Vivanco UR 81 Manual
Vivanco
Fjernbetjeninger
UR 81
Læs nedenfor 📖 manual på dansk for Vivanco UR 81 (35 sider) i kategorien Fjernbetjeninger. Denne guide var nyttig for 6 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/35
UR81 Universal Controller
Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, e-Mail: 1hotline@vivanco.de
( GB ) Operating Instructions -> 1
( D ) Bedienungsanleitung -> 2
( F ) Notice d'emploi -> 3
( E ) Instrucciones de uso -> 4
( I ) Istruzioni per l’uso->6
( NL ) Gebruiksaanwijzing -> 7
( PL ) Instrukcja obsługi -> 8
( P ) Instruções de operação -> 9
(DK) Betjeningsvejledning -> 11
(S) Bruksanvisning -> 12
(RUS)
->
13
(GR) ->15
(TR)
Kullanma talimatı -> 16
(CZ)
Návod k obsluze -> 17
(SK) Návod na obsluhu-> 18
(H) Kezelési utasítása -> 20
(GB) Instructions
Inserting the batteries
Open the battery flap on the back of the
remote control, press the tongue lightly
downwards, then insert 2 alkaline AAA
batteries. Check that the polarity markings on
the batteries and in the battery compartment
are correctly lined up (+=+), then close the flap
carefully. – Always use undamaged batteries.
Adapting to a device (e.g. TV or DVB Set
Top Box (or SAT/Cable) etc.
In order to control e.g. your TV or DVB you
must adapt or set the remote control to it.
There are two ways of doing so: direct control
code entry or code search.
If your UR81 does not understand you it blinks
and you can then repeat the entry. Each
understood entry is confirmed by LED blinking
briefly.
Direct control code entry using the
enclosed list
Example: setting to control a Panasonic
television set:
1. The enclosed list gives, for example, the
Panasonic Code . 153
2. To prepare code entry, briefly press the
SET TV button, and then the -button, until the
Powerkey lamp/LED lights constantly.
3. Then press the number buttons (e.g. 1 5 3)
in sequence.
4. Once the numbers have been entered the
button lamp goes out and the remote control is
ready to control your appliance.
5. Finally, test the control code setting by
trying to control your television set. If it does
not work at all or not correctly try a different
code from the list or the code search (see
below).
Code search
If the brand of your appliance is not in the list
or none of the codes given fits, we recommend
a code search.
Manual code search
1. Switch on the appliance to be controlled.
Program is running.
2. To prepare the code search, briefly press
the button and then additionally a SET
appliance button, e.g. the button, TV or DVB
until the lamp (LED) lights constantly.
3. Then point the remote control at the
appliance to be controlled.
4. ON/OFF Briefly press the (appliance
on/off) button once. The lamp (LED) blinks.
5. ON/OFF Press the (appliance on/off)
button repeatedly, approx. every second, until
appliance, reacts. - If you notice the reaction of
your appliance too late and the next code has
already been emitted you can go back by
pressing and then again. If your SET ON/OFF
appliance has switched itself off you must
switch it back on again, e.g. on the appliance
or with the original remote control, to continue
searching. - When your appliance reacts you
can also try out other buttons without
interrupting the search. If some buttons do not
work properly, simply continue searching with
ON/OFF.
6. When your appliance reacts correctly,
press the appliance button e.g. and end the TV
search. The lamp (LED) goes out.
- The search stops after approx. 30 seconds of
inactivity.
Automatic code search
Your remote control finds the correct settings
almost automatically in seconds:
1. Switch on the appliance to be controlled so
that you can watch a TV program.
2. To start the code search, press the SET
button, and then additionally the appliance
button e.g. for more than 3 TV or DVB,
seconds until the -key lamp (LED) starts Power
to blink.
3. Then point the remote control at the
appliance to be controlled while the remote
control emits a different signal every ON/OFF
2 seconds.
4. When your appliance reacts, press any
button, except , to end the search. – SET If you
ended the search too late, continue to search
using the (see above).Manual Code Search
5. Finally, test the control code setting by
trying to control your appliance. If it does not
work correctly, please try the code search
again. The code search then begins with the
next code in the sequence. - Remember to
switch your appliance back on again if you
wish to continue searching.
Code identification
You can read off the 3-digit codes you have
set at any time:
1. Press the appliance button of the appliance
whose code you want to read off, e.g. .TV
2. SET Press the button and additionally , 1 2
or , depending on the part of the code you 3
want to read off. For example, if you press
SET+1 153 and the code (in this example) has
been set, the lamp blinks once after is SET+1
released to show that the hundred figure is 1.
All you have to do is count. The ten figure is
indicated after is released, e.g. it blinks SET+2
5 times for the 5 in 1 3. The one figure is 5
Produkt Specifikationer
| Mærke: | Vivanco |
| Kategori: | Fjernbetjeninger |
| Model: | UR 81 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Vivanco UR 81 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Fjernbetjeninger Vivanco Manualer
13 Juli 2024
9 Juli 2024
5 Oktober 2022
5 Oktober 2022
5 Oktober 2022
5 Oktober 2022
5 Oktober 2022
5 Oktober 2022
5 Oktober 2022
Fjernbetjeninger Manualer
- Fjernbetjeninger SilverCrest
- Fjernbetjeninger Philips
- Fjernbetjeninger LG
- Fjernbetjeninger Logitech
- Fjernbetjeninger One For All
- Fjernbetjeninger Hama
- Fjernbetjeninger Thomson
- Fjernbetjeninger Hannspree
- Fjernbetjeninger T'nB
- Fjernbetjeninger Medion
- Fjernbetjeninger Sweex
- Fjernbetjeninger König
- Fjernbetjeninger Meliconi
- Fjernbetjeninger Bang And Olufsen
- Fjernbetjeninger Ruwido
- Fjernbetjeninger Telefunken
- Fjernbetjeninger Technics
- Fjernbetjeninger Tevion
Nyeste Fjernbetjeninger Manualer
14 Oktober 2024
13 Oktober 2024
13 Oktober 2024
12 Oktober 2024
11 Oktober 2024
11 Oktober 2024
10 Oktober 2024
9 Oktober 2024
9 Oktober 2024
8 Oktober 2024