Yamaha AG06 Manual

Yamaha Stavblender AG06

Læs nedenfor 📖 manual på dansk for Yamaha AG06 (2 sider) i kategorien Stavblender. Denne guide var nyttig for 19 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

9 [GAIN] knobs

Determines the basic volume for each channel, 1 and 2.

Adjust these so that the corresponding [PEAK] LEDs # ﬂash

brieﬂy when singing or playing the loudest.

) [COMP/EQ] button*

This button turns on the compressor and equalizer (yellow

LED lights). The default settings have parameters that are

suitable for webcasting, reducing unwanted low-frequency

noise and variations in input level.

! [AMP SIM] button*

This button turns on the amp simulator (yellow LED lights).

The amp simulator reproduces the sound of using an actual

ampliﬁer. When an electric guitar is directly connected, this

function can reproduce amp "distortion."

@ [EFFECT] buttons*

These buttons turn on the effects on channels 1 and 2 (yellow

LEDs light). The default settings have reverb turned on to add

a natural spaciousness to the sound.

# [PEAK] LED

Lights when the volume of input sound is too high. If it is lit,

turn the [GAIN] knob 9 to the left to lower the volume.

$ Level knobs

Set the volume balance between each channel.

: Adjust the volume of the sound input from the

microphone or other source connected to channel 1.

: Adjust the volume of the sound input from the guitar,

microphone or other source connected to channel 2.

: Adjust the volume of the sound input from the electric

keyboard or other source connected to channels 3/4.

: Adjust the volume of the sound input from the audio

device or other source connected to channels 5/6.

: Adjust the volume of the sound input from the computer

via the [USB 2.0] terminal.

Welcome

Thank you for purchasing the Yamaha AG06 Mixing Console. Please read this manual

thoroughly to get the most out of the product and ensure long-term, trouble-free use. After

reading this manual, keep it readily available for future reference.

For the remainder of this manual, the word "mixer" is used instead of "Mixing Console."

Main Features

Multi-purpose 6-channel mixer with audio interface, ideal for live webcasting

• Audio interface supports up to 24-bit/192 kHz recording.

• An intuitive Loopback function enables fast and easy live webcasting.

• Yamaha's premium “D-PRE” mic preamp provides high resolution sound.

Included Accessories

• USB cable (1.5 m)

• Technical Speciﬁcations (English only): Includes general speciﬁcations, input/output characteristics,

block diagram, dimensions, and jack and plug list.

• CUBASE AI DOWNLOAD INFORMATION: Contains the access code necessary for downloading the

Steinberg DAW software Cubase AI.

• Owner's Manual (this leaﬂet)

Quick Start Guide

Preparation: Download and install drivers.

The "Yamaha Steinberg USB Driver" might be required for computer input/output. Visit the

following Yamaha website for details on downloading and installing the driver, and making

the necessary settings. http://www.yamahaproaudio.com/ag/

STEP 1 Connecting speakers, microphones,

instruments, etc.

1 Turn off the power of all speakers, instruments, and other devices to be

connected to the mixer.

2 Connect speakers, microphones and instruments referring to the connection

example below.

Connection Example

Microphones Electric keyboard

Powered

monitor

speakers Headphones

Portable

audio

player

Headset

Smartphone

Foot switch

(Yamaha FC5)

Computer

Rear panel

Electric guitar

NOTE If you are using condenser microphones, turn on (O) the [+48V] phantom power switch.

STEP 2 Getting sound to the speakers or headphones.

1 Make sure that all switches including the [ ] (Standby/On) switch are not

pressed (N).

2 Use the included USB cable to connect your computer to the mixer.

When using the [USB 2.0] terminal on the mixer's rear panel, refer to the notice

"Precautions when using the [USB 2.0] and [5V DC] terminals."

When connecting a tablet or other device that cannot provide power to the mixer,

connect a commercially available USB power adapter or USB mobile battery to the [5V

DC] terminal (micro B).

3 Turn the [GAIN] knobs, Level knobs, Speakers [ ] knob, and Headphones [ ]

knob fully to the left (minimum).

Level knobs

[GAIN] knobs

Speakers [ ] knob

Headphones [ ]

knob

4 Make sure that the volume of a powered speakers is set to minimum.

5 Turn on the power to connected devices in the following order: Instruments,

audio devices Mixer's [ ] switch Powered monitor speakers.

NOTICE Follow this order to avoid loud, unexpected noise from the speakers. Reverse the order when

turning the power off.

6 For channels to which a microphone or instrument is connected, set the [GAIN]

knob to the 12 o'clock position.

7 Set the Level knobs to the 3 o'clock position.

8 Set the Speakers [ ] knob and the Headphones [ ] knob to the 12 o'clock

position.

9 Speak into your microphone, play your instrument, or play your audio device,

and adjust the volume on the powered monitor speakers.

10 If no sound is heard, or if you want to adjust the volume, follow the instructions

in the boxed section below.

If you still do not hear the sound after doing the following steps, please refer to the

checklist in the "Troubleshooting" section at the back of this booklet.

n There is no sound, or you need to increase the volume

1 Speak into your microphone or play your instrument, turning the [GAIN]

knob to the right so that the corresponding [PEAK] LED flashes briefly.

NOTE • For optimum volume when using a microphone, place the microphone as close to the sound source

as possible.

• If the [PEAK] LED does not light even if the [GAIN] knob has been turned fully to the right, raise the

volume of the sound source (instrument, etc.).

If no sound is heard or the volume does not increase after step 1:

2 If the [PAD] switch or [GAIN] switch is turned on (O), turn the Level knob

fully to the left to "0" (minimum), and then turn off (N) the switches.

3 Slowly turn the Level knob to the right until the desired volume is reached.

n To decrease the volume:

1 Turn the Level knob fully to the left to "0" (minimum), and then turn on (O)

the [PAD] switch or [GAIN] switch on the channel for which you want to

decrease the volume.

2 Slowly turn the Level knob to the right until the desired volume is reached.

If the volume does not decrease after the above steps:

3 Lower the volume of the instrument or audio device.

ZN24020

MIXING CONSOLE

Owner’s Manual

Controls and Functions 1 [USB 2.0] terminal

For connecting to a computer using the included USB 2.0

cable. When connected to a computer, the computer supplies

power to the mixer and audio data can be sent between

the mixer and computer. A USB driver might be required for

computer input/output. You can download the driver from the

following Yamaha website, and install it on your computer.

http://www.yamahaproaudio.com/ag/

NOTICE

Please do not connect any device to [USB 2.0] terminal other than

personal computers or tablet devices.

[5V DC] terminal

For connecting to a commercially available USB power

adapter or USB mobile battery. Use this terminal when

connecting the mixer to a tablet or other device that cannot

supply power to the mixer. A USB power adapter or USB

mobile battery is not included with the mixer.

NOTICE

• Please read the safety precautions for the USB power adapter or

USB mobile battery you are using.

• Use a USB power adapter or USB mobile battery that can supply

power via a USB micro B plug based on the following USB standards:

Output voltage: 4.8 V to 5.2 V

Output current: 0.5 A or greater

% [STEREO OUT] jacks

Outputs the mixed signal in stereo. These jacks are used to

connect to another mixer or recorder. They support phone

plugs. The signal output from these jacks is not affected by the

[TO PC] slide switch D or the Speakers [ ] knob F.

^ [MONITOR OUT] jacks

For connecting to powered monitor speakers. These jacks

support phone plugs (balanced/unbalanced).

& [FOOT SW] jack

For connecting to a separately-sold foot switch (Yamaha FC5,

etc.).

When the [EFFECT] button @ is turned on, the effected sound

can be muted with a foot switch. The [EFFECT] button LED

ﬂashes while the effected sound is muted.

* Headphones [ ] output jack

For connecting to a set of headphones. This jack supports a

stereo phone plug. To connect headphones or earphones with

stereo mini plugs, you can use the [HEADSET] headphones

output jack (.

MIC/LINE input jacks

For connecting to a microphone, an instrument, or an audio

device. These jacks support both XLR and phone plugs.

XLR Phone

4 LINE input jacks

For connecting to line-level devices such as an electric

keyboard or an audio device. Channels 3/4 support

phone plugs, and channels 5/6 support RCA plugs. Use

the [L/MONO] jack on channels 3/4 for instruments, etc.

with mono output. In this case, the sound input to the

[L/MONO] jack is output from both the L channel and R

channel on the mixer.

5

[+48V] phantom switch / [+48V] LED

When this switch is turned on ( O), the [+48V] LED lights

and DC +48 V phantom power is supplied to the XLR plug

connected to the MIC/LINE input jack 3 on channel 1. Turn

this switch on when using a phantom-powered condenser

microphone.

NOTICE

Be sure to leave this switch off (N) if you do not need phantom power.

Follow the important precautions below, in order to prevent noise and

possible damage to external devices as well as the mixer if you turn this

switch on (O).

• Be sure to leave this switch off (

N) when you connect a device that

does not support phantom power to channel 1.

• Make sure to turn this switch off (

N) when connecting/disconnecting a

cable to/from channel 1.

• Turn the Level knob of the channel 1 to "0" (minimum) before turning

this switch on (O)/off (N).

6 [PAD] switches

Turning the switch on (O) will attenuate the sound input to

the unit. If you hear distortion or the [PEAK] LED # lights

frequently even if the [GAIN] knob 9 is turned fully to the left,

turn this switch on.

NOTE Turn the Level knob to minimum before toggling the [PAD]

switch on ( O) and off (N). Otherwise, noise may be

produced.

7 [GUITAR] switch

For switching (on/off) the input impedance on channel 2. Turn

this switch on when directly connecting an instrument with

high output impedance, such as an electric guitar or electric

bass, to channel 2. When this switch is turned on, use an

unbalanced cable with phone plugs to connect the instrument

to the mixer. The mixer will not operate correctly if a balanced

cable is used.

CAUTION

When operating this switch, turn all output controls (such as the

Speakers [ ] knob F and Headphones [ ] knob G) fully to

minimum. Sudden high level peaks caused by the switching operation

can damage external equipment as well as the hearing of those

present.

8 [GAIN] switches

Determines the basic volume for each channel, 3/4 and 5/6.

Turn this switch on (O) if you hear distortion.

NOTE Turn the Level knob to minimum before toggling the [PAD]

switch on ( O) and off (N). Otherwise, noise may be

produced.

( [HEADSET] microphone [ ] input jack

For connecting to the microphone for your headset. Normally

this plug is color-coded in pink. The audio input here is sent to

channel 1.

NOTE If a microphone is connected to the [HEADSET] microphone

input jack, the sound from the microphone or instrument

connected to the MIC/LINE input jack

3 on channel 1 is cut

off.

[HEADSET] headphones [ ] output jack

For connecting to the headphone for your headset. Normally

this plug is color-coded in light green. The same sound as for

the headphones [ ] output jack * is output.

NOTE If a headphone plug is connected to the [HEADSET]

headphones [ ] output jack, the sound output from the

headphones [ ] output jack * is cut off.

A [ ] (Standby/On) switch

For turning the power of the unit to standby ( N) and on (O).

NOTICE

Rapidly switching the [ ] switch between on and standby in succession

can cause the mixer to malfunction. After switching the [ ] switch to

standby, wait for at least six seconds before turning it on again.

B [AUX] input jack

This is an auxiliary input jack. It supports a stereo mini plug.

You can connect a smartphone or other device and use

applications to trigger sound effects or background music.

Use the controls on the connected device to adjust volume.

C Level meter

If the level of the sound sent to the computer exceeds -10

dBu, [SIG] (green) turns on; if the level reaches 3 dB before

clip level (+7 dBu), [PEAK] (red) turns on. To send an

appropriate volume to the computer, adjust the volume of

each channel until [SIG] remains lit and [PEAK] ﬂashes only

momentarily when there is a loud sound.

D [TO PC] slide switch

Select the sound to send to the computer.

[DRY CH 1-2]:

Sends the sound after [GAIN] knob adjustments (dry signal)

from channels 1 and 2 directly to the computer. The sound

that is sent is not affected by Level knob adjustments. The

sounds input to channels 1 and 2 (guitar and vocal, etc.) can

be recorded separately, as with an audio interface.

[INPUT MIX]:

The sound input into the mixer and mixed in stereo is sent to

the computer. Sound input from the computer is not sent back

to the computer.

[LOOPBACK]:

The sound input into the mixer and the sound played on the

computer are mixed in stereo and sent to the computer. This

setting is used primarily for webcasting.

NOTE To prevent feedback when using DAW software, use either

[DRY CH1-2] or [INPUT MIX].

E [MONITOR MUTE] switch

When this switch is on ( O), sound input to channels 1 and 2

is not output from the [MONITOR OUT] jacks ^, headphones

[ ] output jack *, and [HEADSET] headphones [ ] output

jack (

(direct monitoring is OFF).

F Speakers [ ] knob**

Adjust the volume sent to the device connected to the [MONITOR

OUT] jacks.

G Headphones [ ] knob**

Adjust the volume to headphones connected to the

Headphones [ ] output jack * and [HEADSET] headphones

[ ] output jack (.

** The Speakers [ ] knob and Headphones [ ] knob can be

adjusted separately.

*You can use a dedicated application to set the detailed

settings for [COMP/EQ] ), [AMP SIM] !, and [EFFECT] @.

Visit the following Yamaha website for details.

http://www.yamahaproaudio.com/ag/

n Resetting )/!/@ to factory default settings

Turn the [ ] switch A on while pressing and holding down

the [COMP/EQ] button ).

)

% ^

(

Front panel

Rear panel

n Tips on volume adjustment

Use the [PAD] switches, [GAIN] knobs/ [GAIN] switches, and Level knobs to adjust volume. However, the [PAD] switches and [GAIN] knobs/

[GAIN] switches should not be adjusted again once they have been set optimally. Normally, the Level knobs are used to adjust volume. For

details about each function, see "Controls and Functions".

Mixer Basics: Where Your Sound Goes

Input the sound from a

microphone or instrument

Adjust the volume, tone,

and effects of each channel

The sound from all

channels ows rightward

5 Output the sound

from speakers or

headphones

4 Final adjustment of

the volume of the

mixed sound

Channel number

Produkt Specifikationer

Mærke:	Yamaha
Kategori:	Stavblender
Model:	AG06
Bredde:	155 mm
Dybde:	202 mm
Højde:	63 mm
Vægt:	1000 g
Produktfarve:	Hvid
USB-port:	Ja
Antal USB 2.0-porte:	1
Strømforbrug (typisk):	2.5 W
Mac kompabilitet:	Ja
AUX-indgang:	Ja
Mikrofonindgang:	Ja
Videofunktion:	Ingen
Understøttede Windows-operativsystemer:	Ja
Understøttede Mac-operativsystemer:	Ja
Tilslutning af hovedtelefoner:	3,5 mm
Udgang til hovedtelefoner:	Ja
Antal kanaler:	6 kanaler
Prøvetagningshastighed:	192 kHz
Digital lydbehandling:	24 Bit
DJ mixer:	Ingen
Monitor udgang:	1