Chief SLM215 Manual

Chief Projektor tilbehør SLM215

Læs nedenfor 📖 manual på dansk for Chief SLM215 (1 sider) i kategorien Projektor tilbehør. Denne guide var nyttig for 10 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/1

I N S T A L L A T I O N I N S T R U C T I O N S

Milestone AV Technologies, Inc., and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone

makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation

or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, ex-

pressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this

document.

• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918

8850-000145 Rev.A

3/17/08

SLB-215 and SLM-215 Interface Brackets

for Sharp XV-Z90U, Sharp Vision Theago DT-200

SLB and SLM series Interface brackets are designed for use with Chief RPA, RPM, and Smart-Lift series projector mounts. See the specific

installation instructions provided with the mount for additional installation information.

Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative by calling

1-800-582-6480.

WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND

DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!

Installation:

WARNING: OVERTIGHTENING OF SCREWS CAN DAMAGE PARTS AND LEAD TO SERIOUS PERSONAL INJURY AND DAMAGE

TO EQUIPMENT! DO NOT over tighten screws when installing interface brackets.

NOTE: Step 1 is only required when installing an SLB Interface bracket. If an SLM bracket is being installed proceed to step 2.

1. Screw four thumb screws onto four 10-24 x 5/8" Philips pan head screws. DO NOT fully tighten thumb screws at this time.

2. Turn projector upside down on a flat surface.

3. Place the interface bracket onto the bottom of the projector lining up the four mounting holes in the bracket with the four threaded inserts

in the bottom of the projector.

4. Using the four M4 X 10mm mounting screws, start them into the mounting holes by hand and secure all four fasteners at this time.

NOTE: Security screws can be substituted when mounting Interface bracket to projector by using the parts and installation instructions in the

All-Points Security Kit.

(1) Interface Bracket (4) Washer, Flat, M4

(4) 10-24 Thumb Nuts ** (4) Screw, Pan head, M4 x 10mm

(1) All-Points Security Kit

**Only used when installing SLB Interface brackets.

SLB-215

SLM-215

Towards front of

Projector

Produkt Specifikationer

Mærke:	Chief
Kategori:	Projektor tilbehør
Model:	SLM215

Har du brug for hjælp?

Hvis du har brug for hjælp til Chief SLM215 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Projektor tilbehør Chief Manualer

Chief CHCMS115 Manual

30 August 2024

Chief CMS036 Manual

21 August 2024

Chief SSB176 Manual

21 August 2024

Chief SSM116 Manual

21 August 2024

Chief CMS006009W Manual

21 August 2024

21 August 2024

21 August 2024

21 August 2024

21 August 2024

21 August 2024

Projektor tilbehør Manualer

Nyeste Projektor tilbehør Manualer

Barco R9861400 Manual

27 September 2024

Barco R9832766 Manual

15 September 2024

Barco R9842370 Manual

12 September 2024

Barco R9855978 Manual

6 September 2024

My Wall HL 41 ML Manual

5 September 2024

Speaka SP-PWM-200 Manual

5 September 2024

Speaka SP-PWM-100 Manual

5 September 2024

Speaka PRB-1 Manual

5 September 2024

Roadinger UP-4 QCL Manual

5 September 2024

Panasonic ET-D3LEW300 Manual

5 September 2024