Westinghouse 6309135 Manual


Læs nedenfor 📖 manual på dansk for Westinghouse 6309135 (1 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 3 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/1
Installation and Safety Instructions
Warning: Electrical shock can result in serious injury.
Read and follow instructions exactly as shown. If instructions are unclear, do not proceed. Contact a qualified electrician. Read
all instructions before beginning. Proper wiring is essential for safe operation of this fixture. When cutting or drilling into walls
or ceilings, do not damage electrical wiring, gas lines, or water lines. If any of the fixture or wiring components are damaged, do
not install fixture. Return to place of purchase.
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his
service agent or a similar qualified person in order to avoid a hazard.
For indoor use only.
ASSEMBLY INSTRUCTIONS FOR INDOOR LIGHTING FIXTURE
Congratulations on your Westinghouse purchase. This fixture has been designed to give you many years of beauty
and service. For questions and comments, please visit www.westinghouselighting.eu/contact-us and www.
westinghouselighting.de/contact-us
NOTE: Carefully unpack fixture and parts. Make sure all parts are included before discarding any packing materials (see
figure 1).
MOUNTING AND WIRING INSTRUCTIONS
NOTE: Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to this
fixture.
1. Thread mounting screws (A) into the matching holes of mounting bar (B).
2. Place mounting bar (B) flush against ceiling at desired mounting location. Using outside mounting bar holes as a
guide, mark where pilot holes are to be drilled.
3. Inset two plastic anchors (D) into the pilot holes (for drywall ceiling).
4. Align outside mounting bar holes with plastic anchors (D) (If applicable). Secure mounting bar (B) into place using
wood screws (E).
5. If need adjusting length of fixture, loosen set screw (C) at the wire nut (F) and carefully insert/pull the cord (G) into/
from the canopy (H). Then, secure the set screw (C) at the desired wire location.
6. Make an electrical connection by loosening the terminal screws on the terminal block (M) and inserting the live,
neutral and ground terminals.
7. Tighten terminal screws. Make sure there are no stray wires.
8. Raise canopy (H) to ceiling, allowing mounting screw (A) to protrude through openings in canopy (H) and secure into
place with cap nuts (T).
9. Take off the retaining ring (J) from the socket (L). Install the shade (I) and secure with retaining ring (J).
10. Install lamp (K) (not supplied). (Please do not exceed the maximum capacity recommended on the socket).
CLEANING AND CARE
To clean, wipe fixture with soft cloth. Clean glass with mild soap. Spray from chemical cleaners can discolor the finish of
fixture. Do not use scouring pads, powders, steel wool or abrasive paper to clean this fixture.
NOTE FOR FIXTURES THAT ARE SOLID BRASS:
Your hand-crafted, solid brass lighting fixture has been coated with a durable, baked-on acrylic lacquer which gives
maximum protection against the weather. However, in time the brightness of the brass will tarnish, giving way to an
authentic old-world brass finish. To keep your solid brass fixture looking new for years to come, regularly apply a good
quality, non-abrasive car wax to all metal surfaces, giving the fixture an extra protective covering.
Meaning of crossed-out wheeled dustbin:
Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact you local
government for information regarding the collection systems available.
If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get
into the food chain, damaging your health and well-being.
When replacing old appliances with new ones, the retailer is legally obligated to take back your old appliance for disposal
at least free of charge.
Appliance specifications - TECHNICAL CHARACTERISTICS
Rated voltage 220-240V~
Rated frequency 50/60 Hz
Rated wattage E27 Max.40W
Protection class CLASS I
IP number IP20
Ambient temperature 40
o
C
Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A.
www.westinghouselighting.com
, WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF
are trademarks of Westinghouse Electric Corporation.
Used under license by Westinghouse Lighting.
All rights reserved.
Made in China
W-604
052818
*NOT SUPPLIED
FIGURE 1.
D
B
M
A
E
H
F
C
G
T
L
I
*K
J


Produkt Specifikationer

Mærke: Westinghouse
Kategori: Ikke kategoriseret
Model: 6309135

Har du brug for hjælp?

Hvis du har brug for hjælp til Westinghouse 6309135 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Westinghouse Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer