Conair DPP143 Manual
Læs nedenfor 📖 manual på dansk for Conair DPP143 (2 sider) i kategorien Jern. Denne guide var nyttig for 12 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/2
IMPORTANT
SAFEGUARDS
When using your iron, basic precautions should
always be followed, including the following:
READ ALL INSTRUCTIONS
BEFORE USING.
1. Use iron only for its intended use.
2. To protect against a risk of electric shock, do not
immerse the iron in water or other liquid.
3. The iron should always be turned off before
unplugging from an outlet. Never yank cord to
disconnect from outlet; instead, grasp plug and
pull to disconnect.
4. Do not allow cord to touch hot surfaces.
5. Let iron cool completely before putting away.
6. Loop cord loosely around cord wrap when
storing.
7. Always disconnect iron from electrical outlet
when filling with or emptying water and when not
in use.
8. Be careful to avoid spilling water over iron when
filling.
9. Do not operate any appliance with a damaged
cord or plug or after the appliance malfunctions
or is dropped or damaged in any manner.
10. If the product requires attention within
the warranty period, call the toll-free number
listed in the warranty section of this manual for
information on examination, repair, or electrical
or mechanical adjustment.
11. To avoid the risk of electric shock, do not
disassemble the iron; instead, take it to an
authorized service center for examination and
repair. Incorrect reassembly can cause risk of
electric shock when the iron is used.
12. This appliance should not be used by or near
children or persons with disabilities.
13. Do not leave iron unattended while connected
or on an ironing board.
14. Always position iron carefully to prevent it
from falling if ironing board is accidentally moved
or cord is pulled. Always use heel rest.
15. Burns can occur from touching hot metal
parts, hot water or steam.
16. Use caution when you turn a steam iron upside
down. There may be hot water in reservoir.
17. If you need to clean the iron, unplug and allow
to cool. Use a slightly damp cloth and wipe down
the outside of the iron. Do not use cleaning agents
or place the iron in water or cleaning fluids.
18. Burns can occur from touching hot metal
parts, hot water, or steam. Use caution when you
turn a steam iron upside down or use vertical
burst of steam — there may be hot water in
the water tank. Avoid rapid movement of iron to
minimize water spillage.
19. When using burst of steam, always direct the
steam vents away from your body and others.
20. Do not operate in the presence of explosive
and/or flammable fumes.
21. Do not use iron outdoors.
22. This product is for household use only, not for
commercial or industrial use.
23. Be sure dual voltage selector is in correct
voltage position before plugging iron into wall
outlet. This appliance was set at the factory
to operate at 120 volts. Refer to Operating
Instructions section of this manual for conversion
to 240 volt operation.
SPECIAL
INSTRUCTIONS
To avoid circuit overload, do not operate another
high wattage appliance on the same circuit. If
an extension cord is absolutely necessary, a 15-
ampere rated cord with a polarized plug and UL,
CSA or NOM approval should be used. Cords rated
for less amperage may overheat. Care should be
taken to arrange the cord so that it cannot be
pulled on or tripped over.
SAVE THESE
INSTRUCTIONS
POLARIZED PLUG
This appliance has a polarized plug (one blade is
wider than the other). As a safety feature, this plug
will fit into a polarized outlet only one way. If the plug
does not fit fully into the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician. Do
not attempt to defeat this safety feature.
Thanks for your purchase of the Conair™ EZ Press.
We have used the highest quality materials in the
production of this clothing iron to ensure long-
lasting performance.
Please be sure to read the following instructions
carefully before you use your Conair™ EZ Press for
the first time. Once you have familiarized yourself
with this appliance, please save this instruction
manual for future reference.
OPERATING
INSTRUCTIONS
PREPARING FOR FIRST USE
Before first use, remove all labels from the
soleplate and housing. Before you use the iron
to press fabrics for the first time, heat it to the
highest temperature setting without adding any
water, then turn the iron off, allow to cool, and
unplug iron.
1. The tank can be filled with
ordinary tap water. However, for
optimal performance, distilled
water is suggested.
a. Using a clean measuring
cup, slowly fill the tank until
the water reaches the Max indicator.
DO NOT OVERFILL.
b. Wipe off any water that may have spilled on
the outside of the iron with a soft clean cloth.
2. Set the iron on a stable, flat surface when
selecting the settings. We recommend using a
quality ironing board as the pressing surface. Be
sure to give yourself enough room to maneuver
the iron when pressing.
3. Plug the iron into a 120V electrical receptacle.
Make sure that no other high wattage appliances
are plugged into the same circuit.
4. Align fabric setting “dot” with setting indicator
located on tank under handle.
5. The iron will heat up to the setting on the
dial. Once the temperature is reached, the ready
indicator will go off and the iron is ready to use.
6. For steam use, please ensure that the dial
is set to the 3-dot setting to prevent water
from dripping.
FABRIC CARE TIP Start with delicate, low-temp
fabrics first and move up to high-temp fabrics
like linen. You can choose from minimum one
dot (•), to two dots (••) or three dots (•••).
See the accompanying chart to match the dots
to your fabric.
TEMPERATURE CONTROL DIAL
• •• •• •
(one dot) (two dots) (three dots)
Low Medium High
Acrylic Silk Wool
Nylon Rayon Cotton
P Linenolyester
ADJUSTING STEAM ON/OFF
This iron is capable of both dry pressing and steam
pressing. Dry pressing is best for delicate fabrics,
like silk, that may be damaged by steam.
1. To dry press, choose a fabric setting between
Min and Medium (•• two dots).
Be sure the variable steam control is in the off
position; otherwise water may drip from soleplate.
2. To press with steam, set the temperature
control dial to the steam icon or higher (Max
setting). Be sure the variable steam control is in
the steam position.
3. The burst of steam is used to eliminate tough
wrinkles. While pressing, push the burst of
steam button to get a maximum steam through
the fabric. Too many bursts in a row will cool the
soleplate and take the iron out of the appropriate
temperature setting. If temperature is below the
steam setting, water may drip from soleplate.
FABRIC CARE TIP Dry pressing is also a good
second step after steam pressing cotton pants,
to achieve a crisp crease.
VERTICAL STEAMING
This iron will help remove wrinkles and freshen
garments on hangers, or draperies, with bursts
of steam.
1. Hang the item that you want to treat, such as
a suit jacket.
2. Set the iron to the highest setting: 3 dots.
3. Hold the iron with the soleplate facing the
fabric, but not touching it.
4. Turn the vertical steam control from 0 to
(steam icon) to activate steam burst.
5. Press the burst of steam button. Make sure
the burst of steam is penetrating the fabric.
Repeat until the wrinkles have been removed or
the fabric has been freshened to your liking.
When you have finished pressing or vertical
steaming, unplug the iron. Be sure to allow the
iron to cool completely before storing.
CONVERTING VOLTAGE
Iron is factory set to operate at 120 volts. To
convert iron to operate at 240V, make sure iron
is unplugged. Move dual voltage switch from
120V position to 240V position. If necessary,
use a small screwdriver to help move the switch.
Follow Operating Instructions.
GET TO KNOW YOUR
EZ PRESS™
Antislip
rubber heels
Temperature
control dial
8’ cord length
Variable
steam
control
Burst of
steam
button
Temperature
ready light
800 watts
Stainless steel
soleplate
Setting
indicator
Dual Voltage
Switch
(on bottom
plate)
WARNING
If the iron has been dropped, unplug the iron
and inspect it for damage. If there is obvious
damage or if you hear any loose parts or
suspect the iron has been damaged, contact
Conair Customer Service at 1-800-3-CONAIR to
arrange for service. Be extremely cautious if you
have dropped the iron. Until unplugged exposed
electrical components could cause an electric
shock, serious injury or death.
TROUBLESHOOTING
Iron does not heat
• Make sure that the iron is plugged in and turned
on. Make sure to select a fabric.
Iron does not steam
• The iron will produce steam only at the highest
setting (three dots). Make sure the iron is set to
that setting.
• The steam control must not be set to the “no
steam” setting.
• Make sure the water tank is full.
Water leaks from the soleplate
• Make sure that you are using the burst of steam
in the highest setting, If not, the iron will not be hot
enough to produce steam.
• When storing the iron turn the steam control to
“no steam” setting. Try to store the iron sitting on
the heel rest.
LIMITED ONE YEAR WARRANTY
Conair will repair or replace (at our option) your
unit free of charge for 12 months from the date
of purchase if the appliance is defective in
workmanship or materials.
To obtain service under this warranty, return
the defective product to the service center
listed below together with your purchase receipt
and $3.00 for postage and handling. California
residents need only provide proof of purchase
and should call 1-800-3-CONAIR for shipping
instructions. In the absence of a purchase
receipt, the warranty period shall be 12 months
from the date of manufacture.
ANY IMPLIED WARRANTIES, OBLIGATIONS,
OR LIABILITIES, INCLUDING BUT NOT
LIMITED TO THE IMPLIED WARRANTY OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, SHALL BE LIMITED
IN DURATION TO THE 12 MONTH DURATION
OF THIS WRITTEN, LIMITED WARRANTY.
Some states do not allow limitations on how
long an implied warranty lasts, so the above
limitations may not apply to you.
IN NO EVENT SHALL CONAIR BE LIABLE
FOR ANY SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL
DAMAGES FOR BREACH OF THIS OR ANY
OTHER WARRANTY, EXPRESS OR IMPLIED,
WHATSOEVER.
Some states do not allow the exclusion or
limitation of special, incidental, or consequential
damages, so the above limitation may not apply
to you. This warranty gives you specific legal
rights, and you may also have other rights,
which vary from state to state.
©2007 CONAIR CORPORATION
Service Center:
Conair Corporation
Service Department
7475 N. Glen Harbor Blvd.
Glendale, AZ 85307
07NP256 IB-8026
ez press™
steam
iron
User Guide
For your safety and continued enjoyment of this product,
always read the instruction book carefully before using.
DPP143 Series
Produkt Specifikationer
Mærke: | Conair |
Kategori: | Jern |
Model: | DPP143 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Conair DPP143 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Jern Conair Manualer
1 Oktober 2024
6 September 2024
21 August 2024
21 August 2024
21 August 2024
20 August 2024
20 August 2024
Jern Manualer
- Jern DeLonghi
- Jern Sinbo
- Jern Bosch
- Jern SilverCrest
- Jern OBH Nordica
- Jern Sencor
- Jern Singer
- Jern Siemens
- Jern Breville
- Jern Panasonic
- Jern Gorenje
- Jern VOX
- Jern Miele
- Jern Philips
- Jern Concept
- Jern Vitek
- Jern LG
- Jern AEG
- Jern Electrolux
- Jern Shark
- Jern Elica
- Jern Braun
- Jern Hotpoint
- Jern Melissa
- Jern Hoover
- Jern Korona
- Jern Arçelik
- Jern ProfiCare
- Jern Grundig
- Jern Livoo
- Jern Klarstein
- Jern Tefal
- Jern Trisa
- Jern Princess
- Jern Emerio
- Jern Moulinex
- Jern Sunbeam
- Jern Westinghouse
- Jern Hyundai
- Jern Proctor Silex
- Jern Jura
- Jern Imetec
- Jern TriStar
- Jern Clas Ohlson
- Jern Adler
- Jern Black And Decker
- Jern Camry
- Jern Blaupunkt
- Jern Tomado
- Jern AEG-Electrolux
- Jern Becken
- Jern BEKO
- Jern Privileg
- Jern Alpina
- Jern Clatronic
- Jern Quigg
- Jern Hitachi
- Jern Rowenta
- Jern Fagor
- Jern Haier
- Jern AFK
- Jern Bomann
- Jern Morphy Richards
- Jern Russell Hobbs
- Jern Ariete
- Jern Innoliving
- Jern Maxim
- Jern Zelmer
- Jern Leifheit
- Jern Vivax
- Jern JML
- Jern Calor
- Jern Sunny
- Jern Telefunken
- Jern Primo
- Jern Orbegozo
- Jern Optimum
- Jern Taurus
- Jern Exquisit
- Jern Elba
- Jern MPM
- Jern Profilo
- Jern Tesla
- Jern G3 Ferrari
- Jern Domo
- Jern BEEM
- Jern GlobalTronics
- Jern Swann
- Jern Thomas
- Jern Hamilton Beach
- Jern Ambiano
- Jern Unold
- Jern Nevir
- Jern Ursus Trotter
- Jern Inventum
- Jern Cleanmaxx
- Jern Swan
- Jern Khind
- Jern Frigidaire
- Jern SVAN
- Jern Scarlett
- Jern Izzy
- Jern ECG
- Jern Nova
- Jern Saturn
- Jern Eldom
- Jern Maxwell
- Jern H.Koenig
- Jern Proline
- Jern Waves
- Jern Termozeta
- Jern Laurastar
- Jern Easy Home
- Jern Polti
- Jern Eta
- Jern Turmix
- Jern Orion
- Jern Rotel
- Jern Kalorik
- Jern Cecotec
- Jern Solac
- Jern CHI
- Jern Beper
- Jern Tower
- Jern Team
- Jern Jocca
- Jern Brentwood
- Jern Duronic
- Jern Bestron
- Jern Philco
- Jern Kunft
- Jern Arzum
- Jern LERAN
- Jern Hacienda
- Jern Andis
- Jern Oster
- Jern Jocel
- Jern Ufesa
- Jern DPM
- Jern Create
- Jern Flama
- Jern Kambrook
- Jern Jata
- Jern Aigostar
- Jern Heinner
- Jern Defy
- Jern First Austria
- Jern Drew & Cole
- Jern Qilive
- Jern Lümme
- Jern Johnson
- Jern Koblenz
- Jern Essentiel B
- Jern Gallet
- Jern Zephir
- Jern Superior
- Jern Grunkel
- Jern Coline
- Jern Elta
- Jern Imarflex
- Jern Lelit
- Jern Girmi
- Jern Zomix
- Jern Vanguard
- Jern Domena
- Jern Eudora
- Jern Elgento
- Jern High One
- Jern Lagrange
- Jern Robinhood
- Jern LAFE
- Jern Inno-Hit
- Jern Britania
- Jern Vaporella
- Jern Kleva
- Jern Steamfast
- Jern Michelini
Nyeste Jern Manualer
21 December 2024
21 December 2024
21 December 2024
21 December 2024
21 December 2024
21 December 2024
21 December 2024
21 December 2024
21 December 2024
21 December 2024