Audio-Technica AT8539 Manual


Læs nedenfor 📖 manual på dansk for Audio-Technica AT8539 (1 sider) i kategorien Mikrofon. Denne guide var nyttig for 3 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/1
Features
HRS-type input connector allows any A-T Wireless Essentials®
microphone to function as a wired model
Switchable low-cut lter minimizes pickup of unwanted low
frequencies
XLRM-type output connector
Designed to plug directly into an XLR-type chassis connector
Rugged steel case construction
Description
The AT8539 power module allows any Audio-Technica Wireless
Essentials® microphone to operate as a wired microphone. The power
module’s HRS-type 4-pin input connector mates with any Audio-Technica
Wireless Essentials® (wireless microphone with model number ending in
a cW); its output is a standard 3-pin XLRM-type connector.
It offers a low-cut lter to help minimize the pickup of unwanted low
frequencies. To engage the low-cut lter, use the end tip of a paperclip or
other small pointed instrument to slide the switch toward the “bent” line.
The power module is constructed of rugged steel for maximum durability
and optimum shielding from hum. A snap-on belt clip is included.
Architect’s and Engineers Specications
The in-line power module shall allow any Audio-Technica wireless
microphone terminated with a 4-pin HRS-type connectors to connect
to a wired microphone circuit. The input connection shall be through an
HRS-type 4-pin connector. Output shall be a standard 3-pin XLRM-type
connector. The power module shall convert the audio signal to a standard
balanced line microphone level output as well as provide operating DC
bias voltage for the attached microphone. An integral low-cut lter shall,
when engaged, roll off the low-end audio at 80 Hz with a slope of 18 dB
per octave. The lter shall be engaged via a recessed switch. The power
module shall be constructed of metal for optimum shielding from hum.
Output impedance shall be 250 ohms.
The Audio-Technica AT8539 is specied.
Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224
Audio-Technica Limited, Old Lane, Leeds LS11 8AG England
©2010 Audio-Technica U.S., Inc. audio-technica.com 0001-0239-00
Specications
HRS-type 4-pin / XLRM-type
Microphone dependent
250 ohms
80 Hz, 18 dB/octave
11-52V DC, 2 mA typical
Flat / Roll-off
97.6 mm (3.84") long ,
18.9 mm (0.74") diameter
Belt clip
Input/Output connectors
Frequency response
Impedance
Low-cut lter
Phantom power
Switch
Dimensions
Accessory included
In the interest of standards development, A.T.U.S. offers
full details on its test methods to other industry profes-
sionals on request.
Specications are subject to change without notice.
AT8539
Power Microphones
electronics


Produkt Specifikationer

Mærke: Audio-Technica
Kategori: Mikrofon
Model: AT8539

Har du brug for hjælp?

Hvis du har brug for hjælp til Audio-Technica AT8539 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Mikrofon Audio-Technica Manualer

Mikrofon Manualer

Nyeste Mikrofon Manualer

PSC

PSC RF Multi SMA Manual

17 December 2024
PSC

PSC PowerStar RF Manual

17 December 2024
Hollyland

Hollyland LARK M1 Manual

16 December 2024
Power Dynamics

Power Dynamics PD210 Manual

16 December 2024
Vimar

Vimar 20586 Manual

15 December 2024
Vimar

Vimar 19586.M Manual

15 December 2024
Vimar

Vimar 20586.B Manual

15 December 2024
Vimar

Vimar 20586.N Manual

15 December 2024
Vimar

Vimar 19586 Manual

15 December 2024
Vimar

Vimar 19586.B Manual

15 December 2024