Conair DPC3300R Manual

Conair Brusehoved DPC3300R

Læs nedenfor 📖 manual på dansk for Conair DPC3300R (3 sider) i kategorien Brusehoved. Denne guide var nyttig for 15 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/3
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE INSTALLING AND
USING THIS PRODUCT.
OPERATION INSTRUCTIONS
Congratulations on your purchase of the Pollenex Showerhead Set.
Your showerheads are manufactured from quality materials and will
give you years of convenient use in your bathroom.
CAUTION! SILICONE GLUE MAY CAUSE EYE IRRITATION.
MAY CAUSE SKIN IRRITATION.
MAY CAUSE RESPIRATORY TRACT IRRITATION.
Avoid contact with eyes. Do not handle contact lenses with product
on hands. Avoid contact with skin and clothing. Wash thoroughly after
handling. Avoid breathing vapor. Use with adequate ventilation.
FIRST AID
IN CASE OF EYE CONTACT, immediately flush eyes with plenty of
water for 15 minutes. Get medical attention. IN CASE OF SKIN
CONTACT, immediately flush/wash skin with soap and plenty of water.
Get medical attention. IN CASE OF INHALATION DISCOMFORT,
move to fresh air. Dispose ofKEEP OUT OF REACH OF CHILDREN.
unused portion immediately.
INSTALLING THE SHOWERHEAD SET
Step 1: Remove the old showerhead by turning it counterclockwise
(Fig. 1). Wipe off any debris from the threaded pipe. Wrap the
teflon tape clockwise around the threaded pipe (Fig. 2).
Step 2: Install the diverter valve on the pipe. Turn clockwise with your
hand to tighten. . (Fig. 3). Then, install Note: Do not over-tighten
the new wall-mount showerhead to the forward-facing diverter
opening by turning it clockwise and tightening by hand. If
additional tightening is required, place protective cloth on the
swivel nut and tighten with a wrench (Fig. 4).
Step 3: Attach the ridged nut end of the hose to the downward-facing
diverter valve opening (Fig. 5). Attach the other end of the hose
to the hand-held showerhead (Fig. 6) and turn clockwise to
tighten by hand.
Note: The ridged nut end of the shower hose contains a permanently
installed device to protect from the backflow of water which is
standard for all showerheads. To function properly the ridged nut
end of the hose must be connected to the diverter.
Step 4: You can affix the holder to the surface of tiles, marble, fiberglass,
plastic, glass or acrylic with the enclosed silicone glue (keep out
of reach of children). Before fastening the holder, clean off any
debris from the wall using alcohol and make sure surface is
clean and dry. Apply the silicone glue to the back of the holder.
If desired, use screw holes provided in holder for added
support. (Screws are not included).
Step 5: Press the holder firmly against the wall for at least 2 minutes
(Fig. 7). Allow the glue to dry for 24 hours before resting the
hand-held showerhead in the holder.
EASY TO OPERATE
Turn the diverter control valve to adjust the spray from the wall-mount
only to hand-held only or a combination of both showerheads. (Fig 8).
CLEANING AND MAINTENANCE
Clean with gentle non-abrasive cleanser and soft cloth.
Fig. 1 Fig. 2
Fig. 3 Fig. 7
Fig. 8
Fig. 4
Fig. 5 Fig. 6


Produkt Specifikationer

Mærke: Conair
Kategori: Brusehoved
Model: DPC3300R

Har du brug for hjælp?

Hvis du har brug for hjælp til Conair DPC3300R stil et spørgsmål nedenfor, og andre brugere vil svare dig