Blebox parkingsensor Manual

Blebox Ikke kategoriseret parkingsensor

Læs nedenfor 📖 manual på dansk for Blebox parkingsensor (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 61 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
SAFETY RULES
Connect only in accordance with the diagram presented in the
manual. Improper connections may be dangerous, it can damage
the controller, and loss of the warranty.
Do not connect the device to loads exceeding the permitted
values.
DANGER! Risk of electric shock! Even with the device turned o,
the outputs may be live. All assembly work should be ALWAYS
performed with the disconnected power circuit.
The installation of the device to a power mains that does not
meet the quality requirements dened by EN 50081-1, EN
50082-1, UL508, EN 60950, will result in the loss of the warranty.
PARKING SENSOR LED / LED RGB LIGHTING CONTROLLER
Before installing the sensor, disconnect the voltage in the supplied circuit.
Remember that all assembly work should be carried out with the power
supply disconnected.
The sensor should be mounted in a place protected from adverse environ-
mental conditions. It is advisable that the device is mounted in a stable and
stationary position.
Connect the LED strips and power supply to the device according to the
diagram.
Optionally, connect the LED lamp indicating the occupancy of the parking
space. When the vehicle is within range of the sensor, the lamp will remain on
continuously.
1INSTALLATION
sensor
bumper/number plate
frame/light
source
Mount the device vertically at the height of the farthest part of the car
(usually a bumper or license plate) as in the drawing below, so that the
connector is at the bottom.
Connect the power supply. Bring your hand or paper closer to the ParkingSen-
sor sensor, the color of the light should change with the detector:
2FIRST START-UP
3MOVEMENT OF THE VIRTUAL WALL
the time of the color illumination (red / blue / green) is 10 seconds, while the
optional LED lighting shines during the entire period of occupancy of the
parking space.
the range of the color changes are established in relation to the virtual wall. By
default, the virtual wall is at a physical distance of 2 cm from the sensor. It can
be adjusted in the physical range 2 cm..250 cm of the sensor by performing
the following steps:
1.
2.
3.
4.
5.
place a at object (for example, a piece of cardboard) in front of the
sensor at the desired distance, such as a virtual wall;
connect the power supply; wait 5 seconds; disconnect the power supply;
connect the power supply; wait 10 seconds; disconnect the power
supply;
connect the power supply; wait 15 seconds; disconnect the power
supply;
connect the power supply; wait until the LED strip turn on white and
then turn o, which means that the conguration has been saved; check
if the virtual wall works as expected.
CONNECTION DIAGRAM
green color
blue color
red colour
pulsing red color
you can move forward safely
you are close to the obstacle
stop the vehicle
stop the vehicle immediately!
option of signaling the occupied
space
LED STRIP
110 / 230V
12 - 24 V
+
power
supply
G
R
B
B R G - 0 +
LED STRIP*
*
-


Produkt Specifikationer

Mærke: Blebox
Kategori: Ikke kategoriseret
Model: parkingsensor

Har du brug for hjælp?

Hvis du har brug for hjælp til Blebox parkingsensor stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Blebox Manualer

Blebox

Blebox gateBox Manual

29 August 2024
Blebox

Blebox shutterBox Manual

29 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg

Smeg KIT6PX Manual

23 December 2024
Smeg

Smeg KIT6CX Manual

23 December 2024
Smeg

Smeg GTA-6 Manual

23 December 2024