Vtech DM1211 Manual

Vtech Babyalarm DM1211

Læs nedenfor 📖 manual på dansk for Vtech DM1211 (4 sider) i kategorien Babyalarm. Denne guide var nyttig for 34 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/4

Caution

• The default volume of your parent unit is . If you experience high-pitched screeching noise from level 3

your baby monitor :while positioning

- Make sure your baby unit and parent unit are more than apart, OR

6.5 feet (2 meters)

- Turn down the volume of your parent unit.

Operating range

The operating range of the baby monitor is up to 1,500 feet (450 meters) outdoors or 160 feet

(50 meters) indoors. The actual operating range may vary depending on the environmental

conditions, and other interferences such as walls, doors, and other obstructions.

Install the parent unit battery

The parent unit runs on rechargeable battery or AC power. To continuously monitor your

baby, make sure you use both battery and AC power at the same time. With the battery

alone, the parent unit can cordlessly run for a short time only.

NOTESNOTE

• Use only the battery supplied with this product.

• If the parent unit will not be used for a long time, disconnect and remove the battery to prevent possible leakage.

Replace the battery

To replace the battery, unplug the battery connector from the socket, and then pull the

battery out of the battery compartment. Follow the steps above to install the battery.

Connect the baby monitor

When you have connected and turned on the baby unit and all the parent units, they will

enter pairing mode automatically. It takes around 10 minutes for the pairing process to

complete. When the parent unit and baby unit are successfully paired, both their power

LEDs are on steadily. The baby monitor is ready to use.

NOTESNOTE

• Use only the power adapters supplied with this product.

• Make sure the baby monitor is not connected to a switch-controlled electric outlet.

• Connect the power adapters in a vertical or ﬂoor mount position only. The adapters’ prongs are not

designed to hold the weight of baby monitor, so do not connect them to any ceiling, under-the-table,

or cabinet outlets. Otherwise, the adapters may not properly connect to the outlets.

• Make sure the parent unit, the baby unit and the power adapter cords are out of reach of children.

• With audio reminder feature preset to , the parent unit plays an audio reminder when it is ON

connected to a baby unit.

Charge the parent unit battery

When you have connected the parent unit and installed its battery for the ﬁrst time or after

power outage, the parent unit powers on automatically. The battery icon indicates the

battery status (see the following table).

1 set for DM1211;

2 sets for DM1211-2

User’s manual

DM1211

DM1211-2

Enhanced Range

Digital Audio Monitor

Go to www.vtechphones.com

to register your product for enhanced

warranty support and the latest VTech

product news.

Congratulations

on purchasing your new VTech product. Before using this product, please read Important safety

instructions.

This manual has all the feature operations and troubleshooting necessary to install and operate

your new VTech product. Please review this manual thoroughly to ensure proper installation and

operation of this innovative and feature-rich VTech product.

For support, shopping, and everything new at VTech, visit our website at www.vtechphones.com.

What’s in the box

Connect and charge the battery

Notes

• The parent unit battery is fully charged after 3 hours of continuous charging.

• It takes longer to charge the battery when the parent unit is turned on. To shorten the charging time,

turn the parent unit off while charging.

• The standby time varies depending on the sensitivity level you set, your actual use and the age of the battery.

Battery indicators Battery status Action

The battery icon is off. No battery is installed but

operates using AC power.

Install the parent unit battery.

Charge without interruption (at least

30 minutes).

The screen displays LOW

BATTERY and . The light

flashes.

The battery has very little

charge and may be used

for only a short time.

Charge

without interruption

(about

30 minutes).

The battery icon becomes

solid .

The battery is fully charged. To keep the battery charged, connect

it to AC power when not in use.

THIS SIDE UP

AVERTISSEMENT :

THIS S IDE UP / CE CÔTÉ VER S LE HAUT

AVERT ISS EMEN T :

THIS S IDE UP / CE CÔ TÉ VERS LE HAUT

Note

Make sure the label

THIS SIDE UP is facing

up while inserting the

battery.

LINKED

6.5ft (2m)

Note

• This baby monitor is intended as an aid. It is not a substitute for proper adult supervision, and should not be used

as such.

Test your audio monitor

You may test the baby monitor before initial use, and at regular times thereafter.

Caution

• For hearing protection, make sure the parent unit is more than 6.5

feet (2 meters) away from the baby unit. If you hear any

high-pitched noise, move the parent unit further until the noise

stops. You can also press on the parent unit to lower or mute

the noise.

1. Make sure your baby unit and parent unit are on.

2. Speak towards the microphone of the baby unit. You will

hear the sound at the parent unit, and see the visual sound

indicators light up.

Note

• When the parent unit displays and , move the parent unit closer to the baby NOT LINKED ﬂashes

unit (observe the minimum distance of 6.5 feet/ 2 meters). You can also check if the baby monitor is

connected to a live power socket and switched on.

Tip

• Increase the speaker volume of the parent unit if you cannot hear the sounds transmitted from the baby

unit.

Positioning the baby monitor

Caution

• Keep the baby units out of the reach of baby. Never place or mount the baby units inside the your

baby’s crib or playpen.

1. Place the baby units more than 3 feet (1 meter) away from your baby.

2. Place the parent unit more than 6.5 feet (2 meters) away from the baby unit to avoid

screeching noise.

Before use

> 3ft (1m)

LINKED

> 6.5ft (2m)

6.5ft (2m)

3 Using the baby monitor

Power on or off the baby unit

• Press to power on the baby unit. The .

power light turns on

• Press and hold to power off the baby unit. The power light

turns off.

Power on or off the parent unit

• Press and hold to power on the parent unit. The screen turns on.

• Press and hold again to power off the parent unit. The screen

turns off.

Note

• The parent unit powers on automatically once it is connected to power

socket or battery installed. The baby unit also powers on automatically once

connected to power socket.

Adjust the speaker volume for baby unit

• Press or on the baby unit at any time.

Note

• The speaker of baby unit cannot be muted.

Adjust the speaker volume for parent unit

You can adjust the speaker volume from VOLUME 1 to VOLUME 5, or turn it off. The

speaker volume is preset to .VOLUME 3

• Press or when the parent unit is not in use.

When the speaker volume is set to VOLUME OFF, the screen displays .

Adjust the sound sensitivity of the baby unit

You can choose to hear sounds from the baby unit all the time, or to hear sounds that exceed

a certain level. You can use the parent unit to adjust the microphone sensitivity of your baby

unit. The higher the sensitivity level, the more sensitive the baby unit is in detecting sounds

for transmitting to the parent unit. The VOX sensitivity level is preset to HIGHEST.

VOX

Sensitivity

level

Highest High Medium Low Lowest

Description The parent

unit speaker

is constantly

on, and you

will hear

all sounds

(including

background

noises) from

your baby’s

room.

The parent

unit speaker

turns on for

soft babbling

and louder

sounds from

your baby. It

remains quiet

when your

baby sleeps

soundly.

The parent

unit speaker

turns on

for loud

babbling

and louder

sounds from

your baby. It

remains quiet

when your

baby makes

soft sounds.

The parent

unit speaker

turns on

for crying

and louder

sounds from

your baby. It

remains quiet

when your

baby makes

soft sounds.

The parent

unit speaker

turns on for

loud crying

or screeching

sounds from

your baby. It

remains quiet

when your

baby makes

soft sounds.

1. Press MENU when the parent unit is not in use.

2. Press to select .SELECT VOX LEVEL

3. or to choose the desired sensitivity level.Press

4. Press to conﬁrm your selection. The screen displays and you hear a SELECT SAVED

conﬁrmation tone.

Note

• To enter the menu of the parent unit, the baby unit must be turned on.VOX Level

Sound alert

If you want the parent unit alerts you with sound, especially when the baby unit detects loud

sounds, you can turn on the sound alert feature. This feature is preset to .OFF

Once this feature is on, is shown on LCD display. When the visual sound indicator hits

the red light range, i.e. the baby unit detects loud sounds, your parent unit beeps and

flashes.

1. Press MENU when the parent unit is not in use.

2. Press or to choose SOUND ALERT, then press SELECT.

3. Press or to choose or ON OFF.

4. Press SELECT to conﬁrm your selection. The screen displays and you hear a SAVED

conﬁrmation tone.

Note

• The sound alert setting on each parent unit is independent.

Vibration alert

You can set your parent unit to vibrate and alert you, whenever the baby unit detects loud

sounds. This feature is preset to .OFF

Once this feature is on, is shown on LCD display. When the visual sound indicator hits the

red light range, i.e. the baby unit detects loud sounds, your parent unit vibrates and flashes.

1. Press MENU when the parent unit is not in use.

2. Press or to choose VIBE ALERT, then press .SELECT

3. Press or to choose or ON OFF.

4. Press to conﬁrm your selection. The screen displays and you hear a SELECT SAVED

conﬁrmation tone.

Notes

• Each time you set the vibration alert to , the parent unit vibrates brieﬂy after you press .ON SELECT

• The vibration alert setting on each parent unit is independent.

Nightlight

Both your parent unit(s) and baby unit allow you to turn on or off the nighlight on the baby unit.

Turn on/off the nightlight using the baby unit:

1. Press to turn on the nightlight.

2. Press again to turn off the nightlight.

Turn on/off the nightlight using the parent unit:

1. Press MENU when the parent unit is not in use.

2. Press or to choose NIGHTLIGHT, then press .SELECT

3. Press or to choose or ON OFF.

4. Press to conﬁrm your selection. The screen displays SELECT SAVED and you hear

a conﬁrmation tone.

Notes

• When the nightlight is turned on, the parent unit displays .

• The nightlight on baby unit operates even when the parent unit battery is out of charge or has been turned off.

• If the parent unit lost link, the nightlight icon on its LCD display will disappear, regardless of the nightlight

status.

Language

You can select a language ( , English Spanish or French) to be used in all screen displays. The

language is preset to English.

1. Press MENU when the parent unit is not in use.

2. Press or to choose LANGUAGE, then press SELECT.

3. Press or to choose , , or . ENGLISH ESPANOL FRANCAIS

4. Press to conﬁrm your selection. The screen displays SELECT SAVED and you hear

a conﬁrmation tone.

Note

• The language setting on each parent unit is independent.

Turn on or off the audio reminder

With audio reminder feature preset to , the parent unit plays an audio reminder when ON

it is connected to a baby unit. It reminds you to place the baby unit at least 3 feet (1 meter)

away from your baby, and keep the cords out of the reach of children.

1. Press

when the parent unit is not in use.

2. Press or to choose , then press REMINDER SELECT.

3. Press or to choose or ON OFF.

4. Press to conﬁrm your selection, and you hear a conﬁrmation tone. SELECT

Notes

• You can press or when the parent unit is playing the reminder. to adjust the volume

• If the speaker volume of the parent unit is turned off, it will change to the default volume level when the

parent unit plays the reminder.

Set default

Use this feature to restore to the default settings. Restoring the default settings on one

parent unit will also reset the shared settings for VOX sensitivity level of the other parent unit.

1. Press MENU when the parent unit is not in use.

2. Press or to choose , then press .SET DEFAULT SELECT

3. Press or to choose or .YES NO

4. When you choose , press to conﬁrm your selection. The screen displays YES SELECT

SAVED and you hear a conﬁrmation tone.

-OR-

When you choose NO, press to conﬁrm your selection. The screen displays the SELECT

previous menu.

Talk to the baby unit

You can broadcast messages from a parent unit to the baby unit and the other parent unit. If

you have two parent units, you can use both of them at the same time to talk to the baby unit.

1. Press and hold TALK on the side of the parent unit. The screen displays when the TALK

voice connection to the baby unit is made.

2. Speak towards the on the parent unit. Your voice is broadcast to the baby unit and MIC

the other parent unit.

Notes

• If you have two parent units, and you use one of them to talk to you baby, your voice will broadcast to

both the baby unit and the other parent unit. The other parent unit displays TALKBACK. However, no

sound will transmit from the baby unit to any parent unit during broadcasting.

• If speaker volume of the parent unit has been turned off before the talk, it will change to default

volume level after the talk ﬁnished.

Find/page the parent unit

Use this feature to locate misplaced parent units.

1. Press on the baby unit. All idle parent units ring and display .PAGE PAGING

2. To end paging, press any key on the parent unit, or press on the baby unit.PAGE

Notes

• Paging rings all parent units even if the speaker volume of parent unit is set to VOLUME OFF.

• The baby unit cannot page any parent unit that is turned off, out of range, or talking to the baby unit.

3 Using the baby monitor (Con’t)

Frequency control Crystal controlled PLL synthesizer

Transmit frequency Baby unit: 1921.536-1928.448 MHz

Parent unit: 1921.536-1928.448 MHz

Channels 5

LCD 35 (x) x 21.2 (y) mm B&W LCD

Nominal effective range Maximum power allowed by FCC and IC. Actual operating range may vary

according to environmental conditions at the time of use.

Power requirement Parent unit: 2.4 V Ni-MH battery

Baby unit power adapter:

Output: 6V DC 400mA

Parent unit power adapter:

Output: 6V DC 400mA

Technical speciﬁcations

Speciﬁcations are subject to change without notice.

Document order number: 91-010892-040-100

Produkt Specifikationer

Mærke:	Vtech
Kategori:	Babyalarm
Model:	DM1211
Produktfarve:	Hvid
Batteriteknologi:	Nikkel-Metalhydrid (NiMH)
Indbyggede højttaler(e):	Ja
Højttaler, type:	2-vejs
Strømkilde type:	Batteri
Indbygget mikrofon:	Ja
Grænseflade:	Radio
Strøm-LED:	Ja
Nattilstand:	Ja
Maks. rækkevidde:	75 m
Støjregistrering:	Ja
Temperaturføler:	Ja
Bælteclip:	Ja
Natbelysning:	Ja