Audio-Technica ES925ML/DS5 Manual

Audio-Technica Mikrofon ES925ML/DS5

Læs nedenfor 📖 manual på dansk for Audio-Technica ES925ML/DS5 (4 sider) i kategorien Mikrofon. Denne guide var nyttig for 21 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/4
1
Introduction
Thank you for purchasing this product. Before using the product, read through
the user manual to ensure that you will use the product correctly. Please keep
this manual for future reference.
Features
• Modular microphone system comprised of an ES Series capsule, gooseneck
assembly, and power module.
• RGB LEDs built into both the desk stand power module and gooseneck
assembly indicate the on/off status of the microphone.
• Includes external control function for device control from the capacitive touch
switch.
• The capacitive touch switch can be set to any of three operating modes:
“touch-on/touch-off”, “touch-to-talk” and “touch-to-mute”.
Safety precautions
Although this product was designed to be used safely, failing to use it correctly
may result in an accident. To ensure safety, observe all warnings and cautions
while using the product.
Cautions for the product
• Do not subject the product to strong impact to avoid malfunction.
• Do not disassemble, modify or attempt to repair the product.
• Do not handle the product with wet hands to avoid electric shock or injury.
• Do not store the product under direct sunlight, near heating devices or in a
hot, humid or dusty place.
Notes on use
• Do not swing or pull the product. Doing so may cause disconnection or
damage.
• The circuitry in the microphone takes about 30 seconds to stabilize after power
is supplied. You may hear some audio disturbance during startup.
The connectors are equipped with a special RFI-shielding mechanism. If you
remove or replace the connector, you may adversely affect the microphone’s RFI
immunity. The Audio-Technica Crimp Tool (ATCT) and shield parts are required to
shorten the cable and reinstall the connector while maintaining the RFI immunity.
• Install the microphone on a flat, unobstructed mounting surface. Make sure
that the sound source is not below the mounting surface.
• Depending on the surface finish of a table, the desk stand power module may
leave marks on the table.
• Do not excessively bend the gooseneck assembly, rotate the ends of the
capsule, or pull on them. Doing so may cause disconnection or malfunction.
• The product is a modular system comprised of a microphone element,
gooseneck assembly and power module. Make sure the parts are firmly
attached before use.
• Do not remove the rubber O-ring on the power module connecting part at the
lower section of the gooseneck assembly.
• When attaching parts, remove the black cap on the capsule connecting part
of the gooseneck assembly. Do not remove the silicone part at the end of
the capsule connecting part.
Silicone part
Do not remove
Switch settings
To reduce low-frequency ambient noise (such as footsteps or air conditioning
noise), room reverberation, and mechanically coupled vibrations as much as
possible, turn on the low-cut filter switch ( ) on the bottom of the power
module.
ES925ML6/DS5
ES925ML12/DS5
ES925ML15/DS5
ES925ML18/DS5
ES925ML21/DS5
ES925ML24/DS5
User Manual
MICROLINE CONDENSER
MODULAR GOOSENECK MICROPHONE
WITH 5-PIN DESK STAND POWER MODULE


Produkt Specifikationer

Mærke: Audio-Technica
Kategori: Mikrofon
Model: ES925ML/DS5

Har du brug for hjælp?

Hvis du har brug for hjælp til Audio-Technica ES925ML/DS5 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Mikrofon Audio-Technica Manualer

Mikrofon Manualer

Nyeste Mikrofon Manualer

Shure

Shure MoveMic Manual

17 November 2024
Comica

Comica DUAL.LAV D03 Manual

17 November 2024
BOYA

BOYA BY-PM500W Manual

17 November 2024
Elgato

Elgato Wave Panels Manual

16 November 2024
Warm Audio

Warm Audio WA-8000 Manual

15 November 2024
Pyle

Pyle PDWM3100 Manual

15 November 2024
Behringer

Behringer TM1 Manual

15 November 2024
Yamaha

Yamaha RM-WCH-8 Manual

14 November 2024
Yamaha

Yamaha RM-WOH Manual

14 November 2024