Vtech IS8102 Manual

Vtech Telefon IS8102

Læs nedenfor 📖 manual på dansk for Vtech IS8102 (2 sider) i kategorien Telefon. Denne guide var nyttig for 3 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

User’s manual

(Canada version)

Go to www.vtechcanada.com

for latest VTech product news.

Telephones identified with this

logo have reduced noise and

interference when used with most

T-coil equipped hearing aids and

cochlear implants. The TIA-1083

Compliant Logo is a trademark of

the Telecommunications Industry

Association. Used under license.

Compatible with

Hearing Aid T-Coil

TIA-1083

Congratulations

on purchasing your new VTech product. Before

using this telephone, please read

Important safety instructions.

This manual has instructions on how to set up and

using the handset, see the Quick start guide that

came with your telephone base.

You may also view or download the online user’s

manual for a full set of installation and operation

instructions at www.vtechphones.com.

In Canada, visit www.vtechcanada.com.

IS8121 base Do not place

the handset in

the charger.

Add and register a handset

You can add new handsets IS8102

(purchased separately) to your IS8121-2/

IS8121-3/IS8121-4/IS8121-5 telephone

system. Your telephone system supports a

maximum of 5 handsets.

Each handset must be registered with

the telephone base before use. When

first purchased, each expansion handset

displays To register HS... and ... see manual

alternately.

• Charge the new handset without interruption for

at least 30 minutes before registering it to the

telephone base.

• You cannot register a handset if any other system

handset is in use.

To register a handset to IS8121-2 IS8121-3//

IS8121-4/IS8121-5 : telephone base

1. Put the handset you wish to register on the

telephone base cradle.

2. The handset shows Registering.... If the

registration is successful, the handset

screen displays Registered and beeps.

The handset is now registered with the

telephone base.

• If the deregistration process fails, you may

need to reset the system and try again. To reset,

unplug the power from the telephone base and

plug it back in.

• You cannot deregister the handsets if any other

system handset is in use.

• Even if the battery is depleted, you can still

deregister the handsets by following the steps.

After the handset is charged for at least 10

minutes, the screen shows and To register HS...

see manual alternately.

Operating range

This cordless telephone operates with the

maximum power allowed by the Federal

Communications Commission (FCC). Even

so, this handset and telephone base can

communicate over only a certain distance

which can vary with the locations of the

telephone base and handset, the weather,

and the layout of your home or ofﬁce.

When the handset is out of range, the handset

displays Out of range OR no power at base.

If there is a call while the handset is out of

range, it may not ring, or if it does ring, the

call may not connect well when you press .

Move closer to the telephone base, and

then press to answer the call. If the handset

moves out of range during a telephone

conversation, there may be interference. To

improve reception, move closer to the

telephone base.

IS8102

DECT 6.0 accessory handset

for use with VTech models

IS8121-2/IS8121-3/IS8121-4/IS8121-5

The ENERGY STAR® program

(www.energystar.gov) recognizes

and encourages the use of products

that save energy and help protect

our environment. We are proud to

mark this product with the ENERGY

STAR® label indicating it meets the

latest energy efﬁciency guidelines.

Before use

When using your telephone equipment, basic

safety precautions should always be followed to

reduce the risk of ﬁre, electric shock and injury,

including the following:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on

the product.

3. Unplug this product from the wall outlet before

cleaning. Do not use liquid or aerosol cleaners.

Use a damp cloth for cleaning.

4. Do not use this product near water such as near

a bath tub, wash bowl, kitchen sink, laundry tub

or a swimming pool, nor in a wet basement or

shower.

5. Do not place this product on an unstable table,

shelf, stand or other unstable surfaces.

6. Avoid placing the telephone system in places

with extreme temperature, direct sunlight, or

other electrical devices. Protect your phone

from moisture, dust, corrosive liquids and

fumes.

7. Slots and openings in the back or bottom of the

telephone base and handset are provided for

ventilation. To protect them from overheating,

these openings must not be blocked by placing

the product on a soft surface such as a bed, sofa

or rug. This product should never be placed

near or over a radiator or heat register. This

product should not be placed in any area where

proper ventilation is not provided.

8. This product should be operated only from the

type of power source indicated on the marking

label. If you are not sure of the type of power

supply in your home or ofﬁce, consult your

dealer or local power company.

9. Do not allow anything to rest on the power

cord. Do not install this product where the cord

may be walked on.

10. Never push objects of any kind into this product

through the slots in the telephone base or

handset because they may touch dangerous

voltage points or create a short circuit. Never

spill liquid of any kind on the product.

11. To reduce the risk of electric shock, do not

disassemble this product, but take it to an

authorized service facility. Opening or removing

parts of the telephone base or handset other

than speciﬁed access doors may expose you

to dangerous voltages or other risks. Incorrect

reassembling can cause electric shock when the

product is subsequently used.

IMportant safety

instructions

12. Do not overload wall outlets and extension

cords.

13. Unplug this product from the wall outlet and

refer servicing to an authorized service facility

under the following conditions:

• When the power supply cord or plug is

damaged or frayed.

• If liquid has been spilled onto the product.

• If the product has been exposed to rain or

water.

• If the product does not operate normally by

following the operating instructions. Adjust

only those controls that are covered by the

operation instructions. Improper adjustment

of other controls may result in damage

and often requires extensive work by an

authorized technician to restore the product

to normal operation.

• If the product has been dropped and the

telephone base and/or handset has been

damaged.

• If the product exhibits a distinct change in

performance.

14. Avoid using a telephone (other than cordless)

during an electrical storm. There is a remote risk

of electric shock from lightning.

15. Do not use the telephone to report a gas

leak in the vicinity of the leak. Under certain

circumstances, a spark may be created when

the adapter is plugged into the power

outlet, or when the handset is replaced in its

cradle. This is a common event associated

with the closing of any electrical circuit. The

user should not plug the phone into a power

outlet, and should not put a charged handset

into the cradle, if the phone is located in an

environment containing concentrations of

ﬂammable or ﬂame-supporting gases, unless

there is adequate ventilation. A spark in such an

environment could create a ﬁre or explosion.

Such environments might include: medical

use of oxygen without adequate ventilation;

industrial gases (cleaning solvents; gasoline

vapors; etc.); a leak of natural gas; etc.

16. Only put the handset of your telephone next to

your ear when it is in normal talk mode.

17. The power adapter is intended to be correctly

oriented in a vertical or ﬂoor mount position.

The prongs are not designed to hold the plug

in place if it is plugged into a ceiling, under-the-

table or cabinet outlet.

18. For pluggable equipment, the socket-outlet

shall be installed near the equipment and shall

be easily accessible.

19.

CAUTION: Use only the batteries

indicated in this manual. There may

be a risk of explosion if a wrong type of

battery is used for the handset. Use only the

supplied rechargeable batteries or

replacement batteries (BT162342/BT262342)

for the handset. Do not dispose of batteries in

a ﬁre. They may explode.

20. Use only the adapter included with this

product. Incorrect adapter polarity or voltage

can seriously damage the product.

SAVE THESE INSTRUCTIONS

Battery

• CAUTION: Use Only Supplied Battery.

• Do not dispose of the battery in a ﬁre. Check

with local waste management codes for special

disposal instructions.

• Do not open or mutilate the battery. Released

electrolyte is corrosive and may cause burns or

injury to the eyes or skin. The electrolyte may be

toxic if swallowed.

• Exercise care in handling batteries in order

not to create a short circuit with conductive

materials.

• Charge the battery provided with this product

only in accordance with the instructions and

limitations speciﬁed in this manual.

Precautions for users of implanted cardiac

pacemakers

Cardiac pacemakers (applies only to digital

cordless telephones):

Wireless Technology Research, LLC (WTR), an

independent research entity, led a multidisciplinary

evaluation of the interference between portable

wireless telephones and implanted cardiac

pacemakers. Supported by the U.S. Food and

Drug Administration, WTR recommends to

physicians that:

Pacemaker patients

• Should keep wireless telephones at least six

inches from the pacemaker.

• Should NOT place wireless telephones directly

over the pacemaker, such as in a breast pocket,

when it is turned ON.

• Should use the wireless telephone at the ear

opposite the pacemaker.

WTR’s evaluation did not identify any risk to

bystanders with pacemakers from other persons

using wireless telephones.

Connect the charger

Charge the battery

12 hrs

Connect and charge battery

User’s manual

1 – Charging pole

Your telephone package contains the following

items. Save your sales receipt and original

packaging in the event warranty service is

necessary.

What’s in the box

Charger overview

THIS SIDE UP / CE CÔT É VERS LE HAUT

Bat ter y Pac k / Blo c- piles :

BT 162342/BT 262342 (2.4V 300mAh Ni-MH )

WARNING / ERT ISSEMENT :AV

DO NOT BURN O R PUNCT URE BA TT ERIES.

NE S I NCINÉRER O U PERCER LES PI LES.PA

Mad e in C hina / Fabr iqué e n chi ne CR2035

The battery is low and needs charging.

The battery is charging.

The battery is fully charged.

Handset ringer is off.

New voicemail received from your telephone service provider.

NEW

There are new caller ID log entries.

ANS ON Answering system is on.

MSG#

5/10 Number of new/old messages recorded.

ECO The ECO mode activates automatically to reduce power consumption when the

handset is within range of the telephone base.

THIS S IDE UP / CE CÔTÉ VERS LE HAUT

Battery Pack / Bloc-piles :

BT162342/BT262342 (2.4V 300mAh Ni-MH)

WARNING / AVERTISS EMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué e n chine CR2035

THIS SIDE UP

CÔTÉ VERS LE HAUT

mAh Ni-MH)

BATTERIES.

R LES P ILES.

ne CR1535

1 – Visual ringer indicator

2 – CHARGE light

• On when the handset is charging in the

telephone base or charger.

3 – LCD display

4 – /CELL

• Press to make or answer a cell call.

• During a call, press to answer an

incoming cell call when you hear a call

waiting alert.

5 – HOME/FLASH

• Press to make or answer a home call.

• During a call, press to answer an

incoming home call when you receive a

call waiting alert.

6 – 1

• While reviewing a caller ID log entry,

press repeatedly to add or remove 1 in

front of the telephone number before

dialing or saving it in the phonebook.

Battery

indicators

Battery status Action

The screen

is blank, or

shows Put in

charger and

ﬂashes.

The battery

has no charge

or very little

charge. The

handset

cannot be

used.

Charge

without

interruption

(at least 30

minutes).

The screen

shows Low

battery and

ﬂashes.

The battery has

enough charge

to be used for

a short time.

Charge

without

interruption

(at least 30

minutes).

The screen

shows

HANDSET X.

The battery is

charged.

To keep

the battery

charged,

place it in the

charger when

not in use.

Display icons overview

Install the battery

LCD language setting

If you accidentally set the LCD language to Spanish or French, press MENU and then

enter 364# to change the handset LCD language back to English while the handset is

not in use.

The Bluetooth® word mark and logos are owned

by Bluetooth SIG, Inc. and any use of such marks

by VTech Holdings Limited is under license. VTech

Holdings Limited is a member of Bluetooth SIG,

Inc. Other trademarks and trade names are those

of their respective owners.

If registration fails, Registration failed appears on

the handset screen. The handset shows To register

HS... see manual and alternately and the telephone

base returns to idle mode. This may take up to ﬁve

minutes to occur. Please start again from Step 1.

Deregister handsets

If you want to replace a handset or reassign the

designated handset number of a registered

handset, you must deregister all the handsets and

then individually register each handset.

If you want to register a handset to another

telephone base, you must deregister all handsets,

and then register each handset individually to the

desired telephone base.

To deregister all handsets from the telephone base:

1. Press and hold FIND HS on the telephone

base for about 10 seconds until the IN USE

light on the telephone base turns on and

starts ﬂashing.

IS8121 Base

2. Immediately press FIND HS again. You must

press light is still FIND HS while the IN USE

ﬂashing. The IN USE light turns off, and you

hear a conﬁrmation tone.

3. All handsets display To register HS...

and see manual alternately when the

deregistration process completes. The

deregistration process takes about 10

seconds.

For more support information

Handset overview

Produkt Specifikationer

Mærke:	Vtech
Kategori:	Telefon
Model:	IS8102

Har du brug for hjælp?

Hvis du har brug for hjælp til Vtech IS8102 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Telefon Vtech Manualer

Vtech DS6161 Manual

14 December 2024

Vtech DS6621-2 Manual

14 December 2024

Vtech CS6114-21 Manual

14 December 2024

Vtech CS6124-21 Manual

13 December 2024

Vtech CS6929-3 Manual

13 December 2024

Vtech CS6124-11 Manual

13 December 2024

Vtech CS6929-2 Manual

13 December 2024

Vtech IS8101 Manual

13 December 2024

Vtech IS8201 Manual

13 December 2024

Vtech IS8102 Manual

13 December 2024

Telefon Manualer

Nyeste Telefon Manualer

Panasonic KX-TGU410 Manual

14 December 2024

Geemarc CL8510 Manual

11 December 2024

ClearOne Chat 150 Manual

10 December 2024

6 December 2024

6 December 2024

6 December 2024

23 November 2024

Panasonic KX-TGU120AZ Manual

21 November 2024

Panasonic KX-TGU432AZ Manual

21 November 2024

Plantronics Practica T110 Manual

16 November 2024