Vtech VSP500A Manual

Vtech Hovedtelefoner VSP500A

Læs nedenfor 📖 manual på dansk for Vtech VSP500A (4 sider) i kategorien Hovedtelefoner. Denne guide var nyttig for 14 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/4

Parts checklist

Your headset package contains the following

items. Save your sales receipt and original

packaging in the event warranty service is

necessary.

Headset overview

1 – VOL+/VOL-

• Push to right or left to adjust the ringer volume

while in idle mode, or the listening volume while on

a call.

2 – MUTE/FLASH

• Press to mute the ringer in the earpiece when

there is an incoming call.

• Press to mute the microphone during a call.

• Press and hold for two seconds to answer an

incoming call when you receive a call waiting

alert during a call.

3 –

• Press to make, answer or end a call.

4 – Microphone

5 – Battery pack

• Open to replace the battery pack.

6 – Earpiece

Charger overview

1 – Magnetic charging mount

• Place the headset here for charging.

2 – Power cord slot

3 – Power jack

Light and alert tones overview

Light:

light status

Red On when the headset is charging in the •

headset charger.

• Flashes every 10 seconds to indicate

the battery is low when the headset is

not in the headset charger.

• Flashes three times to indicate the

headset is powering off.

Blue On when a fully charged and registered •

headset is in the headset charger.

• Flashes three times to indicate the

headset is powering on.

• Flashes twice every three seconds

when the headset is in use.

• Flashes four times every four seconds

when there is an incoming call.

• Flashes every 10 seconds when a fully

charged and registered headset in idle

mode is out of the headset charger.

Red

and

blue

• Flashes slowly when the headset is not

registered.

• Flashes quickly when the headset is

trying to register to a telephone base.

Off No battery is installed or out of battery.•

• The headset is powered off.

Alert tones:

One short beep Headset key tone.

One short beep

every 30 seconds

Muted headset microphone

alert tone.

Two beeps Error alert tone.•

• The ringer volume is at its

lowest setting.

• The listening volume is at

its highest or lowest setting.

• Any key is pressed while

the headset is out of range

Two low beeps Call waiting alert tone.

Two rapid beeps

every 20 seconds

Low battery warning.

Three rising beeps A conference call starts.

Three rapid beeps

every 20 seconds

• The headset is out of range.

• The headset is not yet

registered.

Ring tone Incoming call alert tone.•

• Ring back tone.

Three rapid beeps The headset is powering on

or off.

Install the battery

NOTE

• The battery is permanently attached to the battery

compartment cover (known as the battery pack). Do

not try to separate them from each other.

Install the battery as shown below.

NOTES

• Use only the supplied battery.

• Remove any headset attachment (earbud excluded)

before battery replacement.

• If the headset will not be used for a long time,

remove the battery to prevent possible leakage.

• To purchase a replacement battery pack (model

BT191665), visit our website at smbphones.vtech.

com or call 1 (888) 370 -2006.

Connect and charge the battery

NOTES

• Use only the supplied adaptor.

• Charge the battery provided with or identiﬁed for

use with this product only in accordance with the

instructions and limitations speciﬁed in this manual.

Connect the charger

Charge the battery

The light turns on when the headset is

charging.

NOTES

• For best performance, keep the headset in the

charger when not in use.

• The battery is fully charged after three hours of

continuous charging.

• When fully charged, the headset battery provides

approximately 12 hours of talk time or 5 days of

standby time.

Before use

Add and register a headset

You can add new

VSP500A

headset (purchased

separately) to your or VSP725A VSP A735

telephone system. Your or VSP725A VSP A735

telephone system supports one headset only.

before use. After charged, the light on headset

ﬂashes in red and blue slowly and alternately.

NOTE

• Charge the new headset without interruption for

at least 30 minutes before registering it to the

telephone base.

To register a headset:

1. Remove the headset from the charger.

2. Press at the telephone base when idle.Menu

3. Press to highlight , and then User Settings

press SELECT.

4. Press to highlight , and DECT headset

then press SELECT.

5. With highlighted, press on Register SELECT

the telephone base.

6. Place the headset back to the charger. The

light ﬂashes quickly in red and blue.

It takes about 60 seconds to complete the

registration process. The light turns red when

the headset is registered but not fully charged,

or turns blue when it is registered and fully

charged.

To verify the registration, press the button on

the headset and check for a dial tone. If the

registration fails, you hear the voice prompt “Not

registered” and the light on the headset ﬂashes

slowly in red and blue.

To reset the headset, remove it from the headset

charger and repeat the registration process

again.

Deregister a headset

To replace a headset or register the headset to

another telephone base, you must deregister

all devices, and then register each device

individually.

To deregister all devices:

1. Press at the telephone base when idle.Menu

2. Press to highlight , and then User Settings

press SELECT.

3. Press to highlight , and DECT headset

then press SELECT.

4. Press to highlight Deregister, and then

press SELECT.

The light ﬂashes slowly in red and blue when

the deregistration process is successful. It takes

about 10 seconds to complete the deregistration

process.

Position the headset

You can choose a suitable size of earbud and an

appropriate way to position your headset.

Earbud

There are three sizes of earbuds provided. The

medium-sized earbud is already attached to the

headset.

To remove the earbud from the headset

earpiece:

• Hold both sides of the earbud. Twist and

pull the earbud until it separates from the

earpiece.

To attach the earbud to the headset

earpiece:

1. Choose an appropriate earbud.

2. Position the earbud on the earpiece.

3. Press the earbud down on the earpiece until

it clicks into place. Move the earbud around

so that the protruding bump on the earbud is

pointing towards your mouth when placed in

your ear.

Over the ear hook

There are two sizes of ear hooks. You can

choose the suitable ear hook to attach to the

headset.

To adjust the headset to wear on the left or

right ear:

To attach the ear hook to the headset:

1. Remove any headset attachment (earbud

excluded) currently connected to the headset.

2. Insert the earpiece into the ear hook ring.

3. Press the edge of the ear hook ring towards

the earpiece until it clicks into place.

4. Hook the headset onto the desired ear.

Adjust the angle of the headset until the

microphone is pointing towards your mouth.

To remove the ear hook from the headset:

• Hold the headset with one hand. Twist and

pull the ear hook with your other hand until it

separates from the earpiece.

Over the head band

To attach the head band to the headset:

1. Remove any headset attachment (earbud

excluded) currently connected to the headset.

2. Insert the earpiece into the loop of the ear pad.

3. Push the earpiece towards the loop of the

ear pad until it clicks into place.

4. Adjust the head band to ﬁt your head. Adjust

and rotate the angle of the headset until the

microphone is pointing towards your mouth.

To remove the head band from the

headset:

• Hold the headset with one hand and the ear

pad with your other hand. Twist and pull the

headset until it separates from the loop of the

ear pad.

Congratulations

on purchasing your new VTech product. Before

using this telephone, please read Important

safety instructions.

This manual has all the feature operations and

frequently asked questions necessary to install

and operate your new VTech product. Please

read this manual thoroughly to ensure proper

installation and operation of this VTech product.

• Cordless headset

with medium-sized

earbud attached

User’s manual

• Headset charger

• Battery pack

(with battery

compartment cover

attached)

• Headset charger

power adapter

• •Earbud x5 Over the ear hook

• •Over the head band Behind the neck

band

• User’s manual

• To wear on the

left ear

• To wear on the

right ear

For customer service or warranty service,

please contact our regional offices / distributors

in the country or region where you purchase

VSP A.735

Quick Start Guide

VSP A500

ErisTerminal™ DECT SIP Cordless H dsetea

for use with VSP725A/VSP73 A 5

Produkt Specifikationer

Mærke:	Vtech
Kategori:	Hovedtelefoner
Model:	VSP500A

Har du brug for hjælp?

Hvis du har brug for hjælp til Vtech VSP500A stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Hovedtelefoner Vtech Manualer

Vtech VSP500A Manual

29 September 2024

Hovedtelefoner Manualer

Nyeste Hovedtelefoner Manualer

Panasonic RP-HC800 Manual

21 December 2024

Panasonic RZ-B310W Manual

21 December 2024

Philips SHE9700BT Manual

21 December 2024

Philips TAA7607 Manual

21 December 2024

Philips TAK4607 Manual

21 December 2024

Philips TAH7508 Manual

21 December 2024

Philips TAGH401 Manual

21 December 2024

Philips TAN7506 Manual

21 December 2024

JBL ROXY Reference 250 Manual

20 December 2024

JBL Reference 250 Manual

20 December 2024