Vivanco UR 82 SE Manual
Vivanco
Fjernbetjeninger
UR 82 SE
Læs nedenfor 📖 manual på dansk for Vivanco UR 82 SE (23 sider) i kategorien Fjernbetjeninger. Denne guide var nyttig for 7 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/23
UR Universal Controller
Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, e-Mail: 1hotline@vivanco.de
( GB ) Operating Instructions -> 1
( D ) Bedienungsanleitung -> 2
( F ) Notice d'emploi -> 3
( E ) Instrucciones de uso ->5
( I ) Istruzioni per l’uso->6
( NL ) Gebruiksaanwijzing -> 8
( PL ) Instrukcja obsługi -> 9
( P ) Instruções de operação -> 10
(DK) Betjeningsvejledning -> 12
(S) Bruksanvisning -> 13
(RUS) ->14 Руководство по эксплуатации
(GR) ->16 Οδηγίες χρήσης
(TR)
Kullanma talimatı -> 18
(CZ)
Návod k obsluze -> 19
(SK) Návod na obsluhu-> 20
(H) Kezelési utasítása -> 22
(GB) Instructions
Inserting the batteries
Open the battery flap on the back of the remote
control, press the tongue lightly downwards,
then insert 2 alkaline AAA batteries. Check that
the polarity markings on the batteries and in the
battery compartment are correctly lined up
(+=+), then close the flap carefully. – Always
use undamaged batteries.
Adapting to a device (e.g. TV or DVB Set
Top Box (or SAT/Cable) etc.
In order to control e.g. your TV or DVB you
must adapt or set the remote control to it. There
are two ways of doing so: direct control code
entry or code search.
If your does not understand you it blinks UR
and you can then repeat the entry. Each
understood entry is confirmed by LED blinking
briefly.
Direct control code entry using the enclosed
list
Example: setting to control a Panasonic
television set:
1. The enclosed list gives, for example, the
Panasonic Code . 153
2. To prepare code entry, briefly press the
SET TV button, and then the -button, until the
Powerkey lamp/LED lights constantly.
3. Then press the number buttons (e.g. 1 5
3) in sequence.
4. Once the numbers have been entered the
button lamp goes out and the remote control is
ready to control your appliance.
5. Finally, test the control code setting by
trying to control your television set. If it does not
work at all or not correctly try a different code
from the list or the code search (see below).
Code search
If the brand of your appliance is not in the list or
none of the codes given fits, we recommend a
code search.
Manual code search
1. Switch on the appliance to be controlled.
Program is running.
2. To prepare the code search, briefly press
the button and then additionally a SET
appliance button, e.g. the button, TV or DVB
until the lamp (LED) lights constantly.
3. Then point the remote control at the
appliance to be controlled.
4. ON/OFF Briefly press the
(appliance on/off) button once. The lamp (LED)
blinks.
5. ON/OFF Press the (appliance
on/off) button repeatedly, approx. every second,
until appliance, reacts. - If you notice the
reaction of your appliance too late and the next
code has already been emitted you can go back
by pressing and then again. If SET ON/OFF
your appliance has switched itself off you must
switch it back on again, e.g. on the appliance or
with the original remote control, to continue
searching. - When your appliance reacts you
can also try out other buttons without
interrupting the search. If some buttons do not
work properly, simply continue searching with
ON/OFF.
6. When your appliance reacts correctly,
press the appliance button e.g. and end the TV
search. The lamp (LED) goes out.
- The search stops after approx. 30 seconds of
inactivity.
Automatic code search
Your remote control finds the correct settings
almost automatically in seconds:
1. Switch on the appliance to be controlled
so that you can watch a TV program.
2. To start the code search, press the SET
button, and then additionally the appliance
button e.g. for more than 3 TV or DVB,
seconds until the -key lamp (LED) starts Power
to blink.
3. Then point the remote control at the
appliance to be controlled while the remote
control emits a different signal every 2 ON/OFF
seconds.
4. When your appliance reacts, press any
button, except , to end the search. – SET If you
ended the search too late, continue to search
using the (see above).Manual Code Search
5. Finally, test the control code setting by
trying to control your appliance. If it does not
work correctly, please try the code search
again. The code search then begins with the
next code in the sequence. - Remember to
switch your appliance back on again if you wish
to continue searching.
Produkt Specifikationer
| Mærke: | Vivanco |
| Kategori: | Fjernbetjeninger |
| Model: | UR 82 SE |
Har du brug for hjælp?
Hvis du har brug for hjælp til Vivanco UR 82 SE stil et spørgsmål nedenfor, og andre brugere vil svare dig
Fjernbetjeninger Vivanco Manualer
13 Juli 2024
9 Juli 2024
5 Oktober 2022
5 Oktober 2022
5 Oktober 2022
5 Oktober 2022
5 Oktober 2022
5 Oktober 2022
5 Oktober 2022
Fjernbetjeninger Manualer
- Fjernbetjeninger SilverCrest
- Fjernbetjeninger Philips
- Fjernbetjeninger LG
- Fjernbetjeninger Logitech
- Fjernbetjeninger One For All
- Fjernbetjeninger Hama
- Fjernbetjeninger Thomson
- Fjernbetjeninger Hannspree
- Fjernbetjeninger T'nB
- Fjernbetjeninger Medion
- Fjernbetjeninger Sweex
- Fjernbetjeninger König
- Fjernbetjeninger Meliconi
- Fjernbetjeninger Bang And Olufsen
- Fjernbetjeninger Ruwido
- Fjernbetjeninger Telefunken
- Fjernbetjeninger Technics
- Fjernbetjeninger Tevion
Nyeste Fjernbetjeninger Manualer
14 Oktober 2024
13 Oktober 2024
13 Oktober 2024
12 Oktober 2024
11 Oktober 2024
11 Oktober 2024
10 Oktober 2024
9 Oktober 2024
9 Oktober 2024
8 Oktober 2024