
Model:	W636

Har du brug for hjælp?

Hvis du har brug for hjælp til Ventus W636 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Vejrstation Ventus Manualer

21 December 2024

31 August 2024

31 August 2024

31 August 2024

31 August 2024

17 August 2024

8 Juli 2024

8 Juli 2024

8 Juli 2024

8 Juli 2024

Vejrstation Manualer

Nyeste Vejrstation Manualer

Steinberg SBS-WS-500 Manual

18 December 2024

EQ-3 WDC 7000 Manual

16 December 2024

Steinberg SBS-RS-40 Manual

16 December 2024

Sencor SWS 260 Manual

15 December 2024

Steinberg SBS-WS-600 Manual

15 December 2024

ADE WS 2136-1 Manual

15 December 2024

TFA 30.3034.01 Manual

14 December 2024

TFA Weather Boy 35.1159.02 Manual

14 December 2024

TFA 35.1078.10 Manual

14 December 2024

TFA 35.1089 Manual

14 December 2024