Bintec-elmeg CS410-U Manual

Bintec-elmeg Telefon CS410-U

Læs nedenfor 📖 manual på dansk for Bintec-elmeg CS410-U (76 sider) i kategorien Telefon. Denne guide var nyttig for 23 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/76
Ope ra ting in struc tions
En glish
el meg CS290
el meg CS290-U
el meg IP-S290plus
Ope ra ting in struc tions
En glish
el meg CS290
el meg CS290-U
el meg IP-S290plus
Plea se no te!
The sys tem te le pho nes and cor re spon ding sys tems in this user gui de use the fol lo wing ab bre via tions:
Sys tem / PABX: Ab bre via ti on:
el meg PABX el meg PABX
el meg Hy bird 300
el meg Hy bird 600
elmeg hybird. Al ter na ti ve con fi gu ra ti on of the sys tem te le pho nes (see also page 67)
Bin tec TR200aw as PABX
Bin tec TR200bw as PABX
Declaration of Conformity and CE Mark
This de vi ce meets the re qui re ments of R&TTE Di rec ti ve 1999/5/EC:
»Di rec ti ve 1999/5/EC of the Eu ro pe an Par lia ment and of the Coun cil of 9 March 1999 on ra dio equip -
ment and te le com mu ni ca tions ter mi nal equip ment and the mu tu al re co gni ti on of their con for mi ty«.
The De cla ra ti on of Con for mi ty can be vie wed at the fol lo wing web ad dress: http://www.bin tec-el -
meg.com.
The cros sed-out was te bin icon on the de vi ce in di ca tes that the de vi ce must be dis po sed of se pa ra te ly from nor mal
hou se hold was te at the dis po sal si tes pro vi ded at the end of its ser vi ce li fe. You can find ad di tio nal in -
for ma ti on on the in di vi du al re turn of used de vi ces at www.bin tec-el meg.com.
© bin tec el meg GmbH - All rights re ser ved.
This do cu ment may not be re pro du ced, in full or in part, ex cept with the ap pro val of the pub lis her and with a de tai led
re fer en ce to the sour ce pub li ca ti on, ir re spec ti ve of the na tu re and me thod or me dia (me cha ni cal or elec tro nic) by
which this is pro du ced.
Functio nal des crip tions of this do cu men ta ti on that re la te to soft wa re pro ducts of ot her ma nu fac tu rers are ba sed on
the soft wa re used at the time of crea ti on or prin ting. The pro duct or com pa ny na mes used in this do cu men ta ti on may
in so me ca ses be re gis te red tra de marks.
Tab le of con tents
Te le pho ne user in ter fa ce. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Des crip ti on and in stal la ti on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
elmeg CS410 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
elmeg CS410-U. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
elmeg IP-S400 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Sa fe ty no ti ces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Un pa cking and po si tio ning the sys tem te le pho ne . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Connecting the system telephone (connector and receiver cord) . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Changing the label field . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Pictograms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Sys tem te le pho ne set tings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Setting the display language. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Te le pho ning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Initiate a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Accepting/rejecting a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Forwarding a call (Call Deflection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Suppressing the call number (anonymous call) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Initiating a call with a fixed call number (MSN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Redialling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Switching the microphone on/off, loudspeaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Using the headset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Announcement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Automatic callback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Intercept (MCID). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Keypad and tone dialling (MFC dialling) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Te le pho ning with se ve ral peo ple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Call Waiting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Hold for enquiry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Call forwarding (call transfer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Brokering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Conference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Ope ra te sys tem te le pho ne . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
VIP memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Caller history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
SMS and UUS1 text messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Che cking costs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Tab le of con tents
I
Viewing and deleting costs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Set up tariff factor and denomination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Sys tem te le pho ny . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Function keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Function keys when connecting to a elmeg hybird or PABX . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Sys tem menu on elmeg PABX with sys tem te le pho ny . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Con fi gu ring and set ting the sys tem te le pho ne . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Advanced configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Acoustic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Display contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Con fi gu ra ti on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
elmeg IP-S400 configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Ser vi ce..........................................................57
In dex. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Op tions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Quick In stall Gui de . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Tab le of con tents
II
Te le pho ne user in ter fa ce
1Functi on key: Open the pro gram ming menu by pres sing this key. If you are al rea dy in a menu and press this
key, the functions avai la ble in this menu will be dis play ed or you will be ta ken back one pro gram ming step.
2Es ca pe key: By pres sing the es ca pe key, the te le pho ne is once again at rest du ring pro gram ming.
33 soft keys
In the PC con fi gu ra ti on of the te le pho ne you can spe ci fy whet her the functions of soft keys are dis play ed
only with up per ca se or lo wer ca se letters.
4Dis play: Af ter con nec ting to the po wer supp ly ( ) or to the in ter nal ISDN or flush-moun -elmeg IP-S400
ted(elmeg CS410 ,elmeg CS410-U ) con nec ti on of the elmeg PABK, the date and time shall be dis play ed to
you on the top line. Both the date and time are au to ma ti cal ly co pied from the elmeg PABK. The text dis play -
ed for a functi on in line 2 can al ways be found abo ve the cor re spon ding soft key. If you press the soft key, the
next le vel is then dis play ed.
If not all of the cha rac ters can be shown in the dis play, this is in di ca ted by »»« or »»«.
5OK key: Af ter pres sing this but ton the set ting is then sto red in the te le pho ne. You will then hear an ac -
knowled ge tone.
6C-key: You can go back one menu step by pres sing this key in any menu. If you are in in put mode, you can
de le te in di vi du al cha rac ters using this key.
7Call re min der LED: An in co ming call is in di ca ted by ra pid flas hing.
8Loud spea ker
9Loud spea ker key (hands free key elmeg IP-S400)
0Di vert key
ßHold key
°Re di al key
§Ar row key: The ar rows »{« and »}« in the right-hand cor ner of the top line of the dis play show you that you
can ac cess ot her functions in the se cond line by using the ar row key.
Te le pho ne user in ter fa ce
1
1 2 3
4 5 6
789
0
W
T
L
R
F E O
< > C
* #
z
z
z
z
z
90ß$%& /
°§
$
21 3 6 78 54
Fig: 1
$Star key / hash key
%Op ti on keys / VIP keys
&elmeg CS410-U: 5 pro gram ma ble functi on keys with LEDs: Each key has a two-co lour LED (Le vel 1 - Red /
Le vel 2 - Yel low). The se LEDs can be used to in di ca te spe ci fic functions.
elmeg CS410: Each key has a (red) LED avai la ble. The LEDs for both of the lo wer functi on keys have two co -
lours (Le vel 1 - Red / Le vel 2 - Yel low). The se LEDs can be used to in di ca te spe ci fic functions.
/La bels for pro gram ma ble functi on keys
Te le pho ne user in ter fa ce
2
Des crip ti on and in stal la ti on
The sys tem te le pho ne can be ope ra ted by an in ter nal con nec tor of a elmeg PABX that supp orts sys tem functions.
To get her with the elmeg PABX, the sys tem te le pho ne pro vi des va ri ous per for man ce fea tu res that are typical of this
system.
The in ter nal con nec tor on the elmeg PABX is si mul ta ne ous and au to ma ti cal ly the sys tem in ter fa ce for the sys tem te -
le pho ne. Plea se con sult the user’s gui de for your elmeg PABX to see whet her or not this of fers the ty pi cal sys tem per -
for man ce fea tu res com bi ned with various system telephones.
UA com ple te con fi gu ra ti on of the elmeg PABX and di rect ly via the sys tem te le pho ne is pos si ble on
all elmeg PABX (ex clu ding elmeg hybird) using the Pro fes sio nal Con fi gu ra tor.
UA com ple te con fi gu ra ti on of the te le pho ne using the elmeg hybird is not pos si ble. So me of the
per for man ce fea tu res can on ly be set up using the telephone’s own in ter fa ces. Ho we ver, this is
on ly pos si ble if the sys tem te le pho ne has a USB or Ether net in ter fa ce.
Functions that can not be ful ly con fi gu red via the elmeg hybird are mar ked at ap pro pria te points
in the text.
Differences in configuration between the elmeg PABX and the elmeg hybird
b
c
Press a soft key or an ar row key. On the elmeg hybird this key does not have to be pres sed again if the dis play
is dif fe rent, as the functi on is al rea dy dis play ed or is not avai la ble.
The fol lo wing mes sa ge in di ca tes if dif fer en ces exist.
Cannot be configured using the system telephone on the elmeg hybird!
A sum ma ry of the se functions can be found on pa ge 67un der »Re stric ted sys tem te le pho ne con fi gu ra ti on«.
elmeg CS410
This sys tem te le pho ne is de sig ned for con nec ti on to an in ter nal S-con nec tor (4-wi re ca ble) on a elmeg PABX.
elmeg CS410-U
This sys tem te le pho ne is de sig ned for con nec ti on to an in ter nal Up0-con nec tor (2-wi re ca ble) on a elmeg PABX. The
sys tem te le pho ne has an ISDN con nec ti on to which furt her ISDN ter mi nals can be connected.
elmeg IP-S400
This sys tem te le pho ne is con nec ted to the cor re spon ding LAN con nec ti on (or net work) of the elmeg PABX by a Cat. 5
ca ble.The sys tem te le pho ne has an PC con nec ti on to which furt her IP ter mi nals can be connected.
Setting / configuring the system telephone
On the sys tem te le pho ne it self, you can on ly per form a re stric ted con fi gu ra ti on of the sup por ted per for man ce fea tu -
res. A com ple te con fi gu ra ti on of the sys tem is on ly pos si ble via the cor re spon ding con nec tors of theelmeg PABX.
elmeg CS410 Des crip ti on and in stal la ti on
3
Sa fe ty no ti ces
·Note the am bient tem pe ra tu re for the sto ra ge and ope ra ti on of the de vi ce in the spe ci fi ca tions.
The de vi ce must only be con nec ted once the per mis si ble am bient ope ra ting temperature is
reached.
·Plea se note that when swit ching from cold to warm tem pe ra tu res, con den sa ti on may form on or
in the de vi ce. Only re mo ve the de vi ce from the pa cka ging when the per mis si ble am bient ope ra -
ting tem pe ra tu re has been reached.
·Du ring a storm, you should not con nect or dis con nect any ca bles and do not make any calls.
·Only con nect the cords to the con nec tors pro vi ded.
·Lay the cords so that they are pro tec ted in the event of an ac ci dent.
·Avoid the fol lo wing in flu en cing fac tors:
Di rect sun light
Sour ce of heat (e.g. ra di ator)
Elec tro nic de vi ces (e.g. sound sys tems, office equip ment or mi cro wa ve de vi ces)
Pe ne tra ting moi stu re or li quids
Ag gres si ve li quids or vapours
High levels of dust
·Do not use the de vi ce in hu mid rooms or in ex plo si ve at mo sphe res.
·Only open the are as of the de vi ce in di ca ted in the as sem bly/ope ra ting in struc tions.
·Do not touch the plug con tacts with sharp, me tal or damp ob jects.
·If the de vi ce is not per ma nent ly moun ted, po si ti on the de vi ce or the ac ces so ry on a non-slip
surface.
·Plea se en su re that you only cle an the sys tem with a slight ly damp cloth.
·Plea se en su re you only use ap pro ved ac ces so ries.
·Only ter mi nals that of fer SELV (sa fe ty ex tra low vol ta ge) and/or meet ETS 300047 may be con -
nec ted to the de vi ce. Cor rect use of the per mit ted ter mi nals meets the se requirements.
Plug power supply unit
·Only use the plug po wer supp ly unit supp lied or avai la ble as an ac ces so ry (DSA-0101F-05 UP or
L15 D52 AB DDLA WO).
·Do not use any plug po wer supp ly units that show signs of da ma ge (bre aks or cracks in the ca -
sing).
Electrostatic charges (ESD protection)
The sys tem te le pho ne is supp lied with ESD pro tec ti on abo ve the per mis si ble va lu es against the ef fects of elec tro sta tic
char ges. In spi te of this, be su re to avoid ex ces si ve sta tic char ges. Va ri ous cau ses can re sult in the elec tro sta tic char ge
achie ving va lu es that far ex ceed the per mis si ble va lu es re qui red and that ex ceed in ter fer en ce im mu ni ty of the sys tem
te le pho ne. The cau ses or cir cums tan ces such as low hu mi di ty or car pets must be eli mi na ted. The ma nu fac tu rer of
the sys tem telephone accepts no liability for damages resulting from these causes.
Sa fe ty no ti ces elmeg IP-S400
4
Un pa cking and po si tio ning
·Sys tem te le pho ne.
·Re cei ver with cord.
·2 de vi ce feet.
·User’s gui de and la bels for functi on keys.
·( elmeg IP-S400)Adap ter ca ble for he ad sets with 4-pin cord, 8-pin / 4-pin.
Setting up the system telephone
Be fo re set ting up the te le pho ne the re ar te le pho ne de vi ce feet must be moun ted 2 in the po si tions mar ked 6 in the
pic tu re.
You can ad just the dis play an gle of the te le pho ne to your an gle of vi si on de pen ding on the height of the se two feet.
Ma ke su re that both of the feet on the de vi ce are the sa me height.
To ad just the height, pull the de vi ce foot away from the ba se of the te le pho ne. Ro ta te it ap prox. 60° along the lon gi tu -
di nal axis and re-in sert the foot in to the hou sing. By ro ta ting the de vi ce foot by ap prox. 60° along the lon gi tu di nal
axis you can adjust it to three different heights.
Plea se re mem ber that the sys tem te le pho ne de vi ce feet may lea ve marks on de li ca te sur fa ces, such as on fit tings for
ex am ples. The sys tem te le pho ne ma nu fac tu rer shall not be li ab le for any such da ma ge. Plea se en su re the re fo re that
you pla ce your sys tem telephone on a non-slip surface.
Cleaning the system telephone
The sys tem te le pho ne has been de sig ned for nor mal usa ge con di tions. On ly cle an the de vi ce when ne ces sa ry with a
slight ly damp cloth or use an an ti-sta tic cloth. Ne ver use sol vents. Ne ver use a dry cloth; the elec tro sta tic char ge could
cau se elec tro nic faults. Ma ke su re that no moi stu re can en ter the sys tem telephone and cause damage.
Connecting the system telephone (connector and receiver cord)
In or der to ope ra te your sys tem te le pho ne, you must in sert the cords for the te le pho ne con nec tor and the receiver.
Connecting the receiver cord
Con nect the re cei ver cord 1 as shown in Fig. 2. Pla ce the re cei ver cord in the ca ble gui de 4 and clamp it se cu re ly un -
der the ca ble clips 5.
Connecting the system telephone (connector and receiver cord) Un pa cking and po si tio ning
5
23
4
5 6
7
4
61
Fig: 2
Connecting the cord
S-con nec tor
Con nect the S-cord 2 as shown in Fig. 2 (so cket S0). Plea se no te that the lon ger ISDN plug must be in ser ted in the
ISDN so cket and the shor ter ISDN plug must be in ser ted in the ISDN so cket on the sys tem te le pho ne. Next pla ce the
S-cord in the ca ble gui de 4 and clamp it se cu re ly un der the ca ble clips 5.
Up0-connectorelmeg CS410-U:
Con nect the S-cord 1 as shown in Fig. 3 (so cket Up0). Plea se no te that the lon ger ISDN plug must be in ser ted in the
ISDN so cket and the shor ter ISDN plug must be in ser ted in the ISDN so cket on the sys tem te le pho ne. Next pla ce the
S-cord ca ble in the ca ble gui de 2 and clamp it se cu re ly un der the ca ble clips 3.
,This elmeg CS410-U may no lon ger be con nec ted to an ISDN con nec tor via an S0 so cket (e.g. in ter nal
S-con nec tor of the elmeg PABX).
,You can con nect a furt her ISDN ter mi nal with S-in ter fa ce (e.g. an ISDN card or anot her sys tem te le -
pho ne) to the S0 so cket on the sys tem te le pho ne. The po wer supp ly at this con nec tor for anot her ISDN
terminal is 1 Watt.
Connecting and setting the headset (not included)
You can con nect a he ad set to the sys tem te le pho ne. Plea se ask your dea ler or con sult the In ter net to find out which
he ad sets are compatible.
elmeg CS410-U elmeg IP-S400.
The he ad set con nec tor on the sys tem te le pho ne is an 8-pin so cket. He ad sets with DSHG in ter fa ce (e.g. cord less DECT
he ad sets) can be con nec ted di rect ly to the sys tem te le pho ne wit hout any ac ces so ries. For stan dard he ad sets (4-pin
cord, e.g. U10PS) use the adapter cable supplied.
Un pa cking and po si tio ning Connecting the system telephone (connector and receiver cord)
6
5
4
3
2
1
Fig: 3
Connecting the headset
The he ad set is con nec ted to the se pa ra te he ad set so cket on the sys tem te le pho ne as shown on pa ge 5 in Fig. 2. Next
pla ce the he ad set ca ble 3 in the ca ble gui de 4 and clamp it se cu re ly un der the ca ble clips 5.
If the he ad set cord do es not fit in the ca ble gui de, stick the ad he si ve ca ble clip supp lied on to the ba se of the sys tem te -
le pho ne 7. Then lay the headset cord under this clip.
Configuring the headset
Headset connectorelmeg CS410 elmeg IP-S400
1Mi cro pho ne +
2Re cei ver (Ground)
3Re cei ver
4Mi cro pho ne (Ground)
Headset connector elmeg CS410-U elmeg CS410,
1DSHG re cei ver
2Earth (Ground)
3Mi cro pho ne +
4Re cei ver (Ground)
5Re cei ver (3.3V swit cha ble over re sis tan ce)
6Mi cro pho ne (Ground)
7V+ (3.3V)
8DSHG trans mit ter
Ot her set tings for the use of the he ad set
You can use eit her the re cei ver or the he ad set to ma ke a call. When using a he ad set, the fol lo wing set tings are re qui red
or available:
·In the con fi gu ra ti on of the sys tem te le pho ne, set up a functi on key for ope ra ting the he ad set (he -
ad set key, see page 36).
·The con nec ted he ad set can be used au to ma ti cal ly for cer tain ope ra tions on the sys tem te le pho ne
(see page ).
·If spe ci al sup port is sa ved in the sys tem te le pho ne for your he ad set, en ter the cor re spon ding type
of he ad set (see page 48).
e.g. the LED in the mi cro pho ne of the »Fi re fly F142 N« from Plan tro nics is swit ched through the
system telephone.
·If you want to use the he ad set to au to ma ti cal ly re cei ve calls, set the time to au to ma tic pi ckup (see
page ). In the con fi gu ra ti on of the sys tem te le pho ne, set up a functi on key for ac ti va ting or de ac ti -
va ting automatic call pickup.
·Using the he ad set the ans we ring ma chi ne can be que ried if au to ma tic he ad set ope ra ti on is set up.
Connecting the system telephone (connector and receiver cord) Un pa cking and po si tio ning
7
43
21
Fig: 4
87
65
43
2
1
Fig: 5
elmeg IP-S400 on the Ethernet connector
PIN configuration PoE
1Trans mit Da ta +
2Trans mit Da ta -
3Re cei ve Da ta +
6Re cei ve Da ta -
4 / 5
7 / 8
Audio in / Audio out
The te le pho ne has an in put 7 and an out put 8 for au dio sig nals. The se con nec tors are in ten ded as a he ad set con -
nec tor. The so ckets are con nec ted to the cor re spon ding so cket con nec tors for the he ad set on the base of the
telephone.
1Plug po wer supp ly unit con nec tor
2Plug po wer supp ly unit
3Ether net PC con nec tor
4PC or ad di tio nal IP te le pho ne
5Ether net / PABX con nec tor
6elmeg PABX
7Au dio-in con nec tor (mi cro pho ne)
8Au dio-out con nec tor (re cei ver)
9He ad set with two 2.5mm ste reo
jack plugs.
Changing the label field
The la bels for the functi on keys can be found on the last pa ge of this user gui de. Re mo ve the se lec ted na me pla te.
To chan ge the pla te, pull the fle xi ble co ver bet ween thumb and fo re fin ger and lift the co ver up wards. The na me pla te
can then be chan ged.
You can la bel the na me pla te via your PC. The elmeg PABX CD-ROM con tains an Ado be Acrobat file with templates.
Pictograms
In or der to be ab le to de mon stra te so me of the pro ces ses in vol ved for set ting up and ope ra ting the te le pho ne in this
user gui de, the fol lo wing pic to grams (sym bols) lis ted below were used.
bLift re cei ver or start pre pa ring to dial.
aRe pla ce re cei ver.
The te le pho ne is idle.
lA call is sig nal led.
The call me lo dy sounds.
Un pa cking and po si tio ning Changing the label field
8
1
2
35
4
7 8
9
6
Fig: 7
87
65
43
2
1
Fig.: 6
gYou are in a call.
dA con fer en ce call is in itia ted.
qYou will hear the po si ti ve or ne ga ti ve ac knowled ge ment tone.
tChoo se call num ber, code, cha rac ter or text.
0 9 ...
* #,
Press a spe ci fic key on the di al ling pad.
You can switch back and forth bet ween the text dis play ed by pres sing the ar row keys
FThe con fi gu ra ti on and set tings are in itia ted by pres sing the functi on key.
SThis key is a soft key; the functi on cor re sponds to the functi on lis ted in the dis play.
OYou can con firm an en try by pres sing the OK key.
ZYou will be promp ted to press one of the functi on or speed dial keys.
zYou will be promp ted to press a spe ci fic functi on or speed dial key.
EThe Es ca pe key ends a cur rent con fi gu ra ti on wit hout sa ving it. Fol lo wing this the te le pho ne is once
again in idle sta te. In en tries for IP functions are com ple ted and then trans fer red byelmeg IP-S400
pressing Escape.
CEn tries such as te le pho ne num bers or na mes can be de le ted by pres sing the Cle ar key. Only one cha -
rac ter is de le ted each time the key is pressed.
RThis key is ne ces sa ry for ma nu al ly hol ding an en qui ry.
WThe re di al ling key starts the re di al ling; pres sing it a num ber of ti mes starts the ad van ced re di al ling or
the au to ma tic redialling.
TAny cur rent con nec tions can be ter mi na ted by pres sing the dis con nect key.
LThe sys tem te le pho ne loud spea ker is swit ched on or off by pres sing the loud spea ker key.
#If you en ter a call num ber to dial via a SIP pro vi der, the num ber di al led is out put ap prox. 5 se conds af -
ter en te ring the last di git. If you end the call num ber with the hash key, the sys tem di als au to ma ti cal ly.
The ter mi nal must be able to dial the hash key in to the PABX.
Pictograms Un pa cking and po si tio ning
9
Sys tem te le pho ne set tings
Connection and operation of the to the elmeg IP-S400 elmeg PABX /elmeg hybird (Basic operation with
DHCP)
Plea se en su re your re ad the elmeg PABX as sem bly in struc tions in or der to see which con nec tors are in ten ded for the
con nec tor to the elmeg IP-S400. Con nect the con nec tor to the Ether net PABX con nec tor on the system telephone.
·Con fi gu re the elmeg PABX for use with IPS sys tem te le pho nes.
·Set the MSN of the IPS sys tem te le pho nes in the elmeg PABX.
·Con nect the po wer supp ly (plug po wer supp ly unit) to the IP sys tem te le pho ne and wait un til the
sys tem te le pho ne has initialised.
If the IP sys tem te le pho ne is in itia li sed, you will be promp ted to choo se a langua ge in the dis play.
Se lect the langua ge for the dis play.Press the ar -
row keys to se lect the langua ges that are avai la ble
and con firm with O.
Welche Sprache? }
deutsch english polski
En ter one of the elmeg MSN en te red in the PABX
(ex am ple 12) .Con firm the en try with .O
Program dial number
MSN-1>12
If no PIN is en te red in the sys tem con fi gu ra ti on,
press O and O again when promp ted.
Please enter login PIN
TNM-1->
SSwitch on »Use DHCP?«.Se lect »on«. Use DHCP?
off on
Sys tem te le pho ne and elmeg PABX are syn chro ni sed.
,If the re is no con nec ti on to the elmeg PABX (no LAN con nec ti on or the sys tem te le pho ne is not re gis -
te red), the time in the dis play is re pla ced by »©---/ /--‰ «.
You can now use the IP sys tem te le pho ne li ke a sys tem te le pho ne on ISDN or UP0.
A com ple te des crip ti on of the con fi gu ra ti on can be found on pa ge .
Pos si ble er ror:
IP ad dress, IP gate way, IP sub net mask, IP SYS ser ver.
MSN is not en te red in the elmeg PABX or is used mul tip le ti mes.
A PIN / lo gin na me is en te red in the elmeg PABX but not in the te le pho ne.
No ex ten si on is set up in the elmeg PABX.
You can now use the IP sys tem te le pho ne li ke a sys tem te le pho ne on S or UP0 con nec tors.
Setting the display language
You can choo se in which langua ge the dis play is to ap pe ar.
Sys tem te le pho ne set tings Setting the display language
10
Start as fol lows:
aFSSS
Re pla ce re cei ver con fig. dis play langua ge
Press the ar row keys to see the langua ges that are avai la ble. Which language? }
deutsch english polski
Ex am ple:
Press the ar row keys to see the langua ges that are avai la ble. Which language? }
deutsch english polski
SPress the soft key un der the cho sen langua ge. The dis play is
im me di ate ly swit ched to the cho sen language.
Entering letters and numbers
If you press a key se ve ral ti mes, you will see cha rac ters (let ters or num bers) dis play ed in se quen ce.
For the en try of let ters and di gits, the keys are as sig ned as follows:
Key First press Se cond
press
Third press Sixth pressFourth press Fifth press Se venth
press
11
2A B C 2 Ä Å Æ
3D E F 3 €
4G H I 4
5J K L 5
6M N O 6 Ö Ø
7P Q R S 7 ß $
8T U V 8 Ü
9W X Y Z 9 ¥
**
##
All of the let ters en te red are dis play ed in up per ca se.
Ex am ple: »bin tec el meg«.
The »0« key has a num ber of spe ci al cha rac ters on it.
E.g.: »!«, » «, » «, » «, » «, » «, » «, » «, » «, » «, … & ? + - = ( ) @ $
When the is first pres sed it in serts a spa ce. If the key is pres sed a se cond time, se ve ral spe ci al cha rac ters are0
shown in the dis play. To se lect a spe ci al cha rac ter, press the al lo ca ted keys ... . If you want to view ot her spe ci al1
cha rac ters, press the 0 key.
Setting the display language Sys tem te le pho ne set tings
11
Display of the performance features set up
When the te le pho ne is at rest, the da te and time are dis -
play ed in the top li ne of the dis play; the pho ne book (tbuch)
and VIP in for ma ti on are dis play ed in the bot tom li ne of the
display.
22.11.09 08:30 }
tbook vip
>
S
In or der to view furt her in for ma ti on about the va ri ous
functions that are set up, press the right ar row key and then
the soft key un der the de si red function.
22.11.05 08:30 i S U {
mail charge info
Additional display information
When the te le pho ne is at rest, ad di tio nal in for ma ti on on the functions that are set up is dis play ed in the top li ne of the
display.
22.11.09 08:30 S U }
tbook vip
Dis play Functi on set up
»S« Di al con trol or call fil ter ac ti vat ed,
Ac cess to sys tem te le pho ne me nus pro tec ted
» «UCall di ver si on (call for war ding) set up.
»i« Sta tus in fo text is avai la ble (e.g. rou ter key).
Displays
Softkey »mail«
Se lect bet ween »uus« und »sms«. Messages
uus sms
UUS
Se lect bet ween »list« und »sms«. Messages / UUS }
list new
<You can choo se bet ween 5 mes sa ges by using the ar row
keys. Se lect the de si red en try to edit by pres sing the O key.
Select text {}
1: HELLO
SIf you wish to send or de le te the mes sa ge, press the cor re -
spon ding »send« or »de le te?« soft key (ex am ple: »send«).
1/HELLO
send delete?
SPress the »UUS Hel lo« soft key. Send mail (Abc)
UUS> HELLO
Sys tem te le pho ne set tings Setting the display language
12
SYou can se lect the de si red call num ber to which the UUS is
due to be sent bet ween »speed di al ling«, »vip«, »re pe at«
and »new«. Press the cor re spon ding softkey.
Send mail / UUS }
direct vip new
Setting the display language Sys tem te le pho ne set tings
13
Te le pho ning
Initiate a call
Dial call number - without option to make a correction
b t g
Lift the re cei ver Di al call num ber Call
Dial call number - with option to make a correction
a t b g
Re pla ce re cei ver Di al call num ber Lift the re cei ver Call
To amend the call num ber or to cor rect an in cor rect en try, se lect the in cor rect di git with the ar row keys and press the
C key to de le te it. Then en ter the cor rect digit.
If you want to car ry out the call using the re cei ver, li fe the re cei ver af ter en te ring the call num ber. At any time du ring a
call, you can switch back and forth bet ween hands free (on ly ), re cei ver and loudspeaker.elmeg IP-S400
Af ter you ha ve en te red a call num ber, you can al so press the loud spea ker key in or der to be ab le to se lect the call num -
ber and use the hands free sys tem (on ly elmeg IP-S400).
Af ter you ha ve en te red a call num ber, you can al so press the loud spea ker key in or der to be ab le to se lect the call
number.
If it is not pos si ble to con nect a call (e.g. call num ber blo cked by di al con trol), a mes sa ge to this ef fect will ap pe ar in the
te le pho ne dis play; e.g.: »Blo cked: Call no.«, if the di al con trol is activated.
If you ha ve lif ted the re cei ver and you are not con nec ted, you can ac cept a call wai ting via the » « soft key wit -ac cept
hout ha ving to re pla ce the re cei ver. You will be no ti fied of the call by a brief mes sa ge. If you set up a con nec ti on key,
you can ac cept the call straight away by pressing the key.
Ot her op tions for di al ling when the re cei ver is re pla ced
It is al so pos si ble to di al a num ber when the re cei ver is re pla ced and to cor rect or supp le ment a call num ber be fo re di -
al ling when calling:
•from the re di al me mo ry (see page 16).
•from the cal ler his to ry(see page 24).
•from the pho ne book on the PABX (see page ).
•from the VIP me mo ry (see page 24).
•using the functi on keys (see page 15).
•via the PABX CTI (TAPI) functi on (elmeg CS410 / elmeg CS410-U).
If you want to use one of the se op tions, you can ma ke furt her en tries be fo re in itia ting the call. You can de ter mi ne, for
ex am ple, whet her or not a call num ber (MSN) is to be trans mit ted to the called party.
Te le pho ning Initiate a call
14
Select from the phone book on the PABX
If you are using the sys tem te le pho ne on a PABX with sys tem te le pho ny, you can di al from the pho ne book on the
PABX.
aStO <> O b g
Re pla ce re cei -
ver
tbuch En ter the in iti al
let ters
En try
se lect
Lift the re cei -
ver
Call
Dialling from the VIP memory
You can pro gram me a VIP en try for each of the 10 di al ling keys con si sting of a na me (max. 20 cha rac ters) and a call
num ber (max. 26 digits).
aS <> or t b g
Re pla ce re cei -
ver
VIP VIP des ti na ti on
se lect
VIP des ti na ti on
se lect
Lift the re cei ver Call
The pro ce du re for pro gram ming VIP en tries is des cri bed on pa ge of this user guide.24
Speed dial with function keys
Speed di al ling is in itia ted using the functi on keys. You can pro gram me two functions or speed di als un der each of the
fi ve keys.
aZb g
Re pla ce re cei ver Pres sing the functi on keys Lift the re cei ver Call
Di al the re qui red call num ber using the functi on keys.
If you want to di al a num ber in the se cond lay er, press the de si red key twi ce. This must be do ne quickly.
,Pro gram ming of the speed dial/functi on keys is done via the PC con fi gu ra ti on or the ad van ced con fi -
gu ra ti on page 47.
Select from the caller history
The te le pho ne has a cal ler his to ry. A ma xi mum of 10 en tries (calls, SMS or UUS1 text mes sa ges) shall be pos si ble in
this list. En tries in the cal ler his to ry are shown on the dis play by pres sing the » « soft key.list
aS <> b g
Re pla ce re cei ver list Se lect en try Lift the re cei ver Call
You will find furt her in for ma ti on on the cal ler his to ry on pa ge 24of this user guide.
Accepting/rejecting a call
With re spect to the telephone’s ba sic set tings, each call shall be sig nal led ir re spec ti ve of the di al led call num ber
(MSN). If two calls are sig nal led si mul ta ne ous ly, the first call is ac cep ted when the re cei ver is lif ted. The se cond call
may con ti nue to be sig nal led by me ans of the call wai ting sig nal.
The num ber of the cal ler and the num ber di al led by the cal ler (MSN-1 … MSN-3, or as sig ned na me) are shown on the
te le pho ne dis play. If on ly MSN-1 is en te red, on ly the entered name is displayed and not the number.
a l b g
Re pla ce re cei ver Lift the re cei ver Call
Accepting/rejecting a call Te le pho ning
15
If you are un ab le to or do not wish to ac cept a call, you can re ject the call. Press the »re ject« soft key and the call will
no lon ger be sig nal led to your te le pho ne. If you are a mem ber of a team, the call is sig nal led to ot her te le pho nes in the
team. If the call was on ly sig nal led to your te le pho ne, Bu sy is sig nal led to the cal ler after it has been rejected.
a l S
Re pla ce re cei ver re ject
Forwarding a call (Call Deflection)
If you are un ab le to or do not wish to ac cept a call, you can for ward the call. Press the »trans fer« soft key in or der to
for ward the call di rect ly to anot her ex ten si on. The call num ber to which the call is due to be for war ded can be pre set
in the te le pho ne con fi gu ra ti on for each call number (MSN).
Af ter pres sing the » « soft key you can eit her for ward the call to the pre set call num ber by pres sing the OKtrans fer
key or en ter a new call number.
a l StO
Re pla ce re cei ver trans fer Di al call num ber (if no call num -
ber has been pre set)
Suppressing the call number (anonymous call)
If you do not want your call num ber to be sent to the cal led par ty, you can sup press the trans mis si on of your call num -
ber. You can set this functi on spe ci fi cal ly for the next call or per ma nent ly (see pa ge 32). The per for man ce fea tu re »ad
hoc sup pres si on of call num ber« must be re ques ted from the network provider.
Sup pres sing trans mis si on of the call num ber for the next call
You can per form in ter nal or ex ter nal di al ling so that the call num ber (MSN) is not trans mit ted from your sys tem te le -
pho ne to the cal led party.
a t OFS b g
Re pla ce re cei -
ver
Di al call num ber se cret Lift the re cei -
ver
Call
If a call is sig nal led, you can de ci de be fo re ac cep ting the call whet her or not your call num ber should be trans mit ted to
the cal ler. If your sys tem te le pho ne is the des ti na ti on of a call di ver si on, you can use this pro ce du re to pre vent the call
see ing the call num ber of the di ver si on destination (your number).
a l > S b g
Re pla ce re cei ver se cret Lift the re cei ver Call
Initiating a call with a fixed call number (MSN)
You can per form in ter nal or ex ter nal di al ling so that a spe ci fic num ber (MSN) is trans mit ted from your sys tem te le -
pho ne to the cal led par ty. This call num ber must first be en te red in your sys tem te le pho ne. Du ring se lec ti on you will
see the call num ber trans mit ted (» «) or the na me you ha ve as sig ned to this call num ber (MSN). MSN-1«...»MSN-3
You can in itia te di al ling with a fi xed num ber as des cri bed be low or use a pro gram med function key (MSN
assignment or user key).
a t OFSS b g
Re pla ce re cei ver Di al call num -
ber
msn msn-
...
1 msn-3
Lift the re cei ver Call
Redialling
The last num ber di al led is sto red in the re di al me mo ry.
Te le pho ning Forwarding a call (Call Deflection)
16
aWg
Re pla ce re cei ver Call
Advanced redialling
The call num bers of the last 10 calls, con nec tions (calls), con nec ti on at tempts or text mes sa ge des ti na tions are sto red
in the ex ten ded re di al ling op ti on. You can view and au to ma ti cal ly di al the se en tries by pres sing the re di al key or the
arrow key.
aW <> O b g
Re pla ce re cei ver Se lect en try Lift the re cei ver Call
The first en try dis play ed is the en try that was ad ded most re cent ly. A let ter is dis play ed at the end of the se cond row to
in di ca te the sta tus of the entry.
» «vCon nec ti on (Call)
»A« Call
»M« Mail (call num bers to which an SMS or UUS1 text mes sa ge has been sent)
» «|Calls for which au to ma tic re di al ling has been set up.
No en try You have cal led an ex ten si on, but not been able to re ach it or the ex ten si on was busy.
Delete call number from the extended redialling option
aW <> F S
Re pla ce re cei ver Se lect en try de le te?
Press the » « soft key to de le te the dis play ed en try straight away. You will now see the next entry.de le te?
Automatic redialling
If you ha ve se lec ted an ex ten si on who is bu sy or who do es not ans wer the call, you can in itia te an au to ma tic di al
functi on in which the de si red ex ten si on is se lec ted again af ter approx. 10 seconds.
b t g Wor S O a
Lift the re cei ver Di al call num -
ber
Ex ten si on bu sy Auto dial Re pla ce re -
cei ver
Af ter ap prox. 10 se conds, the te le pho ne is swit ched on and the call num ber is au to ma ti cal ly di al led. The sys tem at -
tempts to re ach the ex ten si on for approx. 2 minutes.
If the ex ten si on is not rea ched, up to 20 call at tempts are ma de. Af ter 20 un suc cess ful at tempts, au to ma tic re di al ling
is ter mi na ted with a ne ga ti ve acknowledgment tone.
,If au to ma tic di al ling is swit ched on, this is in di ca ted in the dis play by the »au to di al« soft key. Press
the right ar row key to show the nor mal dis play when the te le pho ne is idle.
Interrupt automatic redialling
You can in ter rupt au to ma tic re di al ling at any time by ma king anot her call. Should this be the ca se, press the loud -
spea ker key du ring the au to ma tic re di al ling.
At the end of the call, au to ma tic redial is continued.
Redialling Te le pho ning
17
Deactivate automatic redialling
You can de ac ti va te au to ma tic re di al ling at any time. No ot her call at tempts will then be made.
To de ac ti va te au to ma tic re di al ling du ring an au to ma tic call, press the ESC key.
If you wish to de ac ti va te the au to ma tic re di al ling functi on when the te le pho ne is id le, plea se pro ceed as follows:
aS S
Re pla ce re cei ver Auto dial Yes
Switching the microphone on/off, loudspeaker
Switching the microphone on/off
You can dis ab le the re cei ver mi cro pho ne du ring a call. This pre vents the cal led par ty from hea ring any dis cus sions in
the room. You con ti nue to he ar the cal led party however.
gSRoom que ry Sg
Call mute spe ak Call
,The call du ra ti on or cost me ter will con ti nue to run whilst the mi cro pho ne is swit ched off.
Loudspeaker
If ot her per sons in the room wish to he ar the call, switch on the loud spea ker. You con ti nue to use the re cei ver du ring
the call. You can chan ge the vo lu me du ring the call.
In form the ot her par ty that you are swit ching on the loud spea ker. The ac ti vat ed loud spea ker is shown in the dis play
by »|«.
gL L g
Call Ac ti va te loud spea ker De ac ti va te loud spea ker Call
If you re pla ce the re cei ver whilst the loud spea ker is ac ti vat ed, the re cei ver and loud spea ker are de ac ti vat ed.
Hands free (elmeg IP-S400)
When using hands free, the re cei ver is not used. The built-in mi cro pho ne and the loud spea ker are ac ti vat ed. This can
on ly be ope ra ted by using the loud spea ker / hands free but ton. You can switch to nor mal »re cei ver mo de« whilst in
hands free mo de by lif ting the re cei ver. If you want to switch to hands free mo de when in nor mal »re cei ver mo de«, re -
pla ce the re cei ver whilst pres sing the loud spea ker / hands free but ton. In hands free mo de, acous tic sig nals such as
the call wai ting sig nal are not trans mit ted.
In form the ot her par ty that you are swit ching to hands-free. The ac ti vat ed hands-free functi on is shown in the
display by »|«.
aLt g L
Re cei ver re pla ced In itia te hands free Di al par ti ci pant Call End call
Using the headset
You can con nect a he ad set to the te le pho ne. You can use eit her the re cei ver or the he ad set to ma ke a call.
Te le pho ning Switching the microphone on/off, loudspeaker
18
Switching the headset on/off
In or der to ope ra te the he ad set, a te le pho ne functi on key shall be set up in the form of a he ad set key. The LED a
ned to this but ton in di ca tes whet her the he ad set is swit ched on or off (LED on/off).
azt g z
Re pla ce re cei ver Switch on the he ad set Di al call num ber Call using he ad set Switch off he ad se
Switch volume on or off whilst using the headset
gLgLgz
Call using he ad -
set
Switch on loud -
spea ker
Call using he ad set and
loud spea ker
Switch off loud -
spea ker
Call using he ad -
set
Switch off he ad -
set
Announcement
The an noun ce ment functi on al lows the in ter nal con nec ti on to ot her te le pho nes wit hout them ha ving to ac ti ve ly
cept this con nec ti on (i.e. lift re cei ver, switch vo lu me on). This is a one-si ded con nec ti on in which on ly the ex ten
in itia ting the an noun ce ment is he ard.
The start of the an noun ce ment is signalled by an attention tone.
Initiate announcement
The an noun ce ment is in itia ted by me ans of a code pro ce du re (see el meg PABX user guide).
If your te le pho ne is the des ti na ti on for an an noun ce ment, the call num ber of the an noun cer ap pe ars on the dis p
The an noun ce ment is no ti fied by me ans of an at ten ti on to ne on the loud spea ker. The an noun ce ment can be ter mi
ted with the ESC key.
The an noun ce ment is ac cep ted au to ma ti cal ly by activating the loudspeaker function, if:
·the te le pho ne is idle.
·the an noun ce ment is per mit ted in the PABX (can be con trol led by the »an noun ce ment
on/off« functi on key).
You can in itia te an an noun ce ment via a pro gram med functi on key. An an noun ce ment can al so be in itia ted du ring
exi sting con nec ti on (in hold for en qui ry) using the function keys.
,You can only use this functi on if the an noun ce ment is re lea sed for your in ter nal num ber (MSN) in the
PABX.
Automatic callback
You can re ach an ex ten si on who is cur rent ly bu sy by using the au to ma tic call back functi on. You then re cei ve a
sa ge sta ting that the ex ten si on for which a call back has been set up can now be cal led. This mes sa ge is dis play e
ex ter nal call backs from the ex chan ge and for in ter nal call backs from the PABX.
The te le pho ne dis play then in di ca tes »re call.«. This dis play al ter na tes every 2 se conds bet ween the num ber or
na me of the de si red par ty. As soon as you ac cept this no ti ce (by lif ting the re cei ver, for ex am ple), the sele
subscriber is called automatically.
Automatic callback when busy (CCBS)
When you call the de si red con nec ti on, you he ar the en ga ged to ne. With »Call back on Bu sy« you can re ach the e
ged per son on ce they ha ve re pla ced the re cei ver at the end of the call.
Announcement Te le pho ning
19
Setting up callback
b t g Sa
Lift the re cei ver Di al call num ber Ex ten si on bu sy call back Re pla ce re cei ver
The »call back« soft key is on ly dis play ed if it is pos si ble to set up an au to ma tic call back in the ex chan ge or in the
PABX. For ex ter nal calls the per for man ce fea tu re »Call back on bu sy« must be re ques ted from your network
provider.
You can de fi ne up to 3 call backs. If you use an LCR pro ce du re, an au to ma tic call back is al ways per for med via the stan -
dard net work operator.
,If au to ma tic call back is swit ched on, this is in di ca ted in the dis play by the »Call back« soft key.
Viewing and deleting initiated callbacks
When the te le pho ne is at rest, in itia ted call backs are in di ca ted in the dis play by the » « soft key. To viewcall back
call backs, press this soft key. You can now view the in di vi du al call backs using the ar row keys. If you wish to de le te a
call back, you can se lect this by using the ar row keys, then press the F key and fi nal ly the » « soft key.de le te?
In itia ted call backs are de le ted au to ma ti cal ly af ter a spe ci fied time. This time is de fi ned for ex ter nal call backs by the
net work ope ra tor and for in ter nal call backs by the PABX.
,If the te le pho ne is dis con nec ted from the ISDN net work (e.g. te le pho ne ISDN plugs un plug ged, PABX
swit ched off or re set), then any re ques ted call backs are deleted.
Intercept (MCID)
If you re cei ve a ma li ci ous call, you can sa ve the caller’s num ber in the ex chan ge.
The Tra ce (MCID) per for man ce fea tu re must be re ques ted from the net work pro vi der for your ISDN connection.
,Iden ti fi ca ti on is car ried out in the ex chan ge and is re cor ded un der the caller’s num ber, date and time.
You can use this per for man ce fea tu re in two si tua tions.
During a call
gYou want to iden ti fy the
ex ten si on. >S The call num ber can now be de ter -
min ed in the ex chan ge. a
Call with ex ten si -
on
in ter cept Re pla ce re cei -
ver
After the caller has replaced the receiver
gYou want to iden ti fy the ex -
ten si on, but the cal ler has al -
rea dy re pla ced the re cei ver.
SThe call num ber can now
be de ter min ed in the ex -
chan ge. a
Call with ex ten -
si on
in ter cept Re pla ce re cei ver
Te le pho ning Intercept (MCID)
20
Keypad and tone dialling (MFC dialling)
When con nec ted you can use ot her per for man ce fea tu res by using key pad se quen ces or MFC di al ling. When c
gu ring the te le pho ne you can de ter mi ne in the ba sic set tings whet her key pad se quen ces or MFC di al ling are pos
or not when con nec ted. The dis play shows which functions (keypad or MFC) are available.
Soft key »Key pad« is dis -
play ed.
MFC se quen ces can be en te red im me di ate ly. The key pad is only dis play ed af t
pres sing the softkey.
Soft key »MFC« is dis play ed. Key pad se quen ces can be en te red im me di ate ly. MFC is only dis play ed af ter
sing the softkey.
,Key pad and MFC se quen ces can also be sto red on the functi on keys so that they re main avai la ble
when con nec ted.
Keypad
The key pad functi on al lows you to con trol ser vi ce or per for man ce fea tu res in the PABX or in the operator’s net w
by en te ring cha rac ter and di git strings. Con sult your net work ope ra tor or check out the PABX user gui de to se
»Key pad« is supported or not.
gSt
Call Key pad En ter cha rac ter and di -
git string
Tone dialling (MFC dialling)
By using the MFC di al ling functi on you can send mul ti fre quen cy sig nals (MFC) du ring an exi sting con nec ti on
in or der to re quest an ans werp ho ne for ex am ple. If the re is a call wai ting whilst the re is an exi sting con nec ti on o
te le pho ne, you cannot use the MFC option.
gSt
Call MFC En ter cha rac ter and
di git string
Keypad and tone dialling (MFC dialling) Te le pho ning
21
Te le pho ning with se ve ral peo ple
Call Waiting
If you ha ve en ab led call wai ting for your te le pho ne, you are avai la ble to ot her cal lers du ring an exi sting connection.
gcall wai ting
(Ex ten si on 2) Sg
Call with ex ten si on 1 ac cept Call with ex ten si on 2;
Ex ten si on 1 is on hold
Hold for enquiry
Du ring an exi sting call, you can put up to two furt her con nec tions on hold. To in itia te a hold for en qui ry con nec ti on
you can use the MSN key or a line key.
gRt g
Call with ex ten si on Ex ten si on 1 is on hold Di al call num ber Call with ex ten si on 2
If you want to estab lish ot her con nec tions, pro ceed as des cri bed.
Pres sing the Dis con nect but ton ends the ac ti ve con nec ti on and re turns you to the last held con nec ti on. As soon as
the re is no held con nec ti on, a new con nec ti on is established.
Call transfer in hold for enquiry to an engaged extension
This per for man ce fea tu re is on ly pos si ble with an ex ten si on on hold. You want to for ward a call in hold for en qui ry to
anot her en ga ged extension.
gRt g Sa
Call with ex ten si -
on 1
Ex ten si on 1 is on
hold
Di al call num ber Ex ten si on 2 is bu sy trans fer Re pla ce re cei ver
Ex ten si on1 who is on hold shall he ar mu sic on hold. If Ex ten si on 2 hangs up, the call with Ex ten si on 1 then ta kes
place.
Call forwarding (call transfer)
When trans fer ring a call, the ac ti ve ex ten si on and the ex ten si on of the last held con nec ti on are al ways connected.
You can car ry out a hold for en qui ry (e.g. to an noun ce the call) or trans fer the call di rect ly wit hout an noun ce ment.
gRt g S
Call with ex ten -
si on 1
Ex ten si on 1 is on
hold
Di al call num ber Call with ex ten -
si on 2
trans fer
This performance feature is not currently supported by elmeg hybird!
,Plea se note that when trans fer ring two ex ter nal par ties, this per for man ce fea tu re (ECT - Ex pli cit Call
Trans fer) must be sup por ted by the PABX or, if you use the sys tem te le pho ne di rect ly on the NTBA,
by the network operator.
Brokering
If you ha ve mo re than one ac ti ve con nec ti on on your te le pho ne as a re sult of call wai ting or hol ding (max. 3 con nec -
tions), you can spe ak al ter na ti ve ly with the se ex ten sions (bro ke ring). De pen ding on the num ber of con nec tions on
hold, the re are up to 3 soft keys (»conn1",... «conn3«) avai la ble to you.
Te le pho ning with se ve ral peo ple Call Waiting
22
g> S g> S g
Call with ex ten -
si on
conn1
...
conn3
Call with de si -
red ex ten si on
conn1
...
conn3
Call with de si -
red ex ten si on
If you ha ve set up li ne keys, trans fer ring bet ween the va ri ous ex ten sions is al so pos si ble using the se keys.
To ter mi na te an ac ti ve con nec ti on, press the dis con nect key. You then re turn to the last held connection.
Conference
If you ha ve an ac ti ve con nec ti on and a con nec ti on on hold on your te le pho ne, you can in itia te a con fer en ce cal
both ex ten sions. All three ex ten sions can spe ak to one anot her.
Con fer en ce calls are not pos si ble with mo re than two (2) connections at your phone.
gSgSd
Call with ex ten si on 1 ac cept Call with ex ten si on 2 conf Con fer en ce with ex ten si -
on 1 and ex ten si on 2
In or der to end the con fer en ce, press the » « soft key. You are then re con nec ted to the ex ten si on with the last aback
ti ve con nec ti on. The ot her ex ten si on is now back on hold.
Conference Te le pho ning with se ve ral peo ple
23
Ope ra te sys tem te le pho ne
VIP memory
You can pro gram me a VIP en try for each of the 10 di al ling keys con si sting of a na me (max. 20 cha rac ters) and a call
num ber (max. 26 digits).
This performance feature is not stored in the elmeg hybird.
Programme VIP entry
Start as fol lows:
aF S S S <> O
Re pla ce re cei -
ver
set vip New Se lect VIP des ti na ti on
t
O
En ter the na me for the se lec ted VIP des ti na ti on. Ex am ple:
»bin tec el meg«.
Con firm your in put with O.
Program VIP nam (Abcd)
V0> bintec elmeg
t
O
En ter the call num ber.
Ex am ple: »012345«.
Con firm your in put with O.
Program VIP number.
V0> 012345
Edit VIP entry
Start as fol lows:
aF S S S <> O
Re pla ce re cei -
ver
set vip List Se lect VIP des ti na ti -
on
t
O
Chan ge the na me.
Ex am ple: »bin tec el meg, PE«.
Con firm your in put with O.
Program VIP nam (Abcd)
V0> bintec elmeg,PE
t
O
Chan ge the call num ber.
Ex am ple: »01122334455«.
Con firm your in put with O.
VIP-telefonnr. prog.
V0> 01122334455
Caller history
The te le pho ne has a cal ler his to ry. A ma xi mum of 10 en tries (calls, SMS short mes sa ges or UUS1 text mes sa ges) shall
be pos si ble in this list. En tries in the cal ler his to ry are shown on the dis play by pres sing the » « soft key. The lastlist
10 en tries ma de are al ways in the list. The last en try ad ded is dis play ed first.
When you press this soft key the num ber of new en tries is shown on the dis play (for ex am ple: »New calls: 4!«)
and to get her with the num ber of new SMS or UUS1 mes sa ges (for ex am ple: »Mes sa ges: 2«).
You will al so see the num ber of the en try and the num ber of all en tries in the list be fo re each en try.
E.g.: »3/10: 1122334455...... *«.
If the call num ber of an en try in this list is the sa me as the call num ber of a VIP, the person’s na me who se num ber it is
shall be dis play ed ins te ad of the call num ber. You can view furt her in for ma ti on (pro vi ded it is avai la ble) for each en -
try. If you lift the re cei ver whilst vie wing an en try, the cor re spon ding num ber is di al led au to ma ti cal ly. In di vi du al en -
Ope ra te sys tem te le pho ne VIP memory
24
tries can be de le ted in di vi du al ly from the list. En tries from the PABX pho ne book can al so be dis play ed by na me.
Resetting the telephone will delete the name entry.
Caller history
Calls that you do not ac cept that you in ten tio nal ly re ject are sa ved in the cal ler his to ry.
If a call is com ple ted with a sub scri ber in the cal ler list (you call him or he calls you), the en try is de le ted au to ma ti cal ly
and car ried over to the redial memory.
SMS/UUS1 messages
This performance feature is not currently supported by elmeg hybird!
If you ha ve re cei ved new mes sa ges, the num ber of mes sa ges re cei ved is dis play ed when the te le pho ne is id le. In the
cal ler his to ry you can see the num ber or the na me of the sen der and an in di ca ti on of the mes sa ge ty pe (SMS or UUS1).
Af ter pres sing the F key you can re ad the mes sa ge re cei ved eit her straight away or you can sa ve it in the list of SMS or
UUS1 mes sa ges to re ad la ter.
If you ha ve al rea dy vie wed a new mes sa ge in the list of sa ved UUS1 or SMS mes sa ges, the cor re spon ding en try in the
cal ler list is de le ted. The se en tries shall be deleted following the resetting of the telephone.
UUS1 block
You can ap pro ve and block the re ceipt of in ter nal and ex ter nal UUS1 mes sa ges using the Pro fes sio nal Con fi gu ra tor
or the sys tem telephone.
MWI - Message Waiting Indication (e.g.T-NetBox).
The T-Net Box is an ans we ring ma chi ne that is avai la ble in T-Com, the net work of Deut sche Te le kom AG. The per for -
man ce fea tu re MWI dis plays a no ti ce as soon as a new mes sa ge is re cei ved in your T-Net Box.
The no ti ce is sa ved as an en try in the cal ler list. By se lec ting the en try and lif ting the re cei ver, you can con nect to your
T-Net Box, for ex am ple, in or der to lis ten to new mes sa ges. The en try in the cal ler list is au to ma ti cal ly de le ted, if no
new mes sa ges ap pe ar, e.g. on the T-Net Box. You can al so de le te the en try ma nu al ly.
You can on ly use this functi on if the MWI per for man ce feature is supported by your ISDN connection and the PBX.
Viewing the caller history
a
s
The te le pho ne is id le. The »list« soft key in the bot tom li -
ne of the dis play in di ca tes if an en try exists in the cal ler his -
to ry.
Press this softkey.
New call!
Messages: 1
UUS today 14:33 {}
1/4: 05171717171
FYou can re ad and sa ve this mes sa ge. 1/20 * }
read save
In the first li ne of the dis play you will see the se lec ted en try ty pe (»Call«, » «, »UUS SMS« ), the da te (for the first two
days »To day« or »Yes ter day«), the time and the se lec ted call num ber (MSN).
Caller history Ope ra te sys tem te le pho ne
25
»*«
»a«
»I«
new call, UUS1 or SMS text mes sa ge
Call
In for ma ti on about mes sa ges e.g. on your T-Net box (MWI)
,When you view the cal ler his to ry again, call en tries that you have al rea dy seen but not de le ted will be
mar ked with »a« ins te ad of with »*«.
You can view ot her en tries by using the ar row keys. Call today 08:50 {}
1/02:12 a
FIf you wish to view in for ma ti on about an en try or de le te the
en try, press .F
»de le te?« The en try is de le ted im me di ate ly.
» Vie wing ot her in for ma ti on on the re cei ved call. Info«
E.g.: The num ber for which the mes sa ge was sent and the num ber of the sender.
C
For furt her in for ma ti on press the »in fo« soft key . You
will now see in for ma ti on on the call. If not all in for ma ti on
can be dis play ed, press the ar row keys to dis play furt her in -
for ma ti on.
Press the to exit the menu.C
1/121 a
delete info
Deleting the caller history
De le ting an en try
aS <> F> S
Re pla ce re cei ver list Se lect en try de le te?
SMS and UUS1 text messages
You can use the te le pho ne to send or re cei ve SMS or UUS1 text mes sa ges (SMS - Short Mes sa ge Ser vi ce, UUS1 - User
to User Sig nal ling). A text mes sa ge is en te red using the te le pho ne key pad. For the text en try of let ters, di gits or spe ci al
cha rac ters, the keys are as sig ned as des cri bed on pa ge 11.
You can on ly send and re cei ve text mes sa ges if the sen der trans mits his num ber and if this is dis play ed to the re ci -
pient. Text mes sa ges wit hout a trans mit ted call num ber are not transmitted.
The re ceipt of a text mes sa ge is sig nal led with two short at ten ti on to nes on the te le pho ne. When the te le pho ne is id le,
the num ber of mes sa ges re cei ved is dis play ed and a re fer en ce to the se is dis play ed in the caller history.
Any SMS/UUS1 mes sa ges that are re cei ved and sent are sa ved in a list in the te le pho ne. 10 re cei ved SMS/UUS1 mes -
sa ges and 2 sent SMS/UUS1 mes sa ges can be sa ved. Plea se no te that the re must be free me mo ry avai la ble in or der to
be ab le to sa ve SMS/UUS1 mes sa ges. If you p30-ha ve al rea dy sa ved 5 re cei ved SMS/UUS mes sa ges then you can not re cei -
ve any mo re SMS/UUS1 messages (information on display).
An SMS mes sa ge shall be tem po ra ri ly sa ved af ter it is sent. You shall be ab le to ac cess the se sa ved SMS/UUS mes sa ges
un til they are over writ ten by a newly sent SMS/UUS1 message.
The se en tries shall be de le ted fol lo wing the re set ting of the te le pho ne.
The sen ding of SMS/UUS1 text mes sa ges shall be pos si ble to both in ter nal and ex ter nal te le pho nes. You can on ly ma -
ke use of this per for man ce fea tu re to ex ter nal te le pho nes if »SMS/UUS1 (User to User Sig nal ling)« is ac ti vat ed for
your ISDN connection.
Ope ra te sys tem te le pho ne SMS and UUS1 text messages
26
Important notes on entering the call number for sending SMS messages
If the per for man ce fea tu re »Au to ma tic Out si de Li ne« for your te le pho ne is swit ched off in the PABX, you will not be
ab le to en ter the di al ling code be fo re en te ring the des ti na ti on num ber. In ad di ti on the di al ling code must be sa ved in
the te le pho ne.
When the te le pho ne is con nec ted to a PABX with au to ma tic out si de li ne, you can enter the destination number
directly.
View new text messages received
You can view a new mes sa ge from the cal ler his to ry (see pa ge ) or from the list of re cei ved text mes sa ges. If you p32-ha ve 24
al rea dy vie wed a new mes sa ge in the list of re cei ved text mes sa ges, the cor re spon ding en try in the cal ler history is
deleted.
Viewing received or sent text messages
When vie wing re cei ved or sent text mes sa ges, you can ac cess the fol lo wing functions:
•Re send a text mes sa ge.
Be fo re sen ding, the text mes sa ge can be mo di fied.
•De le te a text mes sa ge.
•Trans fer text mes sa ge to the list of sa ved text mes sa ges (only UUS1).
Start as fol lows:
a>SSS
Re pla ce re cei ver mail uus or sms read
Example: Read received UUS1 text message
The text mes sa ge ad ded last is dis play ed first. A new text mes sa ge that has not been re ad is mar ked with »*«. The fol -
lo wing in for ma ti on can be dis play ed for a text message:
•Num ber of the text mes sa ge in the list (Ex am ple: »1/3«).
•Call num ber to which the text mes sa ge was trans mit ted (Ex am ple: »MSN-1«).
•Call num ber of the sen der / Re ci pient of the text mes sa ge (Ex am ple: »2200«).
O
Press the ar row keys to see the full text mes sa ge.
Press to ac cess a me nu with furt her op tions.O
UUS 1/2 { 2200
TxT
In the top li ne of the dis play you will see the da te and time
at which you re cei ved the mes sa ge. To se lect an ac ti on,
con firm with the cor re spon ding softkey.
UUS 1 today 14:21 }
send delete? more
»send« Mo di fy and then send text mes sa ge.
To send the text mes sa ge, pro ceed as des cri bed un der »Crea ting and sen ding text mes sa ges« (see page
27).
»del?« De le te the text mes sa ge.
» View next tem po ra ry sa ved text mes sa ge.con ti nue «
>
S
Press the ar row key and se lect »list.UUS 1 today 14:21 {
list
Ope ra te sys tem te le pho ne SMS and UUS1 text messages
28
O
Use the ar row keys and se lect the de si red mes sa ge and con -
firm your se lec ti on with .O
Save text {}
1: TxT
Permanently saved text messages (only UUS1)
Up to fi ve UUS1 text mes sa ges can al rea dy be sa ved in the te le pho ne. You can edit, de le te or send the se text mes sa ges.
Text mes sa ges that are al rea dy sa ved can on ly be en te red di rect ly on the telephone.
Start as fol lows:
a> S S S
Re pla ce re cei ver mail uus list
Press the ar row keys to se lect a text mes sa ge. Select text {}
1: TxT
OPress O in or der to en ter or amend the se lec ted text mes -
sa ge. Press O to con firm your fi nal en tries.
FPress in or der to send or de le te a mes sa ge.F1/ TXT
send delete?
»send« Mo di fy and then send text mes sa ge.
To send the text mes sa ge, pro ceed as des cri bed un der »Crea ting and sen ding text mes sa ges« (see page
27).
»del?« De le te the text mes sa ge.
Send text messages automatically (only UUS1)
When on a call, you can au to ma ti cal ly send a UUS1 text mes sa ge to the cal ler. To do this, the text 1 from the list of per -
ma nent ly sa ved text mes sa ges is always used.
Start as fol lows:
a> S S > S
Re pla ce re cei ver mail uus in co ming
SPress the » « soft key to switch au to ma tic sen -in co ming
ding on or off.
Send Text 1 with call?
no ok
Set receipt for text messages (only UUS1)
You can con fi gu re whet her ex ter nal or in ter nal UUS1 text mes sa ges are re cei ved by the te le pho ne or not. Re ceipt can
be blo cked se pa ra te ly for ex ter nal and in ter nal text messages.
Start as fol lows:
a> S S > S
Re pla ce re cei ver mail uus uus_re ceipt
SMS and UUS1 text messages Ope ra te sys tem te le pho ne
29
SPress the »ex ter nal« or »in ter nal« soft key to switch
the re ceipt of UUS1 text mes sa ges on or off. E.g.:
»ex ter nal«: Re ceipt of ex ter nal mes sa ges in hi bi ted.
»in ter nal«: Re ceipt of in ter nal messages is possible.
Inhibit reception
internal external
Error receiving an SMS message
If you are un ab le to re cei ve an SMS mes sa ge or on ly as voi ce out put, the re may be se ve ral reasons:
•If you are un ab le to trans mit an SMS mes sa ge, a cor re spon ding er ror code is dis play ed. Con sult the SMS ser vi ce
of your net work ope ra tor / pro vi der to find out which er ror codes are displayed.
•The SMS per for man ce fea tu re has not been re gis te red with the net work ope ra tor and/or the pro vi der of the
SMS cen tre for your ISDN connection.
•The SMS mes sa ge was trans mit ted by a third-par ty ser vi ce pro vi der, which fai led to trans mit this mes sa ge as
an SMS message.
•Per ma nent num ber sup pres si on is ac ti vat ed for your ISDN con nec ti on.
•5 SMS mes sa ges are al rea dy sa ved in the te le pho ne, mea ning the re fo re that no more SMS mes sa ges can be
received.
•Check the sys tem te le pho ne and PABX sett tings
Ope ra te sys tem te le pho ne SMS and UUS1 text messages
30
Che cking costs
You can ob tain de tails on ac cu mu la ted call costs on your te le pho ne. You can on ly use this functi on if the AOCD / AO -
CE per for man ce fea tu re is ac ti vat ed for your ISDN con nec ti on by the network operator.
Con sult your net work ope ra tor to find out what op tions are avai la ble for trans mit ting cost in for ma ti on. Plea se no te
that the trans fer of all cost in for ma ti on from the ex chan ge to your te le pho ne is no lon ger pos si ble for tech ni cal rea -
sons. Any pri ce re duc tions re cei ved, spe ci al ta riffs used and spe ci al fea tu res may le ad to de via tions bet ween the da ta
sa ved in the te le pho ne and the data stated on the telephone bill.
Procedure for transmitting cost information
The re are va ri ous pro ce du res for trans mit ting cost in for ma ti on. The sa me pro ce du re is nor mal ly al ways ap plied to a
con nec tor. This pro ce du re is au to ma ti cal ly re cog ni sed by the te le pho ne and is saved for future use.
If the trans mis si on of cost in for ma ti on du ring a pro ce du re oc curs that is not sa ved in the te le pho ne, then »In cor -
rect cost ty pe« is shown in the dis play.
In this ca se de le te all of the cost in for ma ti on sto red in the te le pho ne (see al so: Vie wing/de le ting to tal costs). Re co gni -
ti on and sa ving of the pro ce du re used to trans mit cost information is then re-activated.
,You can set up the ta riff fac tor and de no mi na ti on via the PC or Ad van ced con fi gu ra ti on page 47.
Viewing and deleting costs
Cannot be configured using the system telephone on the elmeg hybird!
You can view the costs for in di vi du al calls as well as for all ac cu mu la ted calls and de le te the en tries. You can al so view
and de le te the call costs via the Pro fes sio nal Configurator.
View/delete costs of last call
Start as fol lows:
a> S
Re pla ce re cei ver char ge
SThe cost of the last call is dis play ed. If you want to de le te
the se costs, press the » « soft key.de le te?
Last conn.: 0,18EUR }
single delete? sum
View/delete total costs
Start as fol lows:
a>SS
Re pla ce re cei ver char ge sum
You can view the to tal cost for all call num bers (MSN). If
you want to de le te the se costs, press the »de le te?« soft -
key.
Total: 0,31 EUR }
single delete? sum
,If the to tal cost is de le ted, all MSN cost ac counts are de le ted at the same time. The re co gni ti on and sa -
ving of the pro ce du re for trans mit ting cost in for ma ti on is re-activated.
Viewing and deleting costs Che cking costs
31
View/delete costs of individual call numbers (MSN)
Start as fol lows:
a>S>S
Re pla ce re cei ver char ge MSN-1
You can view the to tal cost for a sing le call num ber. Ex am -
ple for »MSN-2«.
MSN-2: 0,06 EUR {
msn-1 msn-2 msn-3
<
S
If you wish to de le te the to tal costs for the se lec ted num ber
(ex am ple MSN-2), press the left ar row key and then the
»de le te?« soft key.
MSN-2: 0,18 EUR }
single delete? sum
Set up tariff factor and denomination
Start as fol lows:
aF S S
Re pla ce re cei ver con fig. char ge
»ta riff«En ter the ta riff fac tor and con firm your en try with . The length of the ta riff fac tor is li mit ed to 4O
cha rac ters. Press the as te risk key to en ter a comma.
»cur ren cy«En ter the de no mi na ti on and con firm your en try with O. The length of the name is li mit ed to 6 cha -
rac ters. For the text en try of let ters, di gits or spe ci al cha rac ters, the keys are as sig ned as des cri bed on
page 11.
»del?« All cost in for ma ti on sa ved in the te le pho ne will be de le ted. Re co gni ti on and sa ving of the pro ce du re
used to trans mit cost in for ma ti on (see page ) is re-activated.31
Transmission of the call number correctly set up (CLIP/CLIR/COLP/COLR)
Start as fol lows:
aF S S S
Re pla ce re cei ver con fig. dis play call no.
SBy pres sing the »in co ming« , »yes - no« soft key, the dis play of the caller’s num ber is swit ched on
or off.
SBy pres sing the » « soft key, the dis play of the cal led party’s num ber is swit -out going« , »yes - no
ched on or off.
Che cking costs Set up tariff factor and denomination
32

Produkt Specifikationer

Mærke: Bintec-elmeg
Kategori: Telefon
Model: CS410-U

Har du brug for hjælp?

Hvis du har brug for hjælp til Bintec-elmeg CS410-U stil et spørgsmål nedenfor, og andre brugere vil svare dig


Telefon Bintec-elmeg Manualer

Bintec-elmeg

Bintec-elmeg IP-S400 Manual

28 August 2024
Bintec-elmeg

Bintec-elmeg S560 Manual

28 August 2024
Bintec-elmeg

Bintec-elmeg elmeg DECT80 Manual

28 August 2024
Bintec-elmeg

Bintec-elmeg Elmeg CS410 Manual

28 August 2024
Bintec-elmeg

Bintec-elmeg S530 Manual

28 August 2024
Bintec-elmeg

Bintec-elmeg CS410-U Manual

28 August 2024

Telefon Manualer

Nyeste Telefon Manualer

Gigaset

Gigaset E290M Manual

9 April 2025
Bogen

Bogen MCDS4 Manual

1 Marts 2025
Bogen

Bogen CA15C Manual

1 Marts 2025
Ubiquiti Networks

Ubiquiti Networks G3 Touch Enterprise Manual

25 Februar 2025
POCO

POCO X3 GT Manual

22 Februar 2025
POCO

POCO M4 Pro 5G Manual

22 Februar 2025
Doro

Doro Leva X10 Manual

11 Februar 2025
Cyber Acoustics

Cyber Acoustics SP-2000 Manual

7 Februar 2025
HMD

HMD 110 4G Manual

30 Januar 2025
Yealink

Yealink AX83H Manual

24 Januar 2025