Audio-Technica AT4022 Manual


Læs nedenfor 📖 manual på dansk for Audio-Technica AT4022 (2 sider) i kategorien Mikrofon. Denne guide var nyttig for 17 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
OMNIDIRECTIONAL CONDENSER MICROPHONE
- Outstanding performance and rugged construction, ideal for critical
studio & live applications
- High SPL handling and wide dynamic range
- Flat, extended frequency response
- Switchable 80 Hz hi-pass lter and 10 dB pad
- Omnidirectional polar pattern provides maximum ambient pickup
- Low self-noise perfectly suited for digital recording equipment
- Exceptional reproduction of low-frequency sounds
- Low-mass element for superb transient response
The AT4022 is intended for use in professional applications where
remote power is available. It requires 48V DC phantom power, which
may be provided by a mixer or console, or by a separate, in-line
source such as the Audio-Technica AT8801 single-channel or AT8506
four-channel phantom power supplies.
Output from the microphones XLRM-type connector is low
impedance (Lo-Z) balanced. The signal appears across Pins 2 and
3; Pin 1 is ground (shield). Output phase is “Pin 2 hot” positive
acoustic pressure produces positive voltage at Pin 2.
To avoid phase cancellation and poor sound, all mic cables must be
wired consistently: Pin 1-to-Pin 1, etc.
An integral 80 Hz hi-pass filter provides easy switching from a flat
frequency response to a low-end roll-off. The roll-off position reduces
the microphone's sensitivity to popping in close vocal use. It also
reduces the pickup of low-frequency ambient noise (such as trafc,
air-handling systems, etc.), room reverberation and mechanically-
coupled vibrations.
Avoid leaving the microphone in the open sun or in areas where
temperatures exceed 43°C for extended periods. Extremely high
humidity should also be avoided.
FORM No. ATGC-L0146-08-E
Machida Tokyo Japan
SPECIFICATIONS
ELEMENT Fixed-charge back plate
permanently polarized condenser
POLAR PATTERN Omnidirectional
FREQUENCY RESPONSE 20-20,000 Hz
OPEN CIRCUIT SENSITIVITY -34 dB (19.9 mV) re 1V at 1 Pa
IMPEDANCE 250 ohms
MAXIMUM INPUT SOUND LEVEL 146 dB SPL, 1 kHz at 1% T.H.D.
156 dB SPL, with 10 dB pad (normal)
NOISE 13 dB SPL
DYNAMIC RANGE (typical) 133 dB, 1 kHz at Max SPL
SIGNAL-TO-NOISE RATIO 81 dB, 1 kHz at 1Pa
LOW FREQUENCY ROLL-OFF 80 Hz, 12 dB/octave
PHANTOM POWER REQUIREMENTS 48V DC, 3.0 mA typical
WEIGHT (less accessories) 124 g
DIMENSIONS 144.0 mm - long,
21.0 mm - body diameter
OUTPUT CONNECTOR Integral 3-pin XLRM-type
ACCESSORIES FURNISHED AT8405a snap-in clamp for ⅝”-27
threaded stand; windscreen;
protective carrying case
10 dB
20k10k5k2k1k50020010050
8 kHz
200 Hz
1 kHz
5 kHz
330°
300°
270°
240°
210°
180°
150°
120°
90°
60°
30°
Polar Pattern
Frequency Response
SCALE IS 5 DECIBELS PER DIVISION
LEGEND
Frequency in Hertz
LEGEND 12” or more on axis
Response in dB
Optional Accessories:
AT8506 four-channel 48V phantom power
supply (AC powered).
AT8801/EU single-channel 48V phantom
power supply (AC powered).
Roll-off
Same as 1 kHz


Produkt Specifikationer

Mærke: Audio-Technica
Kategori: Mikrofon
Model: AT4022

Har du brug for hjælp?

Hvis du har brug for hjælp til Audio-Technica AT4022 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Mikrofon Audio-Technica Manualer

Mikrofon Manualer

Nyeste Mikrofon Manualer

PSC

PSC RF Multi SMA Manual

17 December 2024
PSC

PSC PowerStar RF Manual

17 December 2024
Hollyland

Hollyland LARK M1 Manual

16 December 2024
Power Dynamics

Power Dynamics PD210 Manual

16 December 2024
Vimar

Vimar 20586 Manual

15 December 2024
Vimar

Vimar 19586.M Manual

15 December 2024
Vimar

Vimar 20586.B Manual

15 December 2024
Vimar

Vimar 20586.N Manual

15 December 2024
Vimar

Vimar 19586 Manual

15 December 2024
Vimar

Vimar 19586.B Manual

15 December 2024