Chief SLM208 Manual

Chief Projektor tilbehør SLM208

Læs nedenfor 📖 manual på dansk for Chief SLM208 (1 sider) i kategorien Projektor tilbehør. Denne guide var nyttig for 11 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/1

I N S T A L L A T I O N I N S T R U C T I O N S

CSAV, Inc., and its affiliated corporations and subsidiaries (collectively, "CSAV"), intend to make this manual accurate and complete. However, CSAV makes no claim that the infor-

mation contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The

information contained in this document is subject to change without notice or obligation of any kind. CSAV makes no representation of warranty, expressed or implied, regarding the

information contained herein. CSAV assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918

8802-000274

10/18/07

SLB-208 and SLM-208 Interface Brackets

for BENQ SP830, SP831

SLB and SLM series Interface brackets are designed for use with Chief RPA, RPM, and Smart-Lift series projector mounts. See the specific

installation instructions provided with the mount for additional installation information.

Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative by calling

1-800-582-6480.

WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND

DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!

Installation:

WARNING: OVERTIGHTENING OF SCREWS CAN DAMAGE PARTS AND LEAD TO SERIOUS PERSONAL INJURY AND DAMAGE

TO EQUIPMENT! DO NOT over tighten screws when installing interface brackets.

NOTE: Step 1 is only required when installing an SLB Interface bracket. If an SLM bracket is being installed proceed to step 2.

1. Screw four thumb screws onto four 10-24 x 5/8" Philips pan head screws. DO NOT fully tighten thumb screws at this time.

2. Turn projector upside down on a flat surface.

3. Place the interface bracket onto the bottom of the projector lining up the four holes in the bracket with the four threaded inserts in the bottom

of the projector.

4. Using the four M4 X 10mm mounting screws and washers, start them into the mounting holes by hand and secure all four fasteners at this

time.

NOTE: Security screws can be substituted when mounting Interface bracket to projector by using the parts and installation instructions in the

All-Points Security Kit.

(1) Interface Bracket (4) WASHER, Flat, M4

(4) 10-24 Thumb Nuts ** (4) SCREW, Pan Head, M4 x 10mm

(1) All-Points Security Kit

**Only used when installing SLB Interface brackets.

SLB-208

SLM-208

Towards front of Towards front of

Projector

Produkt Specifikationer

Mærke:	Chief
Kategori:	Projektor tilbehør
Model:	SLM208

Har du brug for hjælp?

Hvis du har brug for hjælp til Chief SLM208 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Projektor tilbehør Chief Manualer

Chief CHCMS115 Manual

30 August 2024

Chief CMS036 Manual

21 August 2024

Chief SSB176 Manual

21 August 2024

Chief SSM116 Manual

21 August 2024

Chief CMS006009W Manual

21 August 2024

21 August 2024

21 August 2024

21 August 2024

21 August 2024

21 August 2024

Projektor tilbehør Manualer

Nyeste Projektor tilbehør Manualer

Barco R9861400 Manual

27 September 2024

Barco R9832766 Manual

15 September 2024

Barco R9842370 Manual

12 September 2024

Barco R9855978 Manual

6 September 2024

My Wall HL 41 ML Manual

5 September 2024

Speaka SP-PWM-200 Manual

5 September 2024

Speaka SP-PWM-100 Manual

5 September 2024

Speaka PRB-1 Manual

5 September 2024

Roadinger UP-4 QCL Manual

5 September 2024

Panasonic ET-D3LEW300 Manual

5 September 2024