Westinghouse 6324600 Manual
Westinghouse
Lys
6324600
Læs nedenfor 📖 manual på dansk for Westinghouse 6324600 (2 sider) i kategorien Lys. Denne guide var nyttig for 18 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/2
MOUNTING AND WIRING INSTRUCTIONS
NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These fixtures
meet all UL specifications.
1.
Turn off power at circuit box to avoid possible electric shock.
2. Secure mounting bar (A) to outlet box (B) with outlet box screws (C) (
if applicable
) (see fig. 1).
3. Thread hex nut (D) onto mounting nipple (E) approximately 1/4 inch and insert lock washer (F), then
thread mounting nipple (E) into mounting bar (A) and secure hex nut (D). Thread and secure screw
collar (L) onto mounting nipple (E).
4. Thread fixture loop (G) onto center pipe (I). Slide column (I) down over nipple 1 (E1).
NOTE: Do not twist or kink wires when sliding fixture loop (G) downward.
5. Open one link on bottom end of chain (J). Attach to fixture loop (G). Securely close link on chain (J).
6. Insert chain and wires through screw collar ring (K) and canopy (M) and slide screw collar ring (K) and
canopy (M) downward onto the top of the fixture loop (G).
7. Lace wires up through every other link on chain (J).
8. O
pen one link on top end of chain (J). Attach to loop on screw collar (L). Securely close link on chain (J).
Feed wires through screw collar (L) and mounting nipple (E).
9. Identify color coding of fixture wires (see fig. 2).
10. Connect the smooth wire with marking printed or molded from the fixture with the black wire from
outlet box (B)
by wire connector (N), and wrap the wire connector (N) with electrical tape for a
more secure connection.
11. Connect the ribbed wire from the fixture with the white wire from the outlet box (B)
by wire
connector (N), and wrap the wire connector (N) with electrical tape for a more secure connection.
12. Partially thread green grounding screw (O) into side hole (P) on mounting bar (A) (see fig. 1).
13.
Wrap grounding wire from fixture around green grounding screw stem (O) leaving enough excess
wire, then connect the excess grounding wire from the fixture with the grounding wire from outlet
box (B) by wire connector (N) (if applicable), then wrap the wire connector (N) with electrical tape
for a more secure connection.
14. Tighten green grounding screw (O). Do not over tighten.
15. Tuck wires inside outlet box (B).
16. Raise canopy (M) and screw collar ring (K) to ceiling and secure screw collar ring (K) to screw collar (L).
FIXTURE ASSEMBLY INSTRUCTIONS
Warning: This fixture is for indoor use only.
1. Secure threaded end of nipple 2 (E2) into center hole on coupling (W).
2. Slide flat washer 1 (S1) and rubber washer 1 (T1) over nipple 2 (E2). Raise glass (V) up to shade (R),
with nipple 2 (E2) protruding through opening in glass (V),
3. Carefully support glass (V) while securing rubber washer 2 (T2), flat washer 2 (S2), hex nut 2 (K2),
decorative cap (U), and finial (M) to nipple 2 (E2).
4. Install lamp(s). Do not exceed recommended wattage.
5. Turn power back on at circuit box.
Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A. www.westinghouselighting.com
, WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF are trademarks of Westinghouse Electric Corporation.
Used under license by Westinghouse Lighting. All rights reserved. Made in China
WARNING
Turn off electricity to the mounting site before beginning installation.
Mounting instructions must be followed exactly as shown for the fixture to be safely sup-
ported.
CLEANING AND CARE
To clean, wipe fixture with soft cloth. Clean glass with mild soap. Spray from chemical cleaners can
discolor the finish of fixture. Do not use scouring pads, powders, steel wool or abrasive paper to
clean this fixture.
NOTE FOR FIXTURES THAT ARE SOLID BRASS:
Your hand-crafted, solid brass lighting fixture has been coated with a durable, baked-on acrylic lac-
quer which gives maximum protection against the weather. However, in time the brightness of the
brass will tarnish, giving way to an authentic old-world brass finish. To keep your solid brass fixture
looking new for years to come, regularly apply a good quality, non-abrasive car wax to all metal sur-
faces, giving the fixture an extra protective covering.
ORDERING PARTS
Keep this manual for future reference, and in case replacement parts are needed. Available parts can
be ordered from place of purchase. Use exact wording from diagrams when ordering parts.
FIGURE 2.
FIXTURE
WIRES:
Smooth
HOUSE
WIRES:
Black
(Hot)
HOUSE
WIRES:
White
(Neutral)
HOUSE
WIRES:
Bare
Copper
(Ground)
FIXTURE
WIRES:
Bare
Copper
(Ground)
FIXTURE
WIRES:
Ribbed
W-522
042817
WARRANTY INFORMATION
This Westinghouse Lighting Fixture is warranted against defects in material and workmanship for a
period of Five Years from purchase date. This warranty is in lieu of all other warranties expressed or
implied.
This warranty does not cover acts of nature such as lightning damage, or corrosion and discoloration
of components, nor does it cover damages caused through abuse, improper installation, surges in
electric current, or acts of third parties.
This warranty does not cover costs of removing and re-installing the lighting fixture.
If this product fails for any reason covered by this warranty, contact us toll free at 1-888-417-6222.
ASSEMBLY INSTRUCTIONS FOR INDOOR LIGHTING FIXTURE
Congratulations on your Westinghouse purchase. This fixture has been designed to give you many
years of beauty and service. For questions and comments, please visit www.westinghouselighting.
com/contact-us.
NOTE: Carefully unpack fixture and parts. Make sure all parts are included before discarding any
packing materials (see figure 1).
WARNING: ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY.
Read and follow instructions exactly as shown. If instructions are unclear, do not proceed.
Contact a qualified electrician. Read all instructions before beginning. Proper wiring is
essential for safe operation of this fixture. When cutting or drilling into walls or ceilings, do not
damage electrical wiring, gas lines, or water lines. If any of the fixture or wiring components
are damaged, do not install fixture. Return to place of purchase.
For fixtures provided with 75° C or 90° C supply wire warning only. (These warnings are
provided on the U.L. label and on the fixture carton.) Risk of fire. Most dwellings built before
1985 have supply wires rated 60° C. Consult a qualified electrician before installing.
Owner’s Manual
Indoor Lighting Fixture
Installation Instructions
Guide d’utilisation
Instructions d’installation
Appareil d’éclairage pour utilisation intérieure
GARANTIE LIMITÉE DE CINQ ANS
Cet appareil d’éclairage Westinghouse est assorti d’une garantie de 5 ans contre les défauts de
matériaux et de fabrication, qui entre en vigueur à partir de la date d’achat. La présente garantie se
substitue à toute autre garantie expresse ou tacite.
Cette garantie ne porte ni sur les dommages survenant suite à une catastrophe naturelle (telle que la
foudre), ni sur la corrosion ou la décoloration des pièces; la garantie ne porte pas sur les dommages
survenant suite à une utilisation anormale, une installation impropre, une surtension de courant
électrique ou des actes d’un tiers.
Cette garantie ne porte pas sur les frais de démontage et de réinstallation du ventilateur.
Si ce produit ne fonctionne pas, pour une raison quelconque couverte par cette garantie, contactez-
nous gratuitement au numéro suivant : 1-888-417-6222.
MISE EN GARDE: L’ÉLECTROCUTION POURRAIT CAUSER DE GRAVES BLESSURES PERSONNELLES.
Lisez ces instructions et suivez-les exactement comme illustré. En cas de doute, ne commencez
pas l’installation. Consultez un électricien qualifié. Lisez toutes les instructions avant de
commencer l’installation. Un câblage approprié est essentiel au bon fonctionnement de cet
appareil d’éclairage. Lorsque vous faites une entaille ou que vous percez un trou dans un mur
ou un plafond, n’endommagez pas les câbles électriques, les canalisations de gaz ou d’eau. Si
l’un des composants de raccordement ou de l’appareil d’éclairage est endommagé, n’installez
pas cet appareil d’éclairage. Retournez-le à l’endroit où vous l’avez acheté.
Convient uniquement aux appareils comportant un avertissement indiquant que l’appareil
d’éclairage est doté d’un fil supportant une chaleur de 75°C ou 90°C. (Ces avertissements se
trouvent sur l’étiquette U.L. et sur l’emballage de l’appareil d’éclairage.)
LES INSTRUCTIONS D’ASSEMBLAGE DE L’APPAREIL D’ÉCLAIRAGE POUR UTILISATION INTÉRIEURE
Félicitations ! Vous avez acheté un produit de Westinghouse Lighting. Cet appareil d’éclairage a été
conçu pour durer de nombreuses années. Si vous avez des questions ou des commentaires à
nous communiquer, veuillez visiter www.westinghouselighting.com/contact-us.
NOTA : Déballez soigneusement l’appareil d’éclairage et les pièces. Assurez-vous que toutes les pièces
y sont avant de mettre l’emballage au rebut (voir fig. 1).
*NOT SUPPLIED
Line art shown may not exactly match the
fixture enclosed. However, the installation
instructions do apply to this fixture.
FIGURE 1. *GROUND
WIRE
SIDE HOLE (P)
WIRE
CONNECTORS (N)
*OUTLET BOX
SCREWS (C)
LOCK WASHER (F)
HEX NUT (D)
MOUNTING NIPPLE (E)
SCREW COLLAR (L)
CANOPY (M)
CHAIN (J)
SCREW COLLAR
RING (K)
FIXTURE LOOP (G)
CENTER PIPE (I)
NIPPLE 1 (E1)
NIPPLE 2 (E2)
MOUNTING BAR (A)
*OUTLET
BOX (B)
*GREEN GROUNDING
SCREW (O)
DECORATIVE CAP (U)
FINIAL (M)
HEX NUT 2 (K2) FLAT WASHER 2 (S2)
FLAT WASHER 1 (S1)
RUBBER WASHER 2 (T2)
RUBBER WASHER 1 (T1) GLASS (V)
SHADE (R)
COUPLING (W)
*NON FOURNI
Il est possible que le dessin illustré ici ne
soit pas la reproduction exacte de l’appareil
d’éclairage contenu dans la boîte.
Les instructions d’installation demeurent
cependant valables.
FIGURE 1.
TUBE CENTRAL (I)
*FIL DE MISE
A LA TERRE
TROU LATERAL (P)
CONNECTEURS
DE FIL (N)
VIS DE LA BOITE DE
SORTIE DE COURANT (C)
RONDELLE DE
BLOCAGE (F)
L’ECROU HEXAGONAL (D)
MANCHON FILET
DE FIXATION (E)
COLLIER FILETE (L) CHAPEAU (M)
CHAINE (J)
LA BAGUE DU COLLIER
FILETE (K)
LA BOUCLE DE L’APPAREIL
D’ECLAIRAGE (G)
BARRE DE FIXATION (A)
*BOITE DE SORTIE
DE COURANT (B)
*VIS DE MISE A LA
TERRE (O)
RACCORD (W)
MANCHON
FILETE 2 (E2)
MANCHON FILETE 1 (E1)
L’ECROU HEXAGONAL 2 (K2) LA RONDELLE PLATE 1 (S2)
LA RONDELLE PLATE 1 (S1)
RONDELLE EN CAOTCHOUC 2 (T2)
RONDELLE EN
CAOTCHOUC 1 (T1) VERRE 2 (V)
CAPUCHON DECORATIF (U)
ECROU DECORATIF (M)
L’ABAT-JOUR (R)
Produkt Specifikationer
| Mærke: | Westinghouse |
| Kategori: | Lys |
| Model: | 6324600 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Westinghouse 6324600 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Lys Westinghouse Manualer
27 Maj 2024
6 December 2022
23 Oktober 2022
Lys Manualer
- Lys Ikea
- Lys Bosch
- Lys SilverCrest
- Lys Ozito
- Lys Denver
- Lys EasyMaxx
- Lys Siemens
- Lys Beurer
- Lys Metabo
- Lys TP-Link
- Lys RYOBI
- Lys Silverline
- Lys Philips
- Lys Aukey
- Lys Medisana
- Lys IFM
- Lys OK
- Lys LG
- Lys Qtx
- Lys Behringer
- Lys Emos
- Lys Technaxx
- Lys Makita
- Lys Thule
- Lys Livoo
- Lys Toshiba
- Lys Klarstein
- Lys Nikon
- Lys Kodak
- Lys Tracer
- Lys Eheim
- Lys Furrion
- Lys Biltema
- Lys AVM
- Lys Nedis
- Lys American DJ
- Lys Friedland
- Lys Abus
- Lys Adj
- Lys Hama
- Lys Milwaukee
- Lys Dyson
- Lys JBL
- Lys TriStar
- Lys Clas Ohlson
- Lys Sanitas
- Lys Smartwares
- Lys Trust
- Lys Fysic
- Lys Laserliner
- Lys Adler
- Lys Black And Decker
- Lys Crivit
- Lys Livarno
- Lys Mio
- Lys Blaupunkt
- Lys Silva
- Lys Einhell
- Lys Stanley
- Lys Honeywell
- Lys Hikoki
- Lys Hilti
- Lys Festool
- Lys König
- Lys Eglo
- Lys Elro
- Lys Innoliving
- Lys Konstsmide
- Lys Lucide
- Lys Maxim
- Lys Näve
- Lys Nordlux
- Lys Osram
- Lys Sartano
- Lys Steinel
- Lys Gembird
- Lys Deltaco
- Lys Auriol
- Lys Powerfix
- Lys BenQ
- Lys Genie
- Lys Reer
- Lys Craftsman
- Lys Powerplus
- Lys Bresser
- Lys BeamZ
- Lys Goobay
- Lys Digitus
- Lys Sigma
- Lys Alecto
- Lys Cateye
- Lys Astro
- Lys Ansmann
- Lys Xiaomi
- Lys HQ
- Lys AFX
- Lys CAT
- Lys Marmitek
- Lys NGS
- Lys Godox
- Lys Stairville
- Lys Nexxt
- Lys Kathrein
- Lys GoPro
- Lys Fluval
- Lys Ikan
- Lys GlobalTronics
- Lys Reflecta
- Lys Elation
- Lys Omnitronic
- Lys Velleman
- Lys Perel
- Lys Vemer
- Lys GLP
- Lys HQ Power
- Lys Genaray
- Lys Harvia
- Lys Blumfeldt
- Lys Inventum
- Lys Eufy
- Lys Gre
- Lys IDance
- Lys Monacor
- Lys Sun Joe
- Lys Petzl
- Lys Black Diamond
- Lys Brennenstuhl
- Lys DJ Power
- Lys Litecraft
- Lys Cotech
- Lys Chamberlain
- Lys GAO
- Lys Elgato
- Lys Hazet
- Lys GVM
- Lys Steinhauer
- Lys Viessmann
- Lys Trio Lighting
- Lys Brandson
- Lys Martin
- Lys Brilliant
- Lys ARRI
- Lys Hähnel
- Lys Hive
- Lys Anslut
- Lys Runtastic
- Lys Nanlite
- Lys Eurolite
- Lys Vivitar
- Lys Zero 88
- Lys Megaman
- Lys Ledlenser
- Lys Chauvet
- Lys Manfrotto
- Lys Livarno Lux
- Lys Novy
- Lys Nitecore
- Lys Showtec
- Lys GoGen
- Lys Kogan
- Lys Gravity
- Lys Esylux
- Lys NEO Tools
- Lys Smith-Victor
- Lys Olight
- Lys V-TAC
- Lys Schwaiger
- Lys Steren
- Lys Neewer
- Lys Heitronic
- Lys XQ-lite
- Lys Ecolight
- Lys Lupine
- Lys Aqara
- Lys Blackburn
- Lys Media-Tech
- Lys Perfect Christmans
- Lys Digipower
- Lys Lume Cube
- Lys SmallRig
- Lys Rosco
- Lys Light4Me
- Lys Eufab
- Lys Royal Sovereign
- Lys Aputure
- Lys Workzone
- Lys Kichler
- Lys Sygonix
- Lys Yongnuo
- Lys Profoto
- Lys Chrome-Q
- Lys Bazooka
- Lys Infinity
- Lys WiZ
- Lys Rayzr 7
- Lys MTX Audio
- Lys Mission
- Lys SLV
- Lys Integral LED
- Lys DeSisti
- Lys Paulmann
- Lys Fuzzix
- Lys Beghelli
- Lys Berger & Schröter
- Lys Lutec
- Lys Karma
- Lys Wireless Solution
- Lys NUVO
- Lys Neno
- Lys WAC Lighting
- Lys Quoizel
- Lys COLBOR
- Lys Audibax
- Lys Dainolite
- Lys DMT
- Lys Fredrick Ramond
- Lys Magmatic
- Lys Fotodiox
- Lys Crystorama
- Lys ET2
- Lys ProLights
- Lys Golden Lighting
- Lys OttLite
- Lys Sonneman
- Lys Elan
- Lys Kalco
- Lys Livex Lighting
- Lys Hudson Valley
- Lys Hinkley Lighting
- Lys Forte Lighting
- Lys Triton Blue
- Lys Schonbek
- Lys Nicols
Nyeste Lys Manualer
3 December 2024
3 December 2024
2 December 2024
2 December 2024
2 December 2024
2 December 2024
2 December 2024
2 December 2024
2 December 2024
2 December 2024