Chief SLB175 Manual

Chief Vægophæng SLB175

Læs nedenfor 📖 manual på dansk for Chief SLB175 (1 sider) i kategorien Vægophæng. Denne guide var nyttig for 41 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/1

I N S T A L L A T I O N I N S T R U C T I O N S

CSAV, Inc., and its affiliated corporations and subsidiaries (collectively, "CSAV"), intend to make this manual accurate and complete. However, CSAV makes no claim that the infor-

mation contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The

information contained in this document is subject to change without notice or obligation of any kind. CSAV makes no representation of warranty, expressed or implied, regarding the

information contained herein. CSAV assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918

8802-000243

11/2/06

SLB-175 and SLM-175 Interface Brackets

SLB and SLM series Interface brackets are designed for use with Chief RPA, RPM, and Smart-Lift series projector mounts. See the specific

installation instructions provided with the mount for additional installation information.

Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative by calling

1-800-582-6480.

WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND

DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!

Installation:

WARNING: OVERTIGHTENING OF SCREWS CAN DAMAGE PARTS AND LEAD TO SERIOUS PERSONAL INJURY AND DAMAGE

TO EQUPIMENT! DO NOT over tighten screws when installing interface brackets.

NOTE: Step 1 is only required when installing an SLB Interface bracket. If an SLM bracket is being installed proceed to step 2.

1. Screw six thumb screws onto six 10-24 x 5/8" Philips pan head screws. DO NOT fully tighten thumb screws at this time.

2. Turn projector upside down on a flat surface.

3. Place Interface bracket onto bottom of projector and align bracket with three threaded inserts in bottom of projector.

4. Secure Interface bracket to projector, using three M6 x 16mm Philips pan head screws and flat washers.

NOTE: Security screws can be substituted when mounting Interface bracket to projector by using the parts and installation instructions in the

All-Points Security Kit.

(1) Interface Bracket (3) Washers, Flat, M6

(6) 10-24 Thumb Nuts ** (3) Screw, Philips Pan Head, Machine, M6 x 20mm

(1) All-Points Security Kit

**Only used when installing SLB Interface brackets.

SLB-175

SLM-175

Produkt Specifikationer

Mærke:	Chief
Kategori:	Vægophæng
Model:	SLB175
Produktfarve:	Sort
Kompatible produkter:	Infocus Screenplay 777
Maksimal vægtkapacitet:	- kg

Har du brug for hjælp?

Hvis du har brug for hjælp til Chief SLB175 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Vægophæng Chief Manualer

27 Juni 2024

15 Maj 2024

14 Maj 2024

14 Maj 2024

14 Maj 2024

11 Maj 2024

10 Maj 2024

7 Maj 2024

Vægophæng Manualer

Nyeste Vægophæng Manualer

12 Oktober 2024

12 Oktober 2024

12 Oktober 2024

12 Oktober 2024

12 Oktober 2024

12 Oktober 2024

One For All DM 2110 Manual

10 Oktober 2024

One For All DM 4220 Manual

10 Oktober 2024

One For All DM 2120 Manual

10 Oktober 2024

One For All DM 4210 Manual

7 Oktober 2024