Britax-Römer Trifix 2 I-Size Manual

Britax-Römer Bilsæde Trifix 2 I-Size

Læs nedenfor 📖 manual på dansk for Britax-Römer Trifix 2 I-Size (2 sider) i kategorien Bilsæde. Denne guide var nyttig for 32 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

Seat shell

ISOFIX locking arms

Fabric loop

Operating instructions compartment

Adjusting ring of the headrest

Tilt adjustment lever

Adjustment belt

Adjustment button

Shoulder straps

Shoulder pads

Release button

Harness buckle

Headrest

ISOFIX insertion aids

ISOFIX fastening points (car) Top tether

1. PRODUCT OVERVIEW

2. APPROVAL

These instructions use the following symbols stated below:

Symbol Keyword Explanation

DANGER! Risk of severe personal injury

WARNUNG! Risk of minor personal injury

CAUTION! Risk of material damage

TIP: Useful notes

3. USE IN THE VEHICLE

Please observe the instructions for using children's restraining systems in the

operating instructions of your vehicle. During use, be sure to observe any restric-

tions relating to airbags.

Please refer to the operating instructions for your vehicle for information about

vehicle seats which are certiﬁed for the use of children's restraining systems according

to ECE R16.

TRIFIX² i-SIZE usage options:

BRITAX RÖMER

child safety seat

Vehicle seat position with ISOFIX and

top tether

i-Size Not i-Size

TRIFIX² i-SIZE

You can use your child safety seat as follows:

In the direction of travel Yes 1)

Against the direction of

travel

On seats featuring:

ISOFIX fastenings (be-

tween the seat surface

and backrest) and top

tether anchoring points

(e.g. on the loading area,

on the ﬂoor or behind the

backrest)

Yes 2)

(Please observe the applicable regulations in force in your country)

1) Using the seat in a backwards-facing car seat (e.g. in a van or minibus) is only permitted if

the car seat is also approved for transporting adults. The seat may not be in the area of eect

of an airbag.

2) If there is a passenger airbag: Slide the passenger seat well backwards and follow any

relevant directions in your vehicle's operating instructions.

76–105cm

≤ 22kg

Safety button

01 02

We are pleased that you have chosen our

TRIFIX² i-SIZE

to accompany your child safely through a new stage of his or her life.

In order to protect your child correctly, the

TRIFIX² i-SIZE

must always be used and installed as described in these instructions.

The

TRIFIX² i-SIZE

is exclusively intended to secure your baby

in your vehicle.

BRITAX RÖMER

child safety seat

Tested and approved according to

ECE* R 129/02

Body size Body weight

TRIFIX² i-SIZE

76–105 cm NJ

*ECE = European Standard for Child Safety Equipment

The child safety seat has been designed, tested and approved according to

the requirements of the European Standard for Child Safety Equipment (ECE

R 129/02). The seal of approval "E" (in a circle) and the approval number are

located on the orange approval label (sticker on the child safety seat).

DANGER! This certiﬁcation will be invalidated if you make any modiﬁca-

tions to the child safety seat. Only the manufacturer is permitted

to make modiﬁcations to the child safety seat. Unauthorised

technical changes can cause the protective function of the

seat to be reduced or completely eliminated. Do not make any

technical changes to the child safety seat.

Use the DANGER!

TRIFIX² i-SIZE

exclusively for securing your child in your

vehicle. It is in no way suitable for use as a seat or toy in the

home.

PAGE I

4. CARE AND MAINTENANCE

Cleaning

Please only use authentic BRITAX RÖMER replacement seat covers. The

seat cover is an integral part of the child safety seat and is key to ensuring the

trouble-free functionality of the system. Replacement seat covers are available

from your dealer.

• The cover can be removed and washed with a mild detergent in the

delicates programme of the washing machine (30°C). Please observe the

instructions on the washing label of the cover.

• The shoulder pads can be removed and washed in luke-warm soapy

water.

• The plastic parts and the harness can be cleaned with soapy water. Do not

use any caustic cleaning agents (such as solvents).

Care for the harness buckle

To ensure the safety of your child, it is absolutely essential that the harness

buckle continues to function correctly. Harness buckle malfunctions are usu-

ally caused by a build-up of soiling or by external objects:

• When you press the red release button, it takes a long time for the buckle

tongues to be ejected.

• The buckle tongues no longer engage (i.e. when you try to push them in,

they pop out again).

• The buckle tongues engage without an audible "click".

• The buckle tongues are dicult to push in (you feel a certain amount of

resistance).

• The buckle can only be opened by applying extreme force.

Remedy: Clean the harness buckle so that it functions properly again with no

trouble:

Cleaning the harness buckle

1. Open the harness buckle 04 (press the red release button).

2. Unhook the elastic seam of the cover from the bottom edge of the seat

shell 17.

3. Open the Velcro fastener on the crotch pad 18 and pull it over the harness

buckle 04 along with the cover.

4. Rotate the crotch harness with the metal plate 19 which holds the har-

ness buckle 04 in the seat shell 17 by 90° in the longitudinal slot.

5. Slide the metal plate 19 through the harness slot 20 with the narrow edge

facing forwards.

6. Soak the buckle 04 in warm water containing washing-up liquid for at least

an hour. Rinse the buckle thoroughly and dry it.

7. Slide the metal plate 19 fully into the longitudinal slot from the front.

8. Rotate the crotch harness with the metal plate 19 by 90° until it is hooked

into the harness slot 20 on the seat shell 17 perpendicular to the direction

of motion.

DANGER! Tug hard on the harness buckle 04 to make sure that it is

secure in the seat shell 17.

9. Thread the harness buckle 04 through the crotch pad 18 on the cover

and then re-fasten the Velcro fastener and the cover.

Removing the cover

1. Push the tilt adjustment lever 11 upwards and slide back the seat shell 17

to upright position.

2. Loosen the shoulder straps 08 as far as possible.

3. Open the harness buckle 04 (press the red release button).

4. Open the Velcro fastener on the crotch pad 18.

5. Slide the headrest 03 into the lowest position.

6. Pull o the cover of the headrest 03.

7. Open the snap fasteners on the left and right of the rear part of the cover.

8. Turn over the rear part of the cover onto the seat surface.

9. Thread the shoulder straps 08 through the recesses in the cover. Unhook

the elastic seam of the cover from the bottom edge of the seat shell.

TIP: Start with the handles on the side and top of the seat shell.

10. Pull the cover up and over the border of the strap adjuster.

11. Unthread the harness buckle 04 and the strap end 09 from the cover.

12. Pull the cover upwards a little and then put it with the recess over the

headrest 03 .

DANGER! The child seat must not be used without the seat cover.

Reattaching the cover:

Proceed in reverse order to put on the cover.

The harnesses must not be twisted and must be correctly posi-Caution:

tioned in the harness slots.

Removing the shoulder pads

1. Loosen the shoulder straps 08 as far as possible.

2. Slide the headrest 03 into the second position from the top.

3. Fold up the bottom part of the headrest 03 upwards.

4. Open the shoulder pads 07 at the Velcro fasteners at the side.

Rear of the child safety seat

5. Open the operating instructions compartment 14 .

6. Pull out the shoulder straps 08 a little so that you can see the strap loops

of the shoulder pads 07 underneath.

7. Unhook the strap loops from the plastic fasteners 25 of the height ad-

juster.

8. Pull the shoulder pads 07 forwards out of the harness slots.

Re-attaching the shoulder pads:

Simply follow the steps above in reverse order.

The shoulder pads Caution: 07 or harnesses must not be twisted or

changed places. The shoulder straps 08 must be located under the black

cover band 21 in the shoulder pads 07 .

04 18 19 20

07 07

76–105cm

≤ 22kg

TRIFIX² i-SIZE

User instructions

2000029654 20/05

www.britax-roemer.com

Produkt Specifikationer

Mærke:	Britax-Römer
Kategori:	Bilsæde
Model:	Trifix 2 I-Size

Har du brug for hjælp?

Hvis du har brug for hjælp til Britax-Römer Trifix 2 I-Size stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Bilsæde Britax-Römer Manualer

Britax-Römer Kidfix M I-size Manual

13 Maj 2024

Britax-Römer Baby-Safe Isofix Base Manual

24 December 2023

Britax-Römer Swingfix M i-Size Manual

12 December 2023

Britax-Römer Kidfix XP Manual

19 September 2023

Britax-Römer KIDFIX III M Manual

21 August 2023

Britax-Römer Baby-Safe iSense Manual

21 April 2023

Britax-Römer Dualfix Manual

2 April 2023

Britax-Römer Baby-Safe Manual

2 Marts 2023

Britax-Römer KIDFIX 2 S Manual

28 December 2022

Britax-Römer Trifix 2 I-Size Manual

21 December 2022

Bilsæde Manualer

Nyeste Bilsæde Manualer

Avionaut Pixel Pro 2.0 C Manual

22 December 2024

Avionaut AeroFIX RWF 2.0 C Manual

22 December 2024

Venicci Tiago Manual

20 December 2024

Inglesina Base Darwin belted Manual

20 December 2024

Inglesina Copernico Manual

20 December 2024

Inglesina Ally Pad Manual

20 December 2024

Inglesina Cartesio i-Size Manual

20 December 2024

Inglesina Prima Miglia Manual

20 December 2024

Inglesina Galileo I-Fix Manual

20 December 2024

Inglesina Magellano Manual

20 December 2024