Audio-Technica AT846/O Manual


Læs nedenfor 📖 manual på dansk for Audio-Technica AT846/O (2 sider) i kategorien Mikrofon. Denne guide var nyttig for 23 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
OMNIDIRECTIONAL CONDENSER BOUNDARY MICROPHONE
10 dB
20k10k5k2k1k50020010050
8 kHz
200 Hz
1 kHz
5 kHz
330°
300°
270°
240°
210°
180°
150°
120°
90°
60°
30°
Optional Accessories:
AT8506 four-channel 48V phantom
power supply (AC powered).
AT8801/EU single-channel 48V
phantom power supply (AC pow-
ered).
Polar Pattern
Frequency Response
SCALE IS 5 DECIBELS PER DIVISION
LEGEND
Frequency in Hertz
LEGEND 12” or more on axis
Response in dB
FORM No. ATGC-L0183-11-E
Machida Tokyo Japan
SPECIFICATIONS
ELEMENT Fixed-charge back plate
permanently polarized condenser
POLAR PATTERN Omnidirectional
FREQUENCY RESPONSE 54-20,000 Hz
OPEN CIRCUIT SENSITIVITY -33 dB (22.4 mV) re 1V at 1 Pa
IMPEDANCE 100 ohms
MAXIMUM INPUT SOUND LEVEL 131 dB SPL, 1 kHz at 1% T.H.D.
SIGNAL-TO-NOISE RATIO >69 dB, 1 kHz at 1Pa
PHANTOM POWER REQUIREMENTS 11-52V DC, 2 mA typical
WEIGHT 48 g
DIMENSIONS 30.0 mm - diameter,
64.6 mm - length
OUTPUT CONNECTOR Integral 3-pin XLRM-type
ACCESSORIES FURNISHED One pair isolators
The AT 8 4 6 /O is a wide- r a n ge
condenser microphone with an
omn i d irec tio n a l po lar p a tte r n .
It is de s i g ned fo r u n o b tr u s i v e
table, ceiling or panel-mounted
applications for high-quality sound
reinforcement, teleconferencing,
professional recording, television
a n d o t h e r d e m a n d i n g s o u n d
pickup applications.
T h e AT 8 4 6 / O i s e q u i p p e d
w i t h U n iG ua r d ® R F I - sh i e l d in g
t e c h n o l o g y , w h i c h o f f e r s
out s tand i n g r e jecti o n o f r adio
frequency interference (RFI). The
microphone is RoHS compliant
free from all substances specified
in the EU directive on hazardous
substances.
The microphone should be placed on a at, unobstructed mounting
surface. The small diameter capsule near the boundary eliminates
phase distortion and delivers clear, high-output performance.
The microphone requires 11V to 52V phantom power for operation.
The microphone is enclosed in a heavy-duty die-cast case and
protected by a two-layer steel mesh grille. The low-profile housing
has a low-reflectance black finish. Isolators are included with the
microphone for optional mechanical isolation from the mounting
surface.
Output is low impedance balanced. The balanced signal appears
across Pins 2 and 3, while the ground (shield) connection is Pin 1.
Output is phased so that positive acoustic pressure produces positive
voltage at Pin 2 in accordance with industry convention.
To mount the AT846/O in a ceiling or table top without the isolators,
a 20.5 mm diameter hole is required. To mount the AT846/O with the
isolators, a 23.5 mm hole is required. Place the isolators on either
side of the hole to achieve mechanical isolation from the mounting
surface.
The microphone shall be a xed-charge condenser designed for use
in table, ceiling or panel-mount boundary applications. It shall have
a frequency response of 54 Hz to 20,000 Hz and an omnidirectional
polar pattern. It shall have a self-contained power module and shall
operate from an external 11V to 52V DC phantom power source.
It shall offer outstanding rejection of radio frequency interference
(RFI). It shall be capable of handling sound input levels up to 131
dB. Nominal open circuit output voltage shall be 22.4 mV at 1 kHz, 1
Pascal. Output shall be low impedance balanced (100 ohms) from an
integral 3-pin XLRM-type connector.
The microphone shall have a maximum diameter of 30.0 mm and an
overall length of 64.6 mm. Weight shall be 48 grams. The microphone
shall be housed in an all-metal case with a two-layer steel mesh
grille. Finish shall be low reectance black. Resilient isolators shall be
provided for reduction of mechanical noise transfer from the mounting
panel.
Avoid leaving the microphone in the open sun or in areas where
temperatures exceed 43 C for extended periods. Extremely high °
humidity should also be avoided.


Produkt Specifikationer

Mærke: Audio-Technica
Kategori: Mikrofon
Model: AT846/O

Har du brug for hjælp?

Hvis du har brug for hjælp til Audio-Technica AT846/O stil et spørgsmål nedenfor, og andre brugere vil svare dig




Mikrofon Audio-Technica Manualer

Mikrofon Manualer

Nyeste Mikrofon Manualer

PSC

PSC RF Multi SMA Manual

17 December 2024
PSC

PSC PowerStar RF Manual

17 December 2024
Hollyland

Hollyland LARK M1 Manual

16 December 2024
Power Dynamics

Power Dynamics PD210 Manual

16 December 2024
Vimar

Vimar 20586 Manual

15 December 2024
Vimar

Vimar 19586.M Manual

15 December 2024
Vimar

Vimar 20586.B Manual

15 December 2024
Vimar

Vimar 20586.N Manual

15 December 2024
Vimar

Vimar 19586 Manual

15 December 2024
Vimar

Vimar 19586.B Manual

15 December 2024