Yuneec Typhoon G Manual

Yuneec Legetøj Typhoon G

Læs nedenfor 📖 manual på dansk for Yuneec Typhoon G (1 sider) i kategorien Legetøj. Denne guide var nyttig for 7 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/1

The SteadyGrip™ is a ground handle designed to extend the GoPro® camera from

the sky to the ground, allowing you to capture amazing acon shots easier than

ever before. The camera pitch controller allows precise camera angle control on the

go using your mobile device as a display. The SteadyGrip's ergonomic design is

capable of holding up to a 6.4 inch mobile device.

The GB203 is a 3-Axis brushless self-stabilizing gimbal, compable with GoPro®

Hero 3, Hero 3+, Hero 4 Black and Hero 4 Silver, extending the use of the GoPro®

Camera to capture smooth and ﬂuid photographs and video footage on the ground,

and amazing video footage in the sky as well.

Please take the me to read through this enre instrucon manual for more

informaon on safety, baery charging, camera controls and more before ﬁlming

your ﬁrst hit video. Please also visit www.Yuneec.com for addional informaon

including product updates, bullens, videos and more.

GENERAL SAFETY PRECAUTIONS AND WARNINGS

WARNING: Failure to use this product in the intended manner as described in

instrucon manual can result in damage to the product, property and/or cause

serious injury. This product is not a toy! If misused it can cause serious bodily harm

and damage to property.

WARNING: As the user of this product you are solely and wholly responsible for

operang it in a manner that does not endanger yourself and others or result in

damage to the product or the property of others.

Always allow GB203 and SteadyGrip™ to inialize properly by seng the Steady-

Grip™ on a ﬂat and stable surface prior to switching it on and allowing the Steady-

Grip™ and GB203 to inialize properly which somemes takes about 12 seconds.

Always operate your SteadyGrip™ in a respecul and safe manner.

FCC STATEMENT:

This equipment has been tested and found to comply with the limits for Part 15

of the FCC rules. These limits are designed to provide reasonable protecon

against harmful interference in a residenal installaon. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instrucons, may cause harmful interference to radio

communicaons.

However, there is no guarantee that interference will not occur in a parcular

installaon. If this equipment does cause harmful interference to radio or

television recepon, which can be determined by turning the equipment oﬀ and

on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separaon between the equipment and receiver.

BATTERY WARNINGS AND USAGE GUIDELINES

WARNING: Alkaline Baeries May explode or leak, and cause burn injury if

recharged, disposed of in ﬁre, mixed with a diﬀerent baery type, inserted

backwards or disassembled. Replace all baeries at the same me. Do not carry

baeries loose in your pocket or purse. Do not remove the baery label.

WARNING: All instrucons and precauons must be read and followed exactly

and you must follow instrucons of the baery manufacturer.

INSTALLING THE AA BATTERIES

WARNING: Alkaline Baeries May explode or leak, and cause burn injury if

recharged, disposed of in ﬁre, mixed with a diﬀerent baery type, inserted

backwards or disassembled. Replace all baeries at the same me. Do not carry

baeries loose in your pocket or purse. Do not remove the baery label.

NOTICE: The use of rechargeable baeries is only recommended.

ATTACHING THE GB203 TO THE STEADYGRIP™

WARNING: Before switching on the SteadyGrip™ it is highly recommended to ﬁrst

securely aach the GB203 to your SteadyGrip™.

QUICK TIP: Make sure that you have your microSD card with lots of space for

photos and videos handy.

STEP 1) Remove the protecve cover for the contactor as illustrated.

STEP 2) Carefully slide the top part of the GB203 (that also aaches below the

nose of the TYPHOON) onto the mount below the front part of the SteadyGrip™. A

corresponding ‘click’ will be noced once the GB203 has securely been installed

into the slide-in mount on the SteadyGrip™.

GoPro® COMPATIBLE DEVICES

Android:

Depending on devices

Windows Phone (8 & 8.1)²

NOTICE: Please refer to the oﬃcial website of GoPro® for the latest

informaon.

WINDOWS SYSTEM

REQUIREMENTS

Windows XP (Service Pack 2 or later)

or Vista

3.2GHz Penum 4 or faster

Minimum 4GB of system RAM

MAC SYSTEM

REQUIREMENTS

Mac OS® X 10.4.11 or later

2.0GHz Intel Core Duo or faster

Minimum 4GB of system RAM

NOTICES AND WARNINGS

IMPORTANT NOTE: All safety precauons and warnings, instrucons, warranes

and other collateral informaon is subject to change at the sole discreon of

Yuneec. For the most up-to-date informaon please visit the corresponding

product page at www.Yuneec.com or contact the nearest Yuneec oﬃce or

authorized distributor.

The following special language terms are used throughout the product literature to

indicate various levels of potenal harm when operang this product:

NOTICE: Procedures, which if not properly followed, create a possibility of property

damage and/or lile to no possibility of injury.

CAUTION: Procedures, which if not properly followed, create the probability of

property damage and/or a possibility of serious injury.

WARNING: Procedures, which if not properly followed, create the probability of

property damage, collateral damage and/or serious injury or create a high probability

of superﬁcial injury.

WARNING: Read the ENTIRE instrucon manual to become familiar with the

features of the product before operang. Failure to operate the product correctly

can result in damage to the product, property and/or cause serious injury.

WARNING: This is a sophiscated consumer product. It must be operated with

cauon and common sense, and requires some basic mechanical ability. Failure to

operate this product in a safe and responsible manner could result in damage to the

product, property and/or cause serious injury. This product is not intended for use

by children without direct adult supervision. Do not use with incompable

components or alter this product in any way outside of the instrucons provided by

Yuneec. The instrucon manual contain instrucons for safety, operaon and

maintenance. It is essenal to read and follow all the instrucons and warnings

prior to assembly, setup and/or use in order to operate the product correctly and

avoid damage or serious injury.

AGE RECOMMENDATION: NOT FOR CHILDREN UNDER 14 YEARS. THIS IS NOT

A TOY.

Apple iOS:

iphone/ipad/ipod touch

OVERVIEW

SteadyGrip™ and GB203

for GoPro® Cameras

1. GB203

2. Main Status LED

3. Pitch Control Roller Wheel

4. Mode Switch Buon

5. Rubberized Ergonomic Grip

6. On/Oﬀ Switch

7. 8x AA Baery Compartment

STEP 1) Remove the Baery Cover / Door from the boom of the SteadyGrip™

Hold the boom of the SteadyGrip™ toward yourself with the front part facing

downward. Slide the baery cover / door upward with slight force and inspect the

AA baery compartment.

STEP 2) Install 8x AA Baeries

Install 8x AA Baeries as illustrated.

STEP 3) Re-installing the Baery Cover / Door on the boom of the SteadyGrip™

Once you’ve installed 8 fresh AA baeries, Hold the boom of the SteadyGrip™

toward yourself with the front part facing downward. Slide the baery cover / door

downward with slight force and ensure you hear and feel a noceable ‘click’

indicang the baery cover / door has been closed securely.

STEP 3) Powering on and inializaon. Place your

SteadyGrip™ on a ﬂat and stable surface, then switch

on the SteadyGrip™ and it will inialize aer 12

seconds of no movement or vibraon. The LED Status

indicator on the GB203 will blink green slowly when

inializaon is completed.

GB203 LED Status:

GB203 Connecng with the SteadyGrip: LED blinking green slowly

GB203 Failing to Connect with the SteadyGrip: LED oﬀ

GB203 Connecng with the Remote Controller: LED blinking green slowly

GB203 Error: LED blinking red

CUSTOMER SERVICE

YUNEEC EU

24568 Kaltenkirchen, Germany

+49 4191 932620

eusales@yuneec.com

YUNE EC AU

53 Ellemsea Circuit, Lonsdale

South Australia 5160

+61 (0) 8 8186 3301

aussales@yuneec.com

YUNEEC USA

5555 Ontario Mills Parkway,

Ontario, CA91764, USA

1 855 2848888

sales@yuneec.com

YUNEEC HK

2/F, Man Shung Industrial Building,

7 Lai Yip Street, Kwun Tong,

Kowloon, Hong Kong

852 3616 6071

asiasales@yuneec.com

hp://yuneec.com/support

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Any informaon above might be changed due to the soware update.

For the latest documents, please check the oﬃcial website.

CAMERA CONTROL

Please be sure to set photo or video mode for GoPro® Camera BEFORE installing

it into the GB203. Any operaon related to camera controls should be referred to

and downloaded according to the oﬃcial website of GoPro®. GoPro® requires

APP to take photos and record videos.

NOTICE: MK58 is for long-distance real-me image transmission when installing

it on the aircra.

SWITCHING THE MODE

There are two modes of Pitch Follow Mode and Angle Mode.

Pitch Follow Mode allows the gimbal camera to track SteadyGrip in pitch

direcon. The Main Status LED indicator will be solid green.

In Angle Mode, the camera lens scks to a ﬁxed direcon instead of following the

movement of the SteadyGrip. The user can control the Pitch Direcon through

pitch control roller wheel.

NOTICE: The default mode of SteadyGrip is Pitch Follow Mode.

To Enter Angle Mode:

Press the Mode Switch Buon on the top of the SteadyGrip to exit the Pitch

Follow mode. The Main Status LED indicator will blink GREEN. The SteadyGrip

will enter Angle Mode.

To Enter Pitch Follow Mode:

Press Mode Switch Buon again to enter Pitch Follow Mode. The Main Status

LED indicator will be solid green.

NOTE: When SteadyGrip™ is in Pitch Follow status, the gimbal camera tracks

SteadyGrip™ in pitch direcon, and the gimbal pitch control roller wheel on

SteadyGrip™ is disabled.

WARNING: procedures, which if not properly followed, create the probability of

property damage, collateral damage and serious injury or create a high probability

of superﬁcial injury.

Failure to exercise care while using this product and comply with the following

condions and guidance could result in product malfuncon, excessive heat, ﬁre,

property damage, and ulmately injury.

Lithium lon baeries are not toys. For the purpose of the document Li-lon, Li-Po,

Li-Fe, NiCd or NiMH baeries will be described as "Baeries".

Handling and Storage:

● Never alter, puncture or impact Baeries or related components.

● Do not directly connect the terminals with metal objects. This will short-circuit

Baeries, resulng in heat and electrical discharge.

● Never store loose Baeries together, the Baeries' terminals may contact one

another causing a short circuit.

● Never expose Baeries to extreme temperatures or direct sunlight.

● Always disconnect Baeries when not in use.

Before the First Charge:

● Ensure baeries are not damaged, as this may cause a short circuit of ﬁre. Charging

● Always refer to your charger's manual to ensure safe operaon.

● Always charge Baeries in an open area away from ﬂammable materials, liquids and surfaces.

● Never charge Baeries that are hot to the touch (above 120°F)

If at any me Baeries become damaged, hot, or begin to balloon or swell,

disconnue charging (or discharging) immediately. Quickly and safely disconnect

the charger. Then place the Baeries and/or charger in a safe, open area away from

ﬂammable materials in an approved Li-Po bag to observe. Aer one hour, remove

the Baeries from service. DO NOT connue to handle, aempt to use, or ship the

Baeries. Failure to follow these procedures can cause damage to Baeries,

personal property or cause serious injury.

Damaged or swollen Baeries can be unstable and very hot. DO NOT touch

baeries unl they have cooled. Dispose of baeries in the manner required by

your city, county, state or country. Contact the appropriate Yuneec Product

Support Oﬃce to speak to a service technician for more informaon.

In the event of ﬁre, a Class D, dry chemical ﬁre exnguisher must be used then

baeries must be placed inside of an approved Li-Po bag.

Addional Guidelines and Warnings:

● In the event of a crash, always quickly and safely disconnect and remove Baeries

from the model. Then follow the previously listed safety procedures.

● If the internal contents of Baeries come into contact with your skin, wash the

aﬀected area(s) with soap and water immediately. If it comes into contact with your

eye(s), ﬂush them with generous amounts of water for 15 minutes and seek

immediately medical aenon.

• Connect the equipment to an outlet on a circuit diﬀerent from that to which the

receiver is connected.

This device complies with part 15 of the FCC rules. Operaon is subject to the

following two condions:

(1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired

operaon.

NOTE: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protecon against harmful interference in a

residenal installaon. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instruc-

ons, may cause harmful interference to radio communicaons. However, there is

no guarantee that interference will not occur in a parcular installaon. If this

equipment does cause harmful interference to radio or television recepon, which

can be determined by turning the equipment oﬀ and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separaon between the equipment and receiver.

—Connect the equipment into an outlet on a circuit diﬀerent from that to which

the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

RF EXPOSURE WARNING

• This equipment must be installed and operated in accordance with provided

instrucons and the antenna(s) used for this transmier must be installed to

provide a separaon distance of at least 20 cm from all persons and must not be

co-located or operang in conjuncon with any other antenna or transmier.

End-users and installers must be provide with antenna installaon instrucons and

transmier operang condions for sasfying RF exposure compliance.

IC RADIATION EXPOSURE STATEMENT FOR CANADA

This device complies with Industry Canada licence-exempt RSS standard(s).

Operaon is subject to the following two condions: (1) this device may not cause

interference, and (2) this device must accept any interference, including interfer-

ence that may cause undesired operaon of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux

appareils radio exempts de licence. L'exploitaon est autorisée aux deux

condions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)

l'ulisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si

le brouillage est suscepble d'en compromere le fonconnement.

This equipment complies with IC RSS-102 radiaon exposure limit set forth for an

uncontrolled environment.

Cet équipement respecte les limites d'exposion aux rayonnements IC déﬁnies

pour un environnement non contrôlé

ATTACHING A MOBILE DEVICE TO THE STEADYGRIP™

Step 1) Press the Curved Lip at the top

front of the SteadyGrip™ as illustrated

and ﬁt your Mobile Device with the

screen facing toward the Main LED and

Pitch Control Wheel.

Step 2) Bind your Mobile Device to the

GoPro® camera.

The SteadyGrip™ features a camera pitch controller that allows precise camera

angle control on the go. Simply roll the pitch control wheel forward to move the

camera pitch/angle downward and roll the pitch control wheel backward to move

the camera pitch/angle upward. Please review these instrucons along with the

illustraons to familiarize yourself on how to control the GB203 and GoPro®

camera with your SteadyGrip™.

USING THE CAMERA PITCH CONTROL WHEEL

GROUND IMAGING SYSTEM

INTRODUCTION

GROUND IMAGING SYSTEM

NOTICE: The GB203 can be supplied with power through SteadyGrip™ by the Lipo

Balance Connetor Charge Lead (sold seperately) when the contact is damaged.

SteadyGrip™ LED STATUS:

Main Status LED:

Upon Powering on: Green LED blinking for twice and

then solid GREEN

Low Voltage Warning: RED LED blinking slowly

Power Cut-oﬀ: RED LED blinking quickly

Pitch Follow Funcon on: GREEN LED solid

Pitch Follow Funcon oﬀ: GREEN LED blinking

SPECIFICATIONS

STEADYGRIP™

Height: 223mm (8.78 in)

Depth (front to back): 182mm (7.17 in)

Width: 70mm (2.76 in)

Weight (without gimbal/baeries): 254g (8.96 oz)

Angle Control Range (Pitch): 30° to -90°

Runme: 240 min (depending on usage)

GB203

Dimensions: 110*80*115mm(4.33*3.15*4.53in)

Weight(without camera): 145g(5.11oz)

Pitch Control Range: 30°~-90°

Pitch Mechanical Range: 75°~-120°

Roll Mechanical Range: -45°~+45°

Yaw Mechanical Range: -45°~+45°

Compable Device: GoPro®Hero 3, Hero 3+, Hero 4 Black, Hero 4

Silver

NOTICE: If use MK58, GoPro®Hero4 Black is suggested to achieve

Produkt Specifikationer

Mærke:	Yuneec
Kategori:	Legetøj
Model:	Typhoon G

Har du brug for hjælp?

Hvis du har brug for hjælp til Yuneec Typhoon G stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Legetøj Yuneec Manualer

Yuneec Typhoon G Manual

14 August 2024

Yuneec Typhoon H Manual

11 August 2024

Yuneec E-Go 2 Manual

23 Juli 2024

Yuneec Typhoon Wizard Manual

18 Juli 2024

Yuneec Typhoon Q500 plus Manual

18 Juli 2024

Yuneec Tornado H920 Manual

17 Juli 2024

Legetøj Manualer

Nyeste Legetøj Manualer

Lego Bakery 40696 Manual

20 December 2024

Lego 40701 Manual

20 December 2024

Lego 40611 Manual

20 December 2024

Lego Friends 42637 Manual

20 December 2024

Lego 40692 Manual

19 December 2024

Lego Icons 10391 Manual

19 December 2024

Lego Creator 66791 Manual

19 December 2024

Lego Wednesday 40750 Manual

19 December 2024

Lego City 60436 Manual

19 December 2024

Lego Brickheadz 40552 Manual

19 December 2024