Vulcan 1ER85AF Manual
Vulcan
Frituregryde
1ER85AF
Læs nedenfor 📖 manual på dansk for Vulcan 1ER85AF (64 sider) i kategorien Frituregryde. Denne guide var nyttig for 43 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/64
ERA / EBD ELECTRIC FRYER
See GENERAL section for a complete listing of Models
and ML Numbers.
1ER50-Series
1ER85-Series
2ER50-Series
2ER85-Series
2XER50-Series
2XER85-Series
3ER50-Series
3E85-Series
3ER85-Series
4E50-Series
4ER50-Series
4E85-Series
4ER-Series
- NOTICE -
This Manual is prepared for the use of trained Hobart Service Technicians and should not
be used by those not properly qualified.
This manual is not intended to be all encompassing. If you have not attended a Hobart Service
School for this product, you should read, in its entirety, the repair procedure you wish to
perform to determine if you have the necessary tools, instruments and skills required to
perform the procedure. Procedures for which you do not have the necessary tools,
instruments and skills should be performed by a trained Hobart Service Technician.
The reproduction, transfer, sale or other use of this manual, without the express written
consent of Hobart, is prohibited.
This manual has been provided to you by ITW Food Equipment Group LLC ("ITW FEG")
without charge and remains the property of ITW FEG, and by accepting this manual you agree
that you will return it to ITW FEG promptly upon its request for such return at any time in the
future.
SERVICE MANUAL
A product of Vulcan-Hart 3600 North Point Blvd Baltimore, MD 21222
F25385 (1220)
TABLE OF CONTENTS
Service Updates ............................................................................................ 3
TIS DOCUMENT LIST - ERA/EBD ELECTRIC FRYER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
SERVICE UPDATES ................................................................................... 3
GENERAL .................................................................................................. 4
INTRODUCTION ....................................................................................... 4
SINGLE FLOOR MODEL FRYERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
KLEENSCREEN FILTRATION SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SPECIFICATIONS ...................................................................................... 4
TOOLS ................................................................................................. 5
MODELS AND ML NUMBERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
REMOVAL AND REPLACMENT OF PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
COVERS AND PANELS ................................................................................ 7
COOKING CONTROLS ................................................................................. 8
DISCARD VALVE SWITCH (KLEENSCREEN FRYERS ONLY) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
TEMPERATURE PROBE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
HIGH LIMIT THERMOSTAT ............................................................................ 9
ELECTRICAL COMPONENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
CIRCUIT BREAKER / SUPPLY BOX COMPONENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
FILL SOLENOID VALVE (KLEENSCREEN FRYERS ONLY) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
HEATING ELEMENTS ................................................................................ 11
LIFT ASSIST SPRINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
TILT SWITCH ......................................................................................... 13
PUMP AND MOTOR (KLEENSCREEN FRYERS ONLY) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
SERVICE PROCEDURES AND ADJUSTMENTS ........................................................... 15
TEMPERATURE PROBE TEST ....................................................................... 15
COOKING CONTROL CALIBRATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
LIFT ASSIST SPRING ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
HEATING ELEMENT TEST ............................................................................ 17
ELECTRICAL OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
COMPONENT FUNCTION ............................................................................ 18
COMPONENT LOCATION ............................................................................. 19
SEQUENCE OF OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
SCHEMATIC DIAGRAMS ............................................................................. 23
WIRING DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
ALL MODELS ......................................................................................... 47
FRYMATE (DUMP STATION) WITH OPTIONAL HEATER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
KLEENSCREEN FILTERING SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
ERA / EBD ELECTRIC FRYER
© VULCAN 2020
F25385 (1220) Page 2 of 49
GENERAL
INTRODUCTION
This Service Manual covers specific service
information related to the models listed on the front
cover. ERA and EBD series electric fryers come
equipped with behind-the-door solid state controls.
The features and operation of the cooking controls are
the same for both single floor model fryers and
Kleenscreen battery fryers. All pictures and
illustrations are of a 2ER50AF (17kW, 208V) unless
otherwise noted.
SINGLE FLOOR MODEL FRYERS
Fryers with the Filter-Ready option installed, use the
Mobile Filter. For service information related to the
Mobile filter refer to F24599 MOBILE FILTERS. A
GRO Frymate (dump station) can be configured in a
battery with fryers 15½ inches or 21 inches in width.
Model KILOWATT EACH FRY
TANK
FRYER WIDTH (INCHES)
TOTAL SYSTEM
SHORTENING CAPACITY
(LBS) EACH FRY TANK
1ER50A (1E50BD) 17 15.5 50
1ER50AF (1E50BDF) 17 15.5 50
1ER85A (1E85BD) 24 21.0 85
1ER85AF (1E65BDF) 24 21.0 85
2ER50AF (2E50BDF) 17 31.0 50
2ER85AF (2E85BDF) 24 42.0 85
2XER50AF (2XE50BDF) 17 31.0 50
2XER85AF (2E85BDF) 24 42.0 85
3ER50AF (3E50BDF) 17 46.5 50
3ER85AF (3E85BDF) 24 63.0 85
4ER50AF (4E50BDF) 17 62.0 50
4ER85AF 4E85BDF) 24 84.0 85
KLEENSCREEN FILTRATION
SYSTEM
The Kleenscreen filtration system is integrated into the
ERA & EBD Series fryer battery. The filter is housed
in a pull-out drawer assembly at the base of the fryer.
The filtering components in the drawer include a
stainless steel filter tank, crumb-catch basket and a
dual element mesh filter screen. With the filter drawer
closed, a self-seating oil return line provides the path
to return the filtered shortening to the fry tank.
This system is designed to provide a thorough and
easy method to filter the shortening.
Some of the benefits include:
• Self-contained system eliminating the use of
external filter equipment.
• Paperless filtering system.
• Easy to clean and low maintenance.
Kleenscreen fryer batteries are available in a
minimum of two and a maximum of four fryer sections.
The fryer size of each section is identical.
A GRO Frymate (dump station) can also be included
as one or more of the sections.
SPECIFICATIONS
MODEL
KW PER
FRYER
SECTION
AMPS - EACH FRYER
SECTION
(3 PHASE/ 60HZ)*
PER LINE
208V 240V 480V
ALL 50 LB
CAPACITY
FRYERS
14 39 34 17
17 47 41 20
ERA / EBD ELECTRIC FRYER - GENERAL
F25385 (1220) Page 4 of 49
MODEL
KW PER
FRYER
SECTION
AMPS - EACH FRYER
SECTION
(3 PHASE/ 60HZ)*
PER LINE
208V 240V 480V
ALL 85 LB
CAPACITY
FRYERS
24 67 58 29
NOTES: * Amperage values in the table are
nominal. Tolerance is +5/-10%.
Single Floor Model Fryers
• 208VAC, 240VAC or 480VAC (3 phase, 60HZ) to
power the heating elements.
Drawer Filter System
Separate electrical connections are required for
each section of the battery.
• 208VAC, 240VAC or 480VAC (3 phase, 60HZ) to
power the heating elements.
• On 208VAC and 240VAC models, a transformer
provides power for the fryer controls and drawer
filter system controls.
• On 480VAC models, a 120VAC connection is
required for each fryer section.
TOOLS
Standard
• Standard set of hand tools.
• VOM with minimum of NFPA-70E CATIII 600V,
UL/CSA/TUV listed. Sensitivity of at least 20,000
ohms per volt and the ability to measure DC
micro amps. Meter leads must also be rated at
CAT III 600V.
• Digital temperature tester (thermocouple type).
Special
• Electrostatic Discharge Kit.
• Burndy pin extraction tool RX2025 GE1; Newark
Electronics Catalog Number 16F6666. Used for
removing pin terminals on Burndy connectors.
• Clamp on type amp meter with minimum of
NFPA-70E CAT III 600V,UL/CSA/TUV listed.
MODELS AND ML NUMBERS
The following table contains a complete listing of fryer
models addressed by this Service Manual.
Model ML Number
1ER50A ML-136730
1E50BD
1ER50AF ML-136799
1E50BDF
1ER85A ML-136740
1E85BD
1ER85AF ML-136802
1E85BDF
2ER50AF ML-136741
2E50BDF
2ER85AF ML-136742
2E85BDF
2XER50AF ML-136747
2XE50BDF
3ER50AF ML-136743
3E50BDF
3ER85AF ML-136744
3E85BDF
ERA / EBD ELECTRIC FRYER - GENERAL
Page 5 of 49 F25385 (1220)
Model ML Number
4ER50AF ML-136745
4E50BDF
4ER85AF ML-136746
4E85BDF
ERA / EBD ELECTRIC FRYER - GENERAL
F25385 (1220) Page 6 of 49
REMOVAL AND REPLACMENT OF PARTS
COVERS AND PANELS
Disconnect the electrical power to
the machine and follow lockout /
tagout procedures. There may be
multiple circuits. Be sure all circuits
are disconnected.
Electrical Components Access Panel
1. Remove screws at top of access panel and lower
panel.
2. Lift from hinge then remove panel.
3. Reverse procedure to install.
Element Head Cover
1. Drain shortening from fry tank.
2. Remove screws from rear of element head
assembly.
3. Raise heating elements and place 2x4 lumber
under them for support.
4. Remove screws from the bottom of element head
assembly.
NOTE: Head cover will separate from element head
base. Heating elements remain attached to element
head cover.
5. Grasp heating elements and remove 2x4 lumber.
Lift the elements and pull toward rear of fryer.
6. Lower the heating elements and place them in fry
tank.
7. Reverse procedure to install.
ERA / EBD ELECTRIC FRYER - REMOVAL AND REPLACMENT OF PARTS
Page 7 of 49 F25385 (1220)
COOKING CONTROLS
Disconnect the electrical power to
the machine and follow lockout /
tagout procedures. There may be
multiple circuits. Be sure all circuits
are disconnected.
Certain components in this system are subject to
damage by electrostatic discharge (ESD) during field
repairs. An ESD kit is required to prevent damage. The
ESD kit must be used anytime the circuit board is
handled.
1. Open fryer section door(s).
2. Remove electrical connection to cooking
controls.
3. Remove screws securing controls.
4. Remove cooking control cover.
5. Disconnect lead wires from the component being
replaced then remove from control box.
6. Reverse procedure to install and check for proper
operation.
DISCARD VALVE SWITCH
(KLEENSCREEN FRYERS ONLY)
Disconnect the electrical power to
the machine and follow lockout /
tagout procedures. There may be
multiple circuits. Be sure all circuits
are disconnected.
NOTE: Switches are not adjustable.
1. Open the door to the fryer section being serviced.
2. Disconnect lead wire connector.
3. Remove switch mounting screws.
4. Remove discard valve switch.
ERA / EBD ELECTRIC FRYER - REMOVAL AND REPLACMENT OF PARTS
F25385 (1220) Page 8 of 49
5. Reverse procedure to install and check for proper
operation.
TEMPERATURE PROBE
Disconnect the electrical power to
the machine and follow lockout /
tagout procedures. There may be
multiple circuits. Be sure all circuits
are disconnected.
CAUTION
Do not sharply bend and kink, or clamp down on the
capillary tube or damage may occur.
1. Raise heating elements.
2. Remove clamps from temperature probe.
3. Remove element head cover as outlined under
COVERS AND PANELS.
4. Disconnect temperature probe lead wires.
5. Remove temperature probe from the element
head.
6. Reverse procedure to install.
NOTE: When installing, ensure grommet remains in
place when inserting temperature probe thru the
grommet in the element head.
7. Check cooking control calibration as outlined in
COOKING CONTROL CALIBRATION.
HIGH LIMIT THERMOSTAT
Disconnect the electrical power to
the machine and follow lockout /
tagout procedures. There may be
multiple circuits. Be sure all circuits
are disconnected.
CAUTION
Do not sharply bend and kink, or clamp down on the
capillary tube or damage may occur.
1. Raise heating elements.
2. Loosen clamps securing capillary tube and bulb
to element.
3. Remove element head cover as outlined under
COVERS AND PANELS.
4. Remove high limit from mounting bracket.
ERA / EBD ELECTRIC FRYER - REMOVAL AND REPLACMENT OF PARTS
Page 9 of 49 F25385 (1220)
5. Disconnect high limit lead wires.
6. Remove grommet from the element head
assembly.
7. Remove the bulb, capillary tube and high limit
from the element head assembly.
8. Reverse procedure to install.
A. Slide grommet onto capillary tube then
insert grommet into the capillary tube thru
hole in the element head.
B. Move element lead wires clear of high limit
when installing.
ELECTRICAL COMPONENTS
Disconnect the electrical power to
the machine and follow lockout /
tagout procedures. There may be
multiple circuits. Be sure all circuits
are disconnected.
CAUTION
Components in this system are subject to damage by
electrostatic discharge. A field grounding kit is
available to prevent damage. The field service kit must
be used anytime the control board is handled.
1. Open electrical component access panel.
2. Disconnect lead wires then remove the
component being replaced.
3. Reverse procedure to install the replacement
component and check for proper operation.
CIRCUIT BREAKER / SUPPLY BOX
COMPONENTS
Disconnect the electrical power to
the machine and follow lockout /
tagout procedures. There may be
multiple circuits. Be sure all circuits
are disconnected.
CAUTION
Components in this system are subject to damage by
electrostatic discharge. A field grounding kit is
available to prevent damage. The field service kit must
be used anytime the control board is handled.
NOTE: Supply box will contain a circuit breaker on
24kW 208-240V units.
1. Remove screw and circuit breaker/ supply box
cover.
ERA / EBD ELECTRIC FRYER - REMOVAL AND REPLACMENT OF PARTS
F25385 (1220) Page 10 of 49
2. Disconnect lead wires then remove the
component being replaced.
NOTE: Supply box will contain a circuit breaker on
24kW 208-240V units.
3. Reverse procedure to install the replacement
component and check for proper operation.
FILL SOLENOID VALVE
(KLEENSCREEN FRYERS ONLY)
Disconnect the electrical power to
the machine and follow lockout /
tagout procedures. There may be
multiple circuits. Be sure all circuits
are disconnected.
1. Disconnect swivel pipe fitting at rear of fry tank.
2. Disconnect fill solenoid valve lead wire connector
from below control panel.
3. Remove screws (2) securing the solenoid valve
body flange to pipe tee then remove the
assembly from fryer.
4. Remove pipe fittings from solenoid valve and
install on replacement valve.
5. Reverse procedure to install and check for proper
operation.
HEATING ELEMENTS
Disconnect the electrical power to
the machine and follow lockout /
tagout procedures. There may be
multiple circuits. Be sure all circuits
are disconnected.
CAUTION
Components in this system are subject to damage by
electrostatic discharge. A field grounding kit is
available to prevent damage. The field service kit must
be used anytime the control board is handled.
1. Raise heating elements.
A. If replacing left heating element, loosen high
limit bulb and capillary tube clamps.
Remove high limit bulb and capillary tube
from clamps then position away from
element.
B. If replacing right heating element, remove
temperature probe clamps and position
temperature probe away from element.
ERA / EBD ELECTRIC FRYER - REMOVAL AND REPLACMENT OF PARTS
Page 11 of 49 F25385 (1220)
NOTE: When installing high limit, route the capillary
tube and center the bulb between the clamps before
tightening.
2. Remove element assembly clamps.
3. Remove element head cover as outlined under
COVERS AND PANELS.
4. Disconnect heating element lead wires.
NOTE: Each heating element assembly contains
three individual elements (six lead wire connections
total).
5. Remove screws from heating element mounting
bracket and remove heating element.
6. Reverse procedure to install.
LIFT ASSIST SPRINGS
Disconnect the electrical power to
the machine and follow lockout /
tagout procedures. There may be
multiple circuits. Be sure all circuits
are disconnected.
NOTE: If one spring breaks, replace both springs.
1. Raise heating elements and place 2x4 lumber
under them for support. Heating elements are to
remain upright.
2. Loosen all eye bolt mounting nuts to release
tension on springs.
ERA / EBD ELECTRIC FRYER - REMOVAL AND REPLACMENT OF PARTS
F25385 (1220) Page 12 of 49
3. Remove lift assist springs from the eye bolt
hooks.
4. Remove lift assist springs from the hangers.
5. To install springs:
A. Attach spring hook to hanger thru rear door
opening.
B. Attach spring hook to eye bolt and tighten
eye bolt mounting nut.
C. Remove 2x4 lumber and lower heating
elements.
6. Adjust spring tension as outlined under LIFT
ASSIST SPRING ADJUSTMENT.
TILT SWITCH
Disconnect the electrical power to
the machine and follow lockout /
tagout procedures. There may be
multiple circuits. Be sure all circuits
are disconnected.
1. Remove element head cover as outlined under
COVERS AND PANELS.
2. Lower heating elements.
3. Disconnect lead wires from tilt switch.
4. Remove tilt switch from element head.
REAR VIEW SHOWN, ELEMENTS LOWERED
FRONT VIEW SHOWN, ELEMENTS RAISED
5. Reverse procedure to install and check for proper
operation.
ERA / EBD ELECTRIC FRYER - REMOVAL AND REPLACMENT OF PARTS
Page 13 of 49 F25385 (1220)
PUMP AND MOTOR
(KLEENSCREEN FRYERS ONLY)
Disconnect the electrical power to
the machine and follow lockout /
tagout procedures. There may be
multiple circuits. Be sure all circuits
are disconnected.
1. Drain filter tank of shortening.
2. Open the fryer section doors above the filter tank
drawer.
3. Pull filter drawer out, remove filter tank assembly
and push the tank support arms back into place
under the fryer.
4. Remove splash guard from base frame.
5. Disconnect pump motor lead wire connector.
6. 6. From underneath the fryer: disconnect flexible
line fittings from pump.
7. Remove pump motor assembly from fryer.
8. Remove pipe fittings from the pump and install
on replacement pump.
9. Reverse procedure to install and check for proper
operation.
ERA / EBD ELECTRIC FRYER - REMOVAL AND REPLACMENT OF PARTS
F25385 (1220) Page 14 of 49
SERVICE PROCEDURES AND ADJUSTMENTS
Certain procedures in this section require electrical test or measurements while power is applied to the
machine. Exercise extreme caution at all times. If test points are not easily accessible, disconnect power
and follow lockout / tagout procedures, attach test equipment and reapply power to the test.
TEMPERATURE PROBE TEST
The temperature probe is an RTD (resistance
temperature device) of the thermistor type. As
temperature increases the resistance value
decreases.
Probe Fault
NOTE: A temperature probe fault can be caused by
a lead wire break or a lead short.
If a temperature probe fault occurs:
• The red diagnostic LED on back of control
assembly (inside control box cover) will flash.
• The heat demand outputs are de-activated.
This will continue until the fault clears, power is cycled
or problem resolved.
To Check
1. Turn power switch off.
2. Disconnect cooking control connector.
3. Test the probe using a VOM to measure
resistance. Connect the meter leads to pins 4 &
5 on the male connector.
A. If the measured resistance values are within
the allowable range, the probe is functioning
properly. Reverse procedure to install.
B. If the measured resistance values are
outside the allowable range, install a
replacement probe and check for proper
operation.
Temperature (ºF) Resistance (Ω)
77 90K - 110K
212 5,016 - 6,130
275 1,804 - 2,204
300 1,254 - 1,534
350 646 - 790
392 391 - 478
COOKING CONTROL
CALIBRATION
1. Verify condition of temperature probe as outlined
under TEMPERATURE PROBE TEST.
ERA / EBD ELECTRIC FRYER - SERVICE PROCEDURES AND ADJUSTMENTS
Page 15 of 49 F25385 (1220)
2. Check the level of shortening in fry tank. The level
must be between the MIN & MAX fill lines before
proceeding.
3. Place clamp on type amp meter around any
yellow lead wire of 2CON or 4CON.
4. Allow shortening to cool below 300°F.
5. Place a thermocouple in the geometric center of
the fry tank one inch below the shortening
surface.
6. Set the cooking control to 350°F and turn the fryer
on.
7. Monitor the current as it cycles on and off.
NOTE: Stir shortening to eliminate any cold zones.
A. Allow heat to cycle three times to stabilize
shortening temperature.
B. Record meter reading from thermocouple
when the current cycles off and on for at
least two complete heating cycles.
8. Calculate the average temperature by adding the
temperature reading when the heat goes off to
the temperature reading when the heat comes on
& divide this answer by 2.
[ Temp. (Heat off) + Temp. (Heat on) ] ÷ 2 =
Average Temp.
Example: 360° + 340° ÷ 2 = 350°F. The average
temperature should be 350°F (± 5°F).
A. If the average temperature reading is within
tolerance, cooking control is properly
calibrated.
B. If the average temperature reading is out of
tolerance, loosen set screw to remove
temperature knob and adjust calibration
potentiometer.
NOTE: Ensure that the shaft and knob position does
not change when loosening set screw and removing
temperature knob, as this could affect calibration.
• Adjust calibration potentiometer
clockwise to increase temperature.
• Adjust calibration potentiometer
counterclockwise to decrease
temperature.
C. If over 25° of adjustment is necessary,
replace cooking control.
9. Repeat the average temperature calculation for
up to three attempts. Allow the cooking control to
cycle at least two times between adjustments
before performing the calculation.
10. If calibration is unsuccessful, the cooking control
may be malfunctioning and cannot be adjusted
properly. Install a replacement cooking control
and check calibration.
LIFT ASSIST SPRING
ADJUSTMENT
1. Turn power switch off.
2. Check spring tension:
A. Raise heating elements to the full up
position.
B. Lower heating elements to the full down
position. Elements should remain in place.
C. If the elements remain in place as
described, then no adjustment is necessary.
If the elements do not remain in place,
continue with procedure for adjustment.
ERA / EBD ELECTRIC FRYER - SERVICE PROCEDURES AND ADJUSTMENTS
F25385 (1220) Page 16 of 49
Produkt Specifikationer
| Mærke: | Vulcan |
| Kategori: | Frituregryde |
| Model: | 1ER85AF |
Har du brug for hjælp?
Hvis du har brug for hjælp til Vulcan 1ER85AF stil et spørgsmål nedenfor, og andre brugere vil svare dig
Frituregryde Vulcan Manualer
24 August 2024
24 August 2024
24 August 2024
24 August 2024
24 August 2024
24 August 2024
24 August 2024
24 August 2024
24 August 2024
24 August 2024
Frituregryde Manualer
- Frituregryde DeLonghi
- Frituregryde SilverCrest
- Frituregryde OBH Nordica
- Frituregryde Sencor
- Frituregryde Krups
- Frituregryde Siemens
- Frituregryde Wilfa
- Frituregryde Breville
- Frituregryde Panasonic
- Frituregryde Gorenje
- Frituregryde Miele
- Frituregryde Ninja
- Frituregryde Philips
- Frituregryde Concept
- Frituregryde Gastroback
- Frituregryde Steba
- Frituregryde Vitek
- Frituregryde Rommelsbacher
- Frituregryde AEG
- Frituregryde Electrolux
- Frituregryde Magimix
- Frituregryde Melissa
- Frituregryde Atag
- Frituregryde Presto
- Frituregryde Livoo
- Frituregryde Klarstein
- Frituregryde Tefal
- Frituregryde Trisa
- Frituregryde Princess
- Frituregryde Nedis
- Frituregryde Emerio
- Frituregryde Logik
- Frituregryde Hendi
- Frituregryde Bartscher
- Frituregryde Moulinex
- Frituregryde Sunbeam
- Frituregryde Westinghouse
- Frituregryde Hyundai
- Frituregryde Proctor Silex
- Frituregryde TriStar
- Frituregryde Clas Ohlson
- Frituregryde Black And Decker
- Frituregryde Mestic
- Frituregryde Tomado
- Frituregryde AEG-Electrolux
- Frituregryde Becken
- Frituregryde BEKO
- Frituregryde Küppersbusch
- Frituregryde Privileg
- Frituregryde Clatronic
- Frituregryde Quigg
- Frituregryde SEB
- Frituregryde Buffalo
- Frituregryde Proficook
- Frituregryde Medion
- Frituregryde Fagor
- Frituregryde Haier
- Frituregryde AFK
- Frituregryde Bomann
- Frituregryde Morphy Richards
- Frituregryde Russell Hobbs
- Frituregryde Ariete
- Frituregryde Innoliving
- Frituregryde Zelmer
- Frituregryde Brabantia
- Frituregryde Vivax
- Frituregryde George Foreman
- Frituregryde Kärcher
- Frituregryde Comfee
- Frituregryde Micromaxx
- Frituregryde Cuisinart
- Frituregryde Primo
- Frituregryde Orbegozo
- Frituregryde CaterChef
- Frituregryde Optimum
- Frituregryde Koenig
- Frituregryde Taurus
- Frituregryde Veripart
- Frituregryde Xiaomi
- Frituregryde Elba
- Frituregryde MPM
- Frituregryde Tesla
- Frituregryde G3 Ferrari
- Frituregryde Gourmetmaxx
- Frituregryde Domo
- Frituregryde Saro
- Frituregryde Hamilton Beach
- Frituregryde Ambiano
- Frituregryde Unold
- Frituregryde Bellini
- Frituregryde Nevir
- Frituregryde Imperial
- Frituregryde Eden
- Frituregryde Inventum
- Frituregryde Swan
- Frituregryde Khind
- Frituregryde Midea
- Frituregryde Bimar
- Frituregryde Ardes
- Frituregryde Sogo
- Frituregryde ECG
- Frituregryde Nova
- Frituregryde Saturn
- Frituregryde Eurochef
- Frituregryde Prixton
- Frituregryde Fritel
- Frituregryde Eldom
- Frituregryde H.Koenig
- Frituregryde Proline
- Frituregryde Waves
- Frituregryde Termozeta
- Frituregryde RGV
- Frituregryde Eta
- Frituregryde Bella
- Frituregryde NutriBullet
- Frituregryde Rotel
- Frituregryde Kalorik
- Frituregryde Gemini
- Frituregryde Cecotec
- Frituregryde Cosori
- Frituregryde Solac
- Frituregryde Royal Catering
- Frituregryde Baumatic
- Frituregryde Frifri
- Frituregryde Palson
- Frituregryde Chefman
- Frituregryde Beper
- Frituregryde PowerXL
- Frituregryde Emeril Lagasse
- Frituregryde CRUX
- Frituregryde Tower
- Frituregryde Team
- Frituregryde Brentwood
- Frituregryde Continental Edison
- Frituregryde Arendo
- Frituregryde Lenoxx
- Frituregryde Magic Chef
- Frituregryde Duronic
- Frituregryde Bestron
- Frituregryde Philco
- Frituregryde Waring Commercial
- Frituregryde Novy
- Frituregryde TurboTronic
- Frituregryde Kunft
- Frituregryde Arzum
- Frituregryde Kogan
- Frituregryde Healthy Choice
- Frituregryde DCG
- Frituregryde Oster
- Frituregryde Jocel
- Frituregryde Bourgini
- Frituregryde Ufesa
- Frituregryde Dash
- Frituregryde Comelec
- Frituregryde Lund
- Frituregryde Create
- Frituregryde Mistral
- Frituregryde PRIME3
- Frituregryde Flama
- Frituregryde Kambrook
- Frituregryde Hestan
- Frituregryde American Range
- Frituregryde Aroma
- Frituregryde Salton
- Frituregryde Jata
- Frituregryde Teesa
- Frituregryde JET FRYER
- Frituregryde Heinner
- Frituregryde Guzzanti
- Frituregryde Blokker
- Frituregryde First Austria
- Frituregryde Nordmende
- Frituregryde Limit
- Frituregryde Gallet
- Frituregryde Molino
- Frituregryde Grunkel
- Frituregryde Nesco
- Frituregryde Home Electric
- Frituregryde Elta
- Frituregryde Imarflex
- Frituregryde Livington
- Frituregryde Instant
- Frituregryde Gutfels
- Frituregryde Girmi
- Frituregryde Mia
- Frituregryde Globe
- Frituregryde Herman Den Blijker
- Frituregryde CombiSteel
- Frituregryde Domoclip
- Frituregryde Rival
- Frituregryde Dean
- Frituregryde Magnani
- Frituregryde Avalon Bay
- Frituregryde Wells
- Frituregryde Cecilware
- Frituregryde Carnival King
- Frituregryde BCC
- Frituregryde Petra Electric
- Frituregryde APW Wyott
- Frituregryde Fryclone
- Frituregryde Homie Airfryer S7
- Frituregryde Hatco
- Frituregryde Paragon
- Frituregryde High One
- Frituregryde Perfect Fry
- Frituregryde WestBend
- Frituregryde JAP
- Frituregryde DistinQ
- Frituregryde Just Perfecto
- Frituregryde Bakers Pride
- Frituregryde Monzana
- Frituregryde Casselin
- Frituregryde Kleva
- Frituregryde Swiss Diamond
- Frituregryde AutoFry
- Frituregryde Sierra Range
- Frituregryde Baccarat
- Frituregryde IHarbor
- Frituregryde Anets
- Frituregryde Beautiful
- Frituregryde Roller Grill
- Frituregryde Germanica
- Frituregryde Catler
- Frituregryde Haden
- Frituregryde Stilfer
- Frituregryde Auspure
- Frituregryde Kitchen Couture
- Frituregryde Ultenic
- Frituregryde Electroline
- Frituregryde Masterpro
Nyeste Frituregryde Manualer
12 Marts 2025
5 Marts 2025
19 Februar 2025
19 Februar 2025
12 Februar 2025
7 Februar 2025
7 Februar 2025
2 Februar 2025
15 Januar 2025
15 Januar 2025